Click here to download

FT-1500M Manual

FT-1500M Operating Manual
Front Panel Controls & Switches

VOL Knob
This control adjusts the volume level of the receiver’s audio.
Clockwise rotation increases the volume level.

DIAL
This 20-position detented rotary switch is used for tuning, memory
selection and most function settings. Note that the microphone’s UP/DOWN
buttons duplicate the tuning functions of the Main Dial.

Display
The display consists of segmented digits which indicate operating
frequency, status of functions, alpha/numeric memory labels, and MENU
functions.

MHz
This button allows tuning in 1-MHz steps (the MHz digits will blink
on the display). If receiving on a memory, pressing this button the
first time activates the Memory Tune (MT) mode, and pressing it
again enables 1-MHz steps.
Press and hold this key for one second to activate the Set Mode.

REV
During split-frequency operation, such as through a repeater, this
button reverses the transmit and receive frequencies.
Press and hold this key for one second to activate the Dual Watch
feature, described in the Operation chapter (“PRI” will be displayed
on the LED, indicating “Priority Channel” monitoring).

LOW
Toggle this button while receiving to select high/low transmitter
power (?/? watts).
Press and hold this key for one second to while receiving on a
memory, pressing this button toggles the
display between indication of the frequency and the channel’s
Alpha/Numeric label.

D/MR
This button selects the operation modes: VFO mode, Memory mode, and
HOME channel.
Press and hold this key for one second to activate the Memory Storage mode.

PWR Switch
This is the main “ON/OFF” switch for the transceiver.

LCD
Memory Skip
DTMF Memory Mode
BELL
Frequency
Auto Power OFF Active
LOCK Feature Active
S- and TX Power Meter
LOW Power
Memory Mode
Repeater Shift
Priority Channel Scanning
Tone Encoder/Squelch Enabled
Smart Search
Programmable Memory Scan
Home Channel
VFO
Side Panel Connector
Microphone Jack
This 6-contact modular jack accepts transmit audio, tone call
(burst) or Dial / Memory selection, and
Scanning control from the microphone.
Pin 1: Sw 2 (Multi-function switching)
Pin 2: Cloning
Pin 3: +9V
Pin 4: GND
Pin 5: Microphone Input
Pin 6: Sw 1 (Multi-function switching)
Rear Panel Connector
ANT Coaxial Socket
Connect a resonant 144-MHz antenna to this type-M (SO-239) socket
using 50-W coaxial cable and a
type-M (PL-259) plug.
13.8V DC Cable Pigtail w/Fuse
This is the power supply connection for the transceiver. Use the
supplied DC cable to connect this
pigtail to the car battery or other DC power supply capable of at
least 10 Amperes (continuous duty).
Make certain that the red lead connects to the positive side of the
supply. The fuse in the DC Cable is
rated at 15-A, fast-blow.
EXP SP Jack
This 2-contact 3.5-mm phone jack provides receiver audio output for
an optional external speaker. The
audio impedance is 4 Ohms, and the level varies according to the
setting of the front panel’s VOL
control. Inserting a plug into this jack disables audio from the
transceiver’s internal speaker.
DATA Jack
This six-pin mini-DIN jack accepts AFSK or FSK input from a
Terminal Node Controller (TNC) ; it
also provides fixed-level Receiver Audio Output, Push-To-Talk
(PTT), and Ground lines.
Accessories & Options
Accessories Supplied with the FT-1500M
Operating Manual
Warranty Card
Available Options for your FT-1500M
???????????
Availability of accessories may vary: some accessories are supplied
as standard per local regulations
and requirements, others may be unavailable in some regions. Check
with your Yaesu dealer for
additions to the above list.
Installation
This chapter describes the installation procedure for integrating
the FT-1500M into a typical amateur
radio station. It is presumed that you possess technical knowledge
and conceptual understanding
consistent with your status as a licensed radio amateur. Please
take some extra time to make certain
that the important safety and technical requirements detailed in
this chapter are followed closely.
Preliminary Inspection
Inspect the transceiver visually immediately upon opening the
packing carton. Confirm that all
controls and switches work freely, and inspect the cabinet for any
damage. Gently shake the
transceiver to verify that no internal components have been shaken
loose due to rough handling during
shipping.
If any evidence of damage is discovered, document it thoroughly and
contact the shipping company (or
your local dealer, if the unit was purchased over-the-counter) so
as to get instructions regarding the
prompt resolution of the damage situation. Be certain to save the
shipping carton, especially if there
are any punctures or other evidence of damage incurred during
shipping; if it is necessary to return the
unit for service or replacement, use the original packing materials
but put the entire package inside
another packing carton, so as to preserve the evidence of shipping
damage for insurance purposes.
Installation Tips
To ensure long life of the components, be certain to provide
adequate ventilation around the cabinet of
the FT-1500M.
Do not install the transceiver on top of another heat-generating
device (such as a power supply or
amplifier), and do not place equipment, books, or papers on top of
the FT-1500M. Avoid heating vents
and window locations that could expose the transceiver to excessive
direct sunlight, especially in hot
climates. The FT-1500M should not be used in an environment where
the ambient temperature exceeds
+60° C (140° F).
Safety Information
The FT-1500M is an electrical apparatus, as well as a generator of
RF (Radio Frequency) energy, and
you should exercise all safety precautions as are appropriate for
this type of device. These safety tips
apply to any device installed in a well-designed amateur radio
station.
r Do not allow unsupervised children to play in the vicinity of
your transceiver or antenna installation.
r Be certain to wrap any wire or cable splices thoroughly with
insulating electrical tape, to prevent
short circuits.
r Do not route cables or wires through door jambs or other
locations where, through wear and tear,
they may become frayed and shorted to ground or to each other.
r Do not stand in front of a directional antenna while you are
transmitting into that antenna. Do not
install a directional antenna in any location where humans or pets
may be walking in the main
directional lobe of the antenna's radiation pattern.
r In mobile installations, it is preferable to mount your antenna
on top of the roof of the vehicle, if
feasible, so as to utilize the car body as a counterpoise for the
antenna and raise the radiation pattern
as far away from passengers as possible.
r During vehicular operation when stopped (in a parking lot, for
example), make it a practice to switch
to Low power if there are people walking nearby.
r Never wear dual-earmuff headphones while driving a vehicle.
Antenna Considerations
The FT-1500M is designed for use with antennas presenting an
impedance of near 50 W at all
operating frequencies. The antenna (or a 50 W dummy load) should be
connected whenever the
transceiver is turned on, to avoid damage that could otherwise
result if transmission occurs
accidentally without an antenna.
Ensure that your antenna is designed to handle 50 Watts of
transmitter power. Some magnetic-mount
mobile antennas, designed for use with hand-held transceivers, may
not be capable of this power level.
Consult the antenna manufacturer's specification sheet for details.
Most all FM work is performed using vertical polarization. When
installing a directional antenna such
as a Yagi or Quad, be certain to orient it so as to produce
vertical polarization, unless you are engaged
in a special operating situation where horizontal polarization is
used.
Note that this transceiver is designed with wide frequency coverage
in the VHF spectrum. For general
listening, you may wish to have a broadband antenna such as a
discone available, as a directional
antenna such as a Yagi will have degraded performance outside the
2-meter Amateur band.
Excellent reference texts and computer software are available for
the design and optimization of VHF
antennas. Your dealer should be able to assist you with all aspects
of your antenna installation
requirements.
Use high-quality 50 ohm coaxial cable for the lead-in to your
FT-1500M transceiver. All efforts at
providing an efficient antenna system will be wasted if poor
quality, lossy coaxial cable is used.
Losses in coaxial lines increase as the frequency increases, so an
8-meter-long (25’) coaxial line with
0.75 dB of loss at 28 MHz may have a loss of 1.8 dB or more at 146
MHz; choose your coaxial cable
carefully based on the installation location (mobile vs. base) and
the overall length of the cable
required (for very short runs of cable in a mobile installation,
the smaller, more flexible cable types
may be acceptable).
For reference, the chart below shows approximate loss figures for
typically-available coaxial cables
frequently used in VHF installations.
Loss in dB per 30 m (100 feet) for Selected 50-ohm Coaxial Cables
(Assumes 50-ohm Input/Output Terminations)
Loss: 144 MHz
6.5
4.7
3.0
2.0
1.5
1.0
0.7
Cable Type
RG-58A
RG-58 Form
RG-8A, RG-213
RG-8 Form
Belden 9913
1/2” “Hardline”
7/8” “Hardline”
Loss figures are approximate; consult cable manufacturers’ catalogs
for complete specifications.
In outdoor installations, be certain to weatherproof all connectors
thoroughly, as water entering a
coaxial cable will cause losses to escalate rapidly, thus
diminishing your communications
effectiveness. The use of the shortest possible length of the
highest quality coaxial cable that fits
within your budget will ensure the best performance from your
FT-1500M.
Mobile Installation
The FT-1500M must only be installed in vehicles having a negative
ground electrical system. Mount
the transceiver where the display, controls, and microphone are
easily accessible, using the supplied
MMB-?? mounting bracket. The transceiver may be installed in any
position, but should not be
positioned near a heating vent nor anywhere where it might
interfere with driving (either visually or
mechanically). Make sure to provide plenty of space at the rear of
the transceiver so that air can flow
freely through the heatsink. Refer to the diagrams showing proper
installation procedures.
Transceiver Installation
r Choose a mounting location with sufficient clearance for the
transceiver. Using the mounting
bracket as a template for the mounting holes, use a 4.8 mm (3/16”)
bit to drill the mounting holes, and
secure the mounting bracket with the supplied screws, washers, and
nuts (see diagram).
r Position the transceiver in the bracket so that the holes in the
side are aligned with those in the
bracket, and bolt the transceiver into place using the supplied
short screws and flat washers.
Mobile Power Connections
To minimize voltage drop and avoid blowing the vehicle's fuses,
connect the supplied DC power cable
directly to the battery terminals. Do not attempt to defeat or
bypass the DC cable's fuse-it is there to
protect you, your transceiver, and your vehicle’s electrical
system.
Warning!
Never apply AC power to the power cable of the FT-1500M, nor DC
voltage greater than 15.2 Volts.
When replacing the fuse, only use a 15-A fast-blow type. Failure to
observe these safety precautions
will void the Limited Warranty on this product.
r Before connecting the transceiver, check the voltage at the
battery terminals while revving the
engine. If the voltage exceeds 15 Volts, adjust the vehicle's
voltage regulator before proceeding with
installation.
r Connect the RED power cable lead to the POSITIVE (+) battery
terminal, and the BLACK power
cable lead to the NEGATIVE (–) terminal. If you need to extend the
power cable, use #12 AWG or
larger insulated, stranded copper wire. Solder the splice
connections carefully, and wrap the
connections thoroughly with insulating electrical tape.
r Before connecting the cable to the transceiver, verify the
voltage and polarity of the voltage at the
transceiver end of the DC cable using a DC voltmeter. Now connect
the transceiver to the DC cable.
Mobile Speakers
The optional SP-7 External Speaker includes its own swivel-type
mounting bracket, and is available
from your Yaesu dealer.
Other external speakers may be used with the FT-1500M, if they
present the specified 4-ohm
impedance and are capable of handling the 3.5 Watts of audio output
supplied by the FT-1500M.
Base Station Installation
The FT-1500M is ideal for base station use as well as in mobile
installations. The FT-1500M is
specifically designed to integrate into your station easily, using
the information to follow as a
reference.
AC Power Supplies
Operation of the FT-1500M from an AC line requires a power source
capable of providing at least 10
Amps continuously at 13.8 Volts DC. The FP-1023A, FP-1025A, and
FP-1030A AC Power Supplies
are available from your Yaesu dealer to satisfy these requirements.
Other well-regulated power
supplies may be used, as well, if they meet the above voltage and
current specifications.
Use the DC power cable supplied with your transceiver for making
power connections to the power
supply. Connect the RED power cable lead to the POSITIVE (+) power
supply terminal, and connect
the BLACK power cable lead to the NEGATIVE (-) power supply
terminal.
Packet Radio Terminal Node Controller (TNC)
The FT-1500M provides a convenient rear-panel DATA jack for easy
connections to your TNC. This
connector is a standard mini-DIN connector.
The FT-1500M's DATA jack connections are optimized for the data
transmission and reception speed
in use. In accordance with industry standards, the signal levels,
impedances, and bandwidths are
significantly different on 9600 bps as opposed to 1200 bps. If your
TNC does not provide multiple
lines to accommodate such optimization, you may still be able to
utilize your TNC, if it is designed for
multiple-radio use, by connecting the TNC “Radio 1” port to the
1200 bps lines on the FT-1500M, and
the “Radio 2” port to the 9600 bps lines.
The pin connections of the Data connector are shown below.
Notes
?
?
?
?
?
?
Label
?
?
?
?
?
?
Pin
1
2
3
4
5
6
Note that 9600 bps packet transmit-deviation adjustment is very
critical to successful operation, and
can only be accomplished using a calibrated deviation meter (such
as that found on an FM Service
Monitor used in a communications service center). In most cases,
the Packet Data Input level (set via a
potentiometer inside the TNC) must be adjusted to provide a
deviation of ±2.75 kHz (±0.25 kHz).
Check with your packet node’s sysop if you have any questions about
the appropriate deviation level
for your network.
The setting of the 1200 bps Packet Data Input level is much less
critical, and satisfactory adjustment
to the optimum (±2.5 ~ ±3.5 kHz) deviation can usually be done “by
ear” by adjusting the TNC’s
1200 bps TX Audio Level potentiometer so that the outgoing packets
(as monitored on a separate
VHF or UHF receiver) are approximately the same level as (A) the
DTMF tones or (B) the 1750 Hz
Burst tone produced by the MH-???? microphone.
Typical connections to a TNC are shown below.
1200 bps Packet Setup
9600 bps Packet Setup
Finally, note that Menu (“PCKT”) allows you to enable or disable
the microphone during packet
operation. Normally, the default setting (“Microphone Disabled
during Packet TX”) is appropriate;
when the microprocessor detects PTT input from the Data connector,
the microphone will be disabled.
Basic Operation
Power On and Off
Press the PWR switch momentarily to turn the radio on.
To turn the radio off, press and hold in the PWR switch for one
second.
Adjusting the Volume Level
Rotate the VOL control to adjust the receiver volume. Clockwise
rotation increases the audio output
level.
Squelch Setup
The Squelch system is designed to keep the receiver quiet until a
signal is received. The Squelch
should be adjusted to the point where the background noise is just
silenced; any “higher” setting will
reduce the receiver’s sensitivity to weak signals.
To adjust the setting of the Squelch system:
1. Rotate the Main Dial to select a clear frequency (where no
signals are present).
2. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select “SQL.”
3. Press the [MHz] key momentarily, then rotate the Main Dial knob
to select the squelch threshold
level (OFF, or 1 to 15). While you are making this adjustment, you
will be able to hear the
background noise appear when the Squelch setting is too low. The
best sensitivity will be realized
when the Squelch is set to one number past the point where noise is
muted.
4. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
Transmitting
To transmit, simply close the PTT (Push To Talk) switch on the
microphone when the frequency is
clear. Hold the microphone approximately 25 mm (1”) from your
mouth, and speak into the
microphone in a normal voice level. When your transmission is
complete, release the PTT switch; the
transceiver will revert to the receive mode.
Tuning: The “DIAL” (VFO) Mode
This mode is used for selecting a frequency utilizing the Main Dial
knob and microphone [UP] and
[DWN] buttons allow the Variable Frequency Oscillator (VFO) to tune
in the selected step size. When
scanning in the VFO mode, the same steps are used as in manual
tuning.
Clockwise rotation of the Main Dial knob increases the operating
frequency, while counter-clockwise
rotation tunes toward a lower frequency.
To move frequency rapidly (in 1 MHz steps), press the [MHz] key
momentarily, then rotate the Main
Dial knob. The 1 MHz digit of the frequency display will blink
while “1 MHz Tuning” is enabled.
When you have selected the desired “1 MHz” frequency digit, press
the [MHz] key momentarily once
more, then resume normal tuning using the Main Dial knob.
Direct Keypad Frequency Entry
The keypad of the MH-?? DTMF Microphone may be used for direct
entry of the operating frequency.
It also may be used for recall of memory channels.
To enter a frequency from the MH-?? keypad:
1. Press the [D/MR] key, if necessary, to set the transceiver into
the VFO mode.
2. While receiving on any VFO frequency, enter the digits of the
desired frequency.
For example, to enter 146.520 MHz, press [1]–[4]–[6]–[5]–[2]–[0].
A high-pitched “beep” will confirm each key closure as you enter
the digits; the final “beep” will
be of longer duration, to confirm that the frequency entry is
complete.
3. The [#] key may be used to abbreviate the entry procedure.
Pressing the [#] key sets the current
digit and all following digits to “0” to complete the entry.
For example, to enter 146.500 MHz, press [1]–[4]–[6]–[5]–[#].
To enter 144.000 MHz, press [1]–[4]–[4]–[#].
Recalling memories is equally simple (see page ?? for details on
memory operation). You can recall a
memory from the MH-?? from any operating mode: VFO, Home, or
Memory.
1. Press the Channel Number you wish to recall, then press the [*]
key. For example, to recall
Memory Channel 2, press [2]–[*]. To recall Channel number 135,
press [1]–[3]–[5]–[*].
2. To return to the VFO mode, press the front panel’s [D/MR] key or
the microphone's [D] key.
3. If you are in the Memory Recall mode, you can enter a new
operating frequency directly, as
described above for VFO operation. However, you will observe that
a “MR” indicator will be
blinking appear at the left side of the display; this indicates
that you have switched to the “Memory
Tune” mode, which is described in detail on page ??.
Changing the Transmitter Power Level
Four power output levels are available on this transceiver: 5 watts
(Low 3), 10 watts (Low 2), 25
watts (Low 1) and 50 watts (High).
To change the power level, press the [REV] key to select one of
four power setting. These power
levels will be stored in memory registers, at the time of memory
storage (see page ?? for details on
Memory operation).
During transmission, the Bar Graph will deflect in the display,
according to the power output selected.
Transmitter Thermal Protection Sensor
Changing the Channel Steps
Tuning steps are factory preset to default increments which are
appropriate for the country to which
this radio is exported.
To change to another step size, use the following procedure:
1. Press and hold the [MHz] key for one second, then rotate the
Main Dial knob to select “STEP.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
the desired step size:
5.0/10.0/12.5/15.0/20.0/25.0/50.0 (kHz).
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
Keyboard Locking
In order to prevent accidental frequency change or inadvertent
transmission, various aspects of the FT-
1500M’s keys and switches may be locked out. The possible lockout
combinations are:
KEY: Just the front panel keys are locked out
DIAL: Just the front panel DIAL is locked out
K + D (KEY + DIAL) : Both the DIAL and Keys are locked out
PTT: The PTT switch is locked (TX not possible)
K + P (KEY + PTT) : Both the keys and PTT switch are locked out
D + P (DIAL + PTT) : Both the DIAL and PTT switch are locked out
ALL: All of the above are locked out
To lock out some or all of the keys:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select
“LOCK.”
2. Press the [MHz] key, then rotate the Main Dial knob to choose
between one of the locking
schemes as outlined above.
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
Repeater Operation
The FT-1500M includes a host of convenience features which makes
operation on amateur repeaters
both efficient and enjoyable.
Repeater Splits
This transceiver offers three methods of setting up split-frequency
operation on repeaters:
[1] Manual selection of preset repeater shifts;
[2] Automatic Repeater Shift (ARS), providing automatic activation
of repeater shifts within
designated repeater frequency subbands; and
[3] Independently stored transmit and receive frequencies
(typically not corresponding to established
repeater frequency shifts).
[1] Standard Repeater Shifts
The FT-1500M has been shipped ready for use on the repeater shift
typically used in your country. For
customers in the United States, for example, the standard repeater
shift will be 600 kHz, and the
direction of the shift will depend on the part of the band in which
you are operating.
To activate the standard shift manually:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select
“RPTR.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
the desired shift direction: ARS
(Automatic Repeater Shift), SHIFT– , SHIFT+, or OFF (Simplex).
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
With repeater shift activated, you can temporarily reverse the
transmit and receive frequencies by
pressing the front panel's [REV] key. Use this feature to display
the transmit frequency without
transmitting, and to check the strength of signals on a repeater
uplink frequency (so as to determine
whether or not a particular station is within “Simplex” range, for
example).
Changing the Default Repeater Shift
The repeater offset is usually set to 600 kHz from the factory. You
can change the offset by using
following procedure, if needed:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select
“SHIFT.”
2. Press the [MHz] key, then rotate the Main Dial knob to set the
desired offset. Note that the
resolution of the “standard” repeater shift is to the nearest 50
kHz multiple.
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
Note: Do not use the above procedure if you just want to operate on
one “odd split” frequency.
Use the “Independent Transmit/Receive Frequency” mode, as described
in section [3] on the next
page.
[2] Automatic Repeater Shift
The ARS (Automatic Repeater Shift) feature in the FT-1500M allows
easy and convenient repeater
operation by automatically activating the repeater shift function
whenever you tune to a standard
repeater sub-band. The ARS function is preset at the factory to
conform to the standards for the
country to which it is exported.
The ARS function is enabled at the factory. To disable it:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select “ARS.”
2. Press the [MHz] key, then rotate the Main Dial knob to change
the display to “OFF.”
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
To enable the ARS function again, select “ON” in step (2) above.
[3] Separate Transmit Frequency Memories
All memory channels can store independent receive and transmit
frequencies, to accommodate
occasional non-standard offsets with greater frequency resolution
than is available using the
“standard” shift feature.
Here is the procedure for storing an “odd split” frequency pair
into a memory. A full discussion of
memory channel storage and recall is found in the next section.
1. First store the receive (repeater output) frequency. In the VFO
mode, tune the transceiver to the
desired receive frequency. Now press and hold in the [D/MR] key for
one second.
2. Within five seconds of pressing the [D/MR] key, use the Main
Dial knob (or the microphone’s
[UP]/[DWN] buttons) to select the memory channel number on which
you wish to store the
frequency pair. If the memory register already has data stored in
it, the display will blink
“CHnnnUSD” where “nnn” is the channel number.
3. Now press the [D/MR] key for one second to store the receive
frequency into the selected
memory.
4. Next, store the transmit (repeater input) frequency. Since you
are still in the VFO mode, tune the
transceiver to the desired transmit frequency.
5. Now press and hold in the [D/MR] key for one second.
6. Press and hold the PTT switch, then press the [D/MR] key while
holding in the PTT switch. This
will not cause transmission, but rather it will instruct the
transceiver that you are programming a
separate transmit frequency into memory.
When you have finished the above procedure, press the [D/MR] key
momentarily. The channel
number will flash onto the display momentarily, to be followed by
the repeater downlink frequency. If
you press the PTT switch, you will observe the display changing to
indicate the repeater's uplink
frequency. Note also that the display shows “– +” in the upper
left-hand corner; this indicates that an
“odd” (non-standard) shift has been stored on this channel.
Advanced Operation
Supply Voltage Display
When you turn on the radio, the current DC supply voltage will be
indicated on the display for 2.5
second. After this interval, the display will resume its normal
indication of the operating frequency.
To view the supply voltage at any time during operation, use the
following procedure:
1. Press and hold the [MHz] key for one second, then rotate the
Main Dial knob to select “DC IN.”
2. Press the [MHz] key momentarily to display the current DC supply
voltage on the LCD.
3. Press and hold in the [MHz] key for one second to exit to normal
operation.
Keypad Beeper
A key/button beeper provides useful audible feedback whenever a
button is pressed. Each key and
button has a different beep pitch, and each function has a unique
beep combination.
If you want to turn the beeper off (or back on again):
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select “BEEP.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
the display to “OFF.”
3. Press and hold the [MHz] key for one second to save the new
setting and exit to normal operation.
Display Brightness
The FT-1500M display illumination has been specially engineered to
provide high visibility with
minimal disruption of your “night vision” while you are driving.
The brightness of the display is
manually adjustable, using the following procedure:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select
“DIMR.”
2. Press the [MHz] key, then rotate the Main Dial knob. You will
observe the brightness of the
display changing.
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
RF Squelch
A special “RF Squelch” feature is provided on this radio. This
feature allows you to set the squelch so
that only signals exceeding a certain S-meter level will open the
squelch.
To set up the RF squelch circuit for operation, use the following
procedure:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select
“RFSQL.”
2. Press the [MHz] key momentarily, then rotate the Main Dial knob
to select the desired signal
strength level for the squelch threshold (OFF, or S-1 to S-10).
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
Note: The receiver’s squelch will open based on the highest level
set by the two squelch systems
(Noise Squelch and RF Squelch). For example:
1. If the Noise Squelch (Menu #29) is set so that signals at a
level of S-3 will open the squelch, but
the RF Squelch (Menu #23) is set to “S-9,” the squelch will only
open on signals which are S-9
or stronger on the S-meter.
2. If the RF Squelch is set to “S-3,” but the Noise Squelch is set
to a high level which will only
pass signals which are Full Scale on the S-meter, the squelch will
only open on signals which are
Full Scale on the S-meter. In this case, the Noise Squelch
overrides the action of the RF Squelch.
Automatic Power-Off (APO) Feature
The “Automatic Power-Off” (APO) feature will turn the radio
completely off after a user-defined
period of PTT or key/button inactivity. If you do not press any
front panel keys or buttons, rotate the
Main Dial knob, use the microphone’s keys and buttons, or transmit,
and so long as the transceiver is
not scanning or engaged in priority monitoring, the radio will shut
itself off after the specified time
period. This feature is useful in minimizing battery drain in a
mobile installation if you forget to turn
the transceiver off when you leave your vehicle.
To activate the APO feature as follows:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select “APO.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
the desired “switch-off” time
(between 1 and 12 hours, or OFF).
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
Transmitter Time-Out Timer (TOT)
The “Time-Out Timer” (TOT) feature is designed to force the
transceiver into the “receive” mode
after a preset time period of continuous transmission (the default
is 6 minutes). This feature prevents
your transceiver from transmitting a “dead carrier” for a long
period of time in the event that the
microphone PTT switch is accidentally locked in the “TX” condition.
The Time-Out Timer’s “switch-to-receive” time may be adjusted, in
one minute increments, for any
period between 1 and 60 minutes.
To change the default (6 minute) time setting as follows:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select “TOT.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
the desired time interval (between 1
and 60 minutes, or OFF).
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
Programmable Microphone Keys (P1/P2/P3/P4)
Default FT-1500M key functions have been assigned (at the factory)
to the microphone’s [P1], [P2],
[P3], and [P4] buttons. These may be changed by the user, if you
wish to define another function for a
particular key or keys.
To change the assignment of a key's function:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to the Menu Item
# corresponding to the key to be assigned a function (18 PRG P1, 19
PRG P2, 20 PRG P3, or 21
PRG P4).
2. Press the [MHz] key momentarily, then rotate the Main Dial knob
to select the function you wish
Allows setting of the transmitter power level.
??
to assign to the key or button you selected in the previous step.
The available choices are:
MON Opens the Squelch to allow un-muted reception.
S. SRCH Initiates Smart Search scanning.
T. SRCH Initiates scanning for (unknown) CTCSS tone.
WX ??
SQ. TYP Selects CTCSS mode and frequency.
T. CALL Activates 1750 Hz Tone Burst.
SHIFT Selects Repeater Shift direction.
TX POWER
AN
3. Press the [MHz] key momentarily to lock in the new setting.
4. Rotate the Main Dial knob to select another programmable key or
button to modify, if desired,
from the remaining Menu items. Follow the procedure outlined above.
5. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
Tone Calling (1750 Hz)
If you own a non-European version of the FT-1500M, but plan on
visiting a country which requires a
1750 Hz tone for repeater access, you may set up the Programmable
key for 1750 Hz Tone operation.
See page ?? for details.
Weather Broadcast Reception
The FT-1500M includes a unique feature which allows reception of
weather broadcasts in the 160-
MHz frequency range. Ten standard Weather Broadcast channels are
pre-loaded into a special
memory bank.
To listen to a Weather Broadcast Channel:
1. Press the [P4] key to recall the Weather Broadcast channels.
2. Turn the Main Dial knob to select the desired Weather Broadcast
channel.
3. If you wish to check the other channels for activity by
scanning, just press and hold the [UP] or
[DWN] key for one second, or press the PTT switch.
4. To exit to normal operation, again press the [P4] key. Operation
will return to the VFO or
Memory channel you were operating on before you began Weather
Broadcast operation.
You can also append an alpha-numeric “Tag” (label) to a Weather
Broadcast channel. See page ??.
Frequency
161.775 MHz
163.275 MHz
Channel
WX 9
WX 10
Frequency
162.450 MHz
162.500 MHz
162.525 MHz
161.650 MHz
Channel
WX 5
WX 6
WX 7
WX 8
Frequency
162.550MHz
162.400 MHz
162.475 MHz
162.425 MHz
Channel
WX 1
WX 2
WX 3
WX 4
Tone Squelch Modes
Repeater systems often require an access signal for activation of
the repeater. These access tones are
often required so as to reduce false activation of the repeater by
random noises or other signals on the
band. Additionally, these systems can allow silent monitoring of
busy channels until a call directed to
your radio is received, offering less disruption to family
activities, etc.
CTCSS (Continuous Tone Coded Squelch System)
This system superimposes a continuous, subaudible tone on your
transmitted audio. When decoded at
the other station, the CTCSS signal triggers their squelch to open
and receive your transmission. Some
“closed” repeaters use this to limit access, or to prevent signals
intended for other repeaters (with the
same input frequency) in fringe areas from locking up the repeater.
There are 47 selectable CTCSS
tones provided in the FT-1500M.
To use CTCSS, both stations must be on the same frequency, and must
have selected the same CTCSS
tone.
To select and activate CTCSS operation:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select
“TONE.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
the desired squelch type from the
following:
m “ENC”(Encode) appears when the CTCSS tone generator is activated
for transmission only.
m “ENC/DEC” (Encode/Decode) appears when the CTCSS Tone Squelch is
activated for both TX
and RX (only signals “Encoded” with the matching tone will open
your radio’s squelch).
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
Now that you have selected the Tone Mode to be used, you need to
select the CTCSS tone, that you
and the other station have both agreed to use:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select “TN
FRQ.”
2. Press the [MHz] key, then rotate the Main Dial knob to choose
the desired CTCSS tone.
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
CTCSS settings may stored in any memory register at the time of
frequency programming. To change
a memorized tone or tone system, just recall the memory channel,
reset the tone or function, and store
the memory again. If you activate CTCSS on a PMS memory, it will be
active when that memory pair
is used to start PMS scanning or tuning.
Tone Search Scanning
In operating situations where you don’t know the CTCSS tone being
used by another station, you can
command the radio to listen to the incoming signal and scan in
search of the tone being used.
Before you begin the tone search, please check the (programmable)
setting of the microphone’s [P3]
button (Menu #20); it should be set to “T.SRCH” for proper
operation.
To scan for the CTCSS tone in use:
1. Set the radio up for the CTCSS operation.
2. Press the [P3] button on the microphone momentarily to start
scanning for the incoming CTCSS
tone.
3. When the radio detects the correct tone, it will halt on that
tone, and audio will be allowed to pass.
4. Press and hold in the [D/MR] key for one second; the CTCSS tone
detected will be stored as the
“current” tone, so it may be used for memory storage purposes.
It can be viewed by accessing Menu #33 (TN FRQ).
5. Press and hold in the [MHz] key for one second to exit to normal
operation.
CTCSS Bell Operation
CTCSS Bell Paging adds an alert ringer to CTCSS tone squelch
operation, for added convenience.
When you receive a call with a matching CTCSS tone, the ringer will
sound to alert you to the
presence of the incoming call.
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select
“BELL.”
2. Press the [MHz] key, then rotate the Main Dial knob to change
the display to “ON.”
3. To de-activate CTCSS Bell operation, select “OFF” in step 2
above.
Calls without a matching CTCSS tone will be ignored during CTCSS
Bell operation.
Note that other stations do not need to have the CTCSS Bell
function to call you; they can just use
standard CTCSS encoding.
When you reply to a CTCSS Bell call, you may want to turn off the
Bell function, or else the
transceiver will ring every time your squelch opens.
You can store the CTCSS Bell Paging function into a memory, along
with the CTCSS tone and
encode/decode state.
Memory Operation
The FT-1500M provides a wide variety of memory system resources.
These include:
m 120 “Standard” memory channels, numbered “1” through “120.”
m A Home channel, allowing storage and quick recall of one prime
frequency.
m Nine sets of band-edge memories also known as “Programming Memory
Scan” channels, labeled
“L1/U1” through “L9/U9”.
Memory Storage
To store a frequency into memory:
1. In the VFO mode, select the desired frequency, repeater shift,
CTCSS tone, and TX power level.
2. Press and hold in the [D/MR] key for one second. A memory number
(or letters and numbers) will
appear (blinking) on the display.
3. Within five seconds of pressing the [D/MR] key, use the Main
Dial knob or the microphone’s
[UP]/[DWN] buttons to select the desired memory for storage. If you
see an Asterisk (*) by any
channel number, it means that the channel currently has no data
written on it (i.e the channel is
“free”).
4. Press the [D/MR] key again, this time momentarily, to store the
displayed data into the selected
memory channel slot. The memory label will stop blinking, and the
display will now be blank,
except for a blinking digit at the left side of the display. If you
wish to append a name to the justmemorized
channel, move quickly to the next step.
Note: If the left digit quits blinking, this indicates that the
Alpha-Numeric Storage Timer has
expired. The frequency data will not be lost if this happens,
however.
Labeling Memories
1. While the right-most digit is still blinking in step (4) above,
rotate the Main Dial knob to select
the first character in the name you wish to store, then press the
[D/MR] key to move on to the next
character. Letters (both upper and lower case), numbers, and
symbols are available for storage.
2. Again rotate the Main Dial knob to select the desired number,
letter, or symbol, then press the
[D/MR] key to move on to the next character’s slot.
3. Repeat step (2) as many times as necessary to complete the name
tag for the memory, then press
If you wish to append a label to a memory after the Alpha-Numeric
Storage Timer has
and hold in the [D/MR] key for one second to save the A/N
(Alpha-Numeric) name entry and exit
to normal operation.
Note:
expired, first recall the memory channel (see below), then press
the [MHz] key for one second to enter
the Menu mode. Rotate the Main Dial to select Menu item #01 (ALPH),
then press the [MHz] key
momentarily. You will now be ready to begin with step 1 above.
Memory Recall
From the VFO mode, momentarily press the [D/MR] key once to
activate the “MR” (Memory Recall)
mode.
When more than one memory has been stored, use the Main Dial knob
to select a memory for
operation. Alternatively, microphone’s [UP] and [DWN] buttons may
be used to step or scan through
the available memories. When using the microphone's buttons, press
and immediately release the
button to move one step up or down; press and hold the [UP] or
[DWN] button for one second to begin
memory scanning.
While you are operating in the MR mode, the “MR” notation will
appear at the left side of the display.
Memory Recall from MH-?? Microphone
While operating in the VFO, Home Channel (see below), or Memory
Recall mode, the keypad of the
MH-?? may be used for direct recall of memory channels.
To do this, press the Channel Number you wish to recall, then press
the [*] key. For example, to recall
Memory Channel 5, press [5]–[*]. To recall Channel number 118,
press [1]–[1]–[8]–[*].
To Turn on the Alpha-Numeric Memory Name Display
If you are in the “MR” mode, press and hold the [A/N] key for one
second, to replace the frequency
display with the Alpha-Numeric Label.
HOME Channel Memory
A convenient one-touch “Home” channel memory is available to
simplify return to your most-oftenused
frequency. This memory does not appear in the regular memory bank,
to simplify operation.
To recall the Home channel while in the MR mode, just press the
[D/MR] key momentarily. From the
VFO mode, press [D/MR] twice. While you are operating on the Home
channel, an “HM” will appear
at the right side of the display.
The factory default frequency for the Home channel is 146.520 MHz.
You can re-program the Home
channel in a manner identical to that used for the regular
memories:
1. From the VFO mode, tune in the frequency you wish to store, and
set all repeater shifts and other
data just the way you do for “normal” memory channel storage.
2. Press and hold the [D/MR] key for one second, then rotate the
Main Dial knob to select
“HOME.”
3. Press the [D/MR] key momentarily to store the new Home channel.
4. At this point, the right-most digit will be blinking, as a
reminder that you can store an Alpha-
Numeric label to the Home channel. Use the A/N storage procedure
described previously.
Memory Offset Tuning
Once you have recalled a particular memory channel, you may tune
off that channel, as though you
were in the VFO mode.
1. With the FT-1500M in the “MR” mode, select the desired memory
channel.
2. Press the [MHz] key momentarily.
3. Now rotate the Main Dial knob, as desired, to tune to a new
frequency. This new frequency may
be stored in a new memory register, if you like, using the
procedures described earlier.
4. If you wish to return to the original memory frequency, press
the [D/MR] key momentarily. Any
offset tuning will be discarded, and the original memory contents
will appear on the display.
Masking Memories
With 138 total memories available, there frequently are situations
where you may desire to “Mask”
certain memorized frequencies. The procedure for deleting a channel
is quite simple:
1. Press and hold in the [D/MR] key for one second.
2. Rotate the Main Dial to select the channel to be “Masked”. Note
that Memory Channel 1 may not
be deleted, as it is the Priority Channel.
3. Press the [LOW] button. This will cause the display to shift to
Memory Channel 1, and the
previously-selected memory will be deleted.
4. To Unmask the hidden memory, repeat the above procedure: press
and hold in the [D/MR] key for
one second, rotate the Main Dial to select the masked memory's
number, then press [LOW] to
restore the memory channel’s data.
Memory Only Mode
Once memory channel programming has been completed, you may place
the radio in a “Memory-
Only” mode, whereby VFO and Home channel operation are impossible.
This may be particularly
useful during public-service events where a number of operators may
be using the radio for first time,
and ultimate simplicity of channel selection is desired.
To place the radio into the Memory-Only mode, turn it off. Now
press and hold in the [D/MR] key
while turning the radio on. The VFO and Home channel will now be
disabled.
To return to normal operation, repeat the above power-on procedure.
Scanning
The FT-1500M’s scanning capability provides the operator with many
convenient methods of rapid
frequency navigation.
Basic Scanner Operation
Before activating the scanner, make sure that the Squelch is set to
silence the background noise when
no signal is present. If noise is being heard, the scanner will not
function (because the radio will
“think” that it is on a “Busy” channel).
Scanning may be started or stopped using the microphone’s [UP] and
[DWN] buttons. The following
techniques are used during scanning operation:
1. Pressing and holding in either the [UP] or [DWN] button for one
second in the VFO mode will
cause upward or downward band scanning, respectively, to begin.
2. Pressing and holding in either the [UP] or [DWN] button for one
second in the Memory Recall
mode will cause memory channel scanning toward a higher- or
lower-numbered memory channel,
respectively.
3. Scanning pauses when a signal opens the squelch, and the decimal
point on the display will blink.
You can choose one of two scan-resume modes (described later).
4. To halt the scan manually, the easiest way is to push the PTT
switch on the microphone
momentarily (no transmission will occur while you are scanning).
The scan may also be halted manually by pressing the microphone’s
[UP] or [DWN] button, or the
[D/MR] key on the front panel of the radio.
Scan-Resume Options
Three scan-resume modes are available on the FT-1500M:
BUSY: In this mode, the scanner will remain halted for as long as
there is carrier present on
the channel; after the carrier drops at the end of the other
station’s transmission, the scanner
will resume.
5SEC: In this mode, the scanner will halt for five seconds only,
after which scanning will
resume (whether or not the other station is still transmitting).
HOLD: In this mode, the scanner will halt on a signal it
encounters. It will not restart
automatically; you must manually re-initiate scanning if you wish
to resume.
To change the scan-resume mode:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select
“SCAN.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
the desired scan-resume mode
(BUSY, 5SEC, or HOLD).
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
Memory Skip Scanning (MR Mode)
When you have some continuously-active channels (like Weather
broadcasts) in memories, you may
wish to skip them for scanning, but still have them available for
manual selection.
To select a memory to be skipped during scanning:
1. Recall the memory channel to be skipped. Note that Memory
Channel 1 may not be skipped, as it
is the Priority Channel.
2. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select “SKIP.”
3. Press the [MHz] key, then rotate the Main Dial knob to select
“SKIP.”
4. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
To re-enable a “Skipped” memory channel, select “STOP” in step (3)
above.
Temporary Memory Skip
If the scanner repeatedly stops on a channel due to temporary noise
or interference, you can
temporarily mark it to be skipped. The channel will be skipped
until you manually stop the scan (by
pressing the PTT switch, for example).
To skip a channel temporarily, press the [MHz] key momentarily
while the scanner has stopped on the
channel to be skipped. The scanner will instantaneously resume, and
that channel will not be scanned
during this scanning session. Note that Memory Channel 1 may not be
skipped, as it is the Priority
Channel.
Programmable (Band Limit) Memory Scan (PMS)
This feature allows you to set sub-band limits for either scanning
or manual VFO operation. For
example, you might wish to set up a limit (in North America) of
144.300 MHz to 148.000 MHz so as
to prevent encroachment into the SSB/CW “Weak Signal” portion of
the band below 144.300 MHz.
Here’s how to do this:
1. Using the techniques learned earlier, store (per the above
example) 144.300 MHz into Memory
Channel #L1 (the “L” designates the Lower sub-band limit).
2. Likewise, store 148.000 MHz into Memory Channel #U1 (the “U”
designates the Upper sub-band
limit).
3. With any of these memories recalled, press the [MHz] key
momentarily to activate the
Programmable Band-Scan Limits. The “PMS” notation will appear at
the left side of the display,
reminding you that you are using the Programmable Band Limits.
The frequencies stored in memories “L” and “U” will now serve as
tuning and scanning limits, thus
creating a tuning sub-band.
To cancel the sub-band limits and return to normal memory
operation, press the [D/MR] key
momentarily.
Note:
m If the frequency in memory channel “Lx” is equal to or greater
than the frequency stored in memory
channel “Ux,” you can not activate the PMS operation.
m Nine pairs of Band Limit memories, labeled L1/U1 through L9/U9
are available.
Band Edge Beeper
Smart Search Operation
The Smart Search feature allows you to load frequencies
automatically according to where activity is
encountered by your radio. When Smart Search is engaged, the
transceiver will search above and
below your current frequency, storing active frequencies as it goes
(without stopping on them even
momentarily); these frequencies are stored into a special Smart
Search memory bank, consisting of 31
memories (15 above the current frequency, 15 below the current
frequency, plus the current frequency
itself).
Two basic operating modes for Smart Search are available:
SINGLE: In this mode, the transceiver will sweep the current band
once in each direction starting on
the current frequency. All channels where activity is present will
be loaded into the Smart Search
memories; whether or not all 31 memories are filled, the search
will stop after one sweep in each
direction.
CONTINUE: In this mode, the transceiver will make one pass in each
direction as with One-
Shot searching; if all 31 channels are not filled after the first
sweep, however, the radio will continue
sweeping until they are all filled.
Setting the Smart Search Mode
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select
“S.SRCH.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
the desired Smart Search mode (see
above).
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
Storing Smart Search Memories
1. Press the [P2] key.*
2. The Smart Search process will now cause the radio to scan upward
on current band, loading
channels on which it encounters a signal strong enough to open the
squelch.
3. Depending on the mode you set for Smart Search operation (SINGLE
or CONTINUE), the Smart
Search scan will eventually terminate, and the LCD will revert to
Smart Search Memory Channel
4. To recall the Smart Search Memories just stored, rotate the Main
Dial knob or press the
0.
microphone’s [UP] or [DWN] key.
5. If you find particular channels which you wish to store into the
“regular” memory system, follow
the memory storage procedures described on page ??.
6. Press the [D/MR] key momentarily to exit the Smart Search mode.
Note that these memories are so-called “soft” memories; they will
be lost if you exit the Smart Search
mode or initiate a new Smart Search sweep.
* The (user-programmable) [P2] key is set at the factory for Smart
Search operation.
It may be assigned to one of the other programmable keys, if you
like. See page ??.
Priority Channel Scanning (Dual Watch)
The FT-1500M scanning features include a two-channel scanning
capability which allows you to
operate on a VFO or Memory channel, while periodically checking a
user-selectable Priority Channel
for activity.
Here is the procedure for activating Priority Channel Dual Watch
operation:
1. Press and hold in the [D/MR] key for one second, then rotate the
Main Dial knob to select
“Priority” Channel.
2. Press and hold in the [D/MR] key for one second.
3. Set the radio to the VFO mode or HOME channel by pressing the
[D/MR] key.
4. Press and hold in the [REV] key for one second, to start
Priority Channel Scanning (a small
“PRI” notation will appear on the LCD).
5. To cancel priority monitoring, press the [D/MR] key momentarily.
During priority monitoring, the displayed frequency will shift to
the priority memory briefly about
every five seconds, while the receiver checks for the presence of
a signal.
While no signal appears on the Priority memory (causing the squelch
to open), you can tune, transmit
and receive on the VFO, or select and operate on other memories;
however, you cannot scan (except
manually, one step at a time, using the microphone’s [UP] and [DWN]
buttons), as the scanning logic
circuits are already dedicated to the priority scanning activities.
Priority Revert Mode
During Priority channel operation (Dual Watch), a special feature
is available which will allow you to
move to the Priority Channel instantly, without waiting for
activity to appear on the Priority Channel.
When this feature is enabled, and Priority monitoring is engaged,
just press the microphone’s PTT
button. Operation will instantly revert to the Priority Channel.
To enable Priority Revert operation:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select
“RVRT.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
“ON.”
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
To disable Priority Revert operation, select “OFF” in step (2)
above.
DTMF Operation
Manual DTMF Tone Generation
You can generate DTMF tones during transmission manually.
1. Press the PTT switch to begin transmission.
2. While transmitting, press the desired numbers on the keypad.
4. When you have sent all the digits desired, release the PTT key.
DTMF Autodialer
Eight DTMF Autodialer memories are available on the FT-1500M. These
DTMF Autodialer
memories can store up to 16 digits of a telephone number for,
repeater autopatch or other uses.
To load DTMF Autodialer memories, use following procedure:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select “DT
MEM.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
the DTMF Autodialer memory
channel number into which you wish store a telephone number (“1” to
“8”).
3. Press the [D/MR] key momentarily.
4. Rotate the Main Dial knob to select the first digit of the
telephone number you wish to store.
5. When you have selected the correct digit, press the [D/MR] key
momentarily.
Now rotate the Main Dial knob to select the second of the 16
available numbers in the current
DTMF Autodialer memory register.
6. Repeat this procedure for each digit in the telephone number.
7. When entry of all digits is complete, press and hold the the
[D/MR] key for one second to save the
new setting. If you wish to store another DTMF string, rotate the
Main Dial knob to select another
DTMF Memory register, then repeat steps (3) through (6) above.
8. When all required DTMF memories are filled to your satisfaction,
press and hold in the [MHz]
key for one second to save the new settings and exit to normal
operation.
To transmit the memorized telephone number, use the following
procedure:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select
“DTMF.”
2. Now press the [MHz] key momentarily to enable selection of the
Autodialer Memory.
3. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select “DT
MEM.”
4. Now press the [MHz] key momentarily to enable selection of the
Autodialer Memory.
5. Rotate the Main Dial knob to select the DTMF Autodialer Memory
channel to be transmitted.
6. Press and hold in the PTT switch.
7. While still holding the PTT switch in, press the [MHz] key
momentarily to transmit the tone
string.
Once you have pressed the [MHz] button above step, you can release
the PTT switch, as Autodialer
transmits the whole DTMF string automatically.
The speed at which the DTMF digits are sent can be changed. Two
speed levels are available: Low
(10 digits per second) and High (20 digits per second: default).
To toggle between Low and High speed, use the following procedure:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select “DT
SPD.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
the desired speed: “50 ms” (High
speed) or “100 ms” (Low speed).
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
You can also set a longer delay between the time you press the
[MHz] key (with PTT pressed) and the
first DTMF digit is sent.
To set a delay time, use the following procedure:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select “DT
DLY.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
the desired speed
(50/250/450/750/1000 ms).
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to the normal
operation.
Interface of Packet TNCs & Reset
The FT-1500M provides a convenient rear-panel DATA jack for easy
TNC interconnections, Refer to
the graphic and table for pin-out connections.
Data rate selection (1200/9600 bps) can be selected via Menu “P
RATE.”
Normally, the microphone will be cut off during packet
transmission, so as to avoid interference to the
data stream by voice input. However, this protection feature can be
disabled, if you have some reason
to want the microphone to be active during packet transmission.
To re-activate the microphone during packet transmission:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select
“PCKT.”
2. Press the [MHz] key, then rotate the Main Dial knob to select
“MIC ON.”
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
To disable the microphone during packet transmission (the typical
configuration), select “MIC OFF”
in step 2 above.
Packet operating procedures are governed by the software used by
your computer and TNC. Consult
the documentation accompanying the software for details on packet
operation.
FM Bandwidth & Mic Gain Control
You can reduce the microphone input level and transmitter bandwidth
when operating on tightlyclustered
frequencies (channel spacing of 12.5- or 15-kHz). This will reduce
the transmitter deviation,
thus minimizing interference to other users.
To reduce the microphone input level:
1. Press and hold in the [MHz] key for one second, then rotate the
Main Dial knob to select “W/N
DV.”
2. Press the [MHz] key, then rotate the Main Dial knob to change
the display to “NARROW.”
3. Press and hold in the [MHz] key for one second to save the new
setting and exit to normal
operation.
To restore the normal (higher) microphone input level and normal
(15 kHz) receiver bandwidth, select
“WIDE” in step 2 above.
Microprocessor Resetting
To perform a CPU master reset for all memories and Menu settings,
press the [LOW], and [D/MR]
keys while turning the transceiver on.
Set Mode Resetting
To reset all Menu settings to their factory defaults, press the
[REV] key and [D/MR] buttons while
turning the transceiver on.
Cloning
You can transfer all data stored in one transceiver to another set
by utilizing the handy “Cloning”
feature. This requires a user-constructed cloning cable which
connects the MIC jacks on the two
transceivers as shown below.
To clone from one transceiver to another, use the following
procedure:
1. Insert the Clone Cable into the MIC jack of each transceiver.
2. Turn both transceivers off, then press and hold in the [LOW] key
on each radio while turning the
power on again. The “CLN” notation will appear on the display.
3. On the “destination” radio, press the [D/MR] button.
4. Now, on the “source” radio, press the [MHz] key.
5. If there is a problem during the cloning process, “CLN ERR” will
be displayed. Check your cable
connections and try again.
6. If cloning is successful, turn the “destination” radio off. Now
turn the “source” radio off.
Remove the clone cable. Channel and operating data for both radios
are now identical. They both may
be turned on now for normal operation.
Set Mode
The FT-1500M’s Menu system allows a number of transceiver operating
parameters to be customconfigured
for your operating requirements.
The Menu is easy to activate and set, using the following
procedure:
1. Press and hold in the [MHz] key for one second.
2. Rotate the Main Dial knob to select the Menu item to be
adjusted.
3. Press the [MHz] key, then rotate the Main Dial knob to adjust
the status or value of the Menu
item.
4. After completing your adjustment, press and hold in the [MHz]
key for one second to save the
new setting and exit to normal operation.
Menu items are conveniently arranged in alphabetical order.
Menu Selection Summary
Set Mode Details
Set Item [ALPH]
Function: Programming an Alpha/Numeric label for a memory.
See page ?? for details.
Set Item [APO]
Function: Enable/Disable the Automatic Power Off feature.
Available Values: 1 ~ 12 Hours, or OFF
Default: OFF
Set Item [ARS]
Function: Enable/Disable the Automatic Repeater Shift function.
Available Values: ON/OFF
Default: ON
Set Item [BEEP]
Function: Enable/Disable the key/button beeper.
Available Values: ON/OFF
Default Setting: ON
Set Item [BELL]
Function: Enable/Disable the CTCSS Bell Paging feature.
Available Values: ON/OFF
Default Setting: OFF
Set Item [CH NUM]
Function: Enable/Disable the momentary display of the Memory
Channel Number as the Main Dial
knob is rotated.
Available Values: ON/OFF
Default Setting: OFF
Set Item [CK SFT]
Function: Shifting of CPU clock frequency..
Available Values: ON/OFF
Default Setting: OFF
Set Item [DC IN]
Indicate the Supply Voltage
Set Item [DIMR]
Function: Setting of the front panel display’s illumination level.
Available Values: 1 ~ 10 or OFF
Default Setting: 10
Set Item [DTMF]
Set Item [DT DLY]
Function: Setting of the DTMF Autodialer Delay Time
Available Values: 50/250/450/750/1000 ms.
Default Setting: 450 ms.
Set Item [DT MEM]
Function: Loading of the DTMF Autodialer Memories. See page ??.
Set Item [DT SPD]
Function: Setting of the DTMF Autodialer Sending Speed
Available Values: 50/100 ms.
Default Setting: 50 ms (high speed)
Set Item [EDG BP]
Function: Enable/Disable the Band-edge beeper while scanning.
Available Values: ON/OFF
Default Setting: OFF
Set Item [LOCK]
Function: Enable/Disable the key/button Lock
Available Values: KL/DL/K+D/PL/K+P/D+P/ALL/OFF
Default Setting: OFF
Set Item [PCKT]
Function: Enable/Disable the Microphone during Packet transmission.
Available Values: Mic ON/Mic OFF
Default Setting: Mic OFF
Set Item [P RATE]
Function: Set the transceiver’s circuitry for the Packet baud rate
to be used.
Available Values: 1200/9600 bps
Default Setting: 1200
Set Item [PRG P1]
Function: Programming the function assigned to microphone key P1
Available Values: MON/S.SRCH/T.SRCH/WX/SQ.TYP/T.CALL/SHIFT/TX
POWER/AN
Default Setting: MON (Squelch OFF)
Set Item [PRG P2]
Function: Programming the function assigned to microphone key P2
Available Values: MON/S.SRCH/T.SRCH/WX/SQ.TYP/T.CALL/SHIFT/TX
POWER/AN
Default Setting: S.SRCH (Smart Search)
Set Item [PRG P3]
Function: Programming the function assigned to microphone key P3
Available Values: MON/S.SRCH/T.SRCH/WX/SQ.TYP/T.CALL/SHIFT/TX
POWER/AN
Default Setting: T.SRCH (Tone Search)
Set Item [PRG P4]
Function: Programming the function assigned to microphone key P4
Available Values: MON/S.SRCH/T.SRCH/WX/SQ.TYP/T.CALL/SHIFT/TX
POWER/AN
Default Setting: WX (Weather Channel)
Set Item [REV/HM]
Function: Select the [REV] key function..
Available Values: REV/HOME
Default Setting: REV
Set Item [RF SQL]
Function: Adjust the RF Squelch threshold level.
Available Values: OFF/S-1 to S-10
WIDE (±5 kHz Deviation, 15 kHz bandwidth)
Default Setting: OFF
Set Item [RPTER]
Function: Enable/Disable the Automatic Repeater Shift feature and
Setting of the Repeater Shift
Direction
Available Values: ARS/Shift -/Shift +/OFF
Default Setting: ARS
Set Item [RVRT]
Function: Enable/Disable the “Priority Channel Revert” feature
Available Values: OFF/ON
Default Setting: OFF
Set Item [SCAN]
Function: Select the Scan Resume mode.
Available Values: BUSY/5SEC/HOLD
Default Setting: BUSY
Set Item [SHIFT]
Function: Set the magnitude of the Repeater Shift
Available Values: 0.00 ~ 99.95 MHz (only shifts of less than 4 MHz
will work)
Default Setting: 600 kHz
Set Item [SKIP]
Function: Enable/Disable Skipping of a channel during scanning.
Available Values: SKIP/STOP
Default Setting: STOP (Stop on busy channel)
Set Item [SQL]
Function: Set the Squelch threshold
Available Values: OFF/1 ~ 15 (arbitrary scale)
Default Setting: 1
Set Item [STEP]
Function: Setting of the synthesizer steps used in VFO/Memory Tune
operation.
Available Values: 5/10/12.5/15/20/25/50 kHz per step
Default Setting: 5 kHz
Set Item [S.SRCH]
Function: Select the Smart Search Sweep mode.
Available Values: Single/Continue
Default Setting: Single
Set Item [TONE]
Function: Select the CTCSS mode.
Available Values: OFF, T, TSQ
Default Setting: OFF
Set Item [TN FRQ]
Function: Setting of the CTCSS Tone Frequency.
Available Values: 39 standard CTCSS Tones
Default Setting: 100.0 Hz
Set Item [TOT]
Function: Set the time-out limit for the Time-Out Timer
Available Values: 1 ~ 60 minutes, or OFF
Default Setting: 6 minutes
Set Item [W/N DV]
Function: Reduction of the Microphone Gain/Deviation and receiver
bandwidth
Available Values: WIDE/NARROW
Default Setting:

.

Disclaimer: The information on this site is provided as a public service to the blind and visually handicapped community. While we have done our best to ensure the information provided is accurate, please realize the use of any information on this site is solely at your discretion and we take no responsibility for use or attempted use of this information.