ICanWorkThisThing.com

Click here to download

DUAL BAND TRANSCEIVER

FT-60R

OPERATING MANUAL

VERTEX STANDARD CO., LTD.

4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan

VERTEX STANDARD

US Headquarters

10900 Walker Street, Cypress, CA 90630, U.S.A.

YAESU EUROPE B.V.

P.O. Box 75525, 1118 ZN Schiphol, The Netherlands

YAESU UK LTD.

Unit 12, Sun Valley Business Park, Winnall Close

Winchester, Hampshire, SO23 0LB, U.K.

VERTEX STANDARD HK LTD.

Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,

Kwun Tong, Kowloon, Hong Kong

Contents

General Description ......................................... 1

Accessories & Options ..................................... 2

Controls & Connections .................................. 3

Top & Front Panel .......................................... 3

LCD ................................................................ 4

Side Panel ....................................................... 5

Keypad ........................................................... 6

Installation of Accessories ............................... 8

Antenna Installation ....................................... 8

Installation of FNB-83 Battery Pack ............. 8

Battery Charging ............................................ 9

Low Battery Indication ................................ 10

Installation of FBA-25A Battery Case ......... 10

Interface of Packet TNCs .............................. 11

Operation ........................................................ 12

Switching Power On and Off ....................... 12

Adjusting the Audio Volume Level and

Squelch Setting ....................................... 12

Selecting the Operating Band ...................... 13

Frequency Navigation .................................. 13

Transmission ................................................ 15

Advanced Operation ...................................... 16

Keyboard Locking ........................................ 16

Keypad/LCD Illumination ........................... 17

Disabling the Keypad Beeper ...................... 17

RF Squelch ................................................... 18

Checking the Battery Voltage ...................... 18

Repeater Operation ........................................ 19

Repeater Shifts ............................................. 19

Automatic Repeater Shift (ARS) ................. 19

Manual Repeater Shift Activation ............... 20

CTCSS/DCS Operation ................................. 22

CTCSS Operation ........................................ 22

DCS Operation ............................................. 23

Tone Search Scanning ................................. 24

CTCSS/DCS Bell Operation ........................ 25

Split Tone Operation .................................... 25

Tone Calling (1750 Hz) ............................... 26

Memory Mode ................................................ 28

Memory Storage ........................................... 28

Storing Independent

Transmit Frequencies (“Odd Split”) ........ 28

Memory Recall ............................................. 29

HOME Channel Memory ............................. 29

Labeling Memories ...................................... 30

Memory Offset Tuning ................................ 31

Deleting Memories ....................................... 32

Moving Memory Data to the VFO ............... 32

Memory Bank Operation ............................. 33

Memory Only Mode ..................................... 34

Weather Broadcast Channels ....................... 34

Scanning .......................................................... 35

VFO Scanning .............................................. 35

Manual VFO Scan ................................... 35

Programmed VFO Scan ........................... 36

Memory Scanning ........................................ 37

How to Skip (Omit) a Channel

during Memory Scan Operation .............. 37

Preferential Memory Scan ....................... 38

Memory Bank Scan ................................. 39

Weather Alert Scan ...................................... 39

Programmable (Band Limit) Memory Scan

(PMS) ........................................................... 40

“Priority Channel” Scanning

(Dual Watch) ................................................ 41

Automatic Lamp Illumination

on Scan Stop ................................................ 43

Band Edge Beeper ........................................ 43

EPCS (Enhanced Paging & Code Squelch) ............. 44

Storing the CTCSS Tone Pairs

for EPCS Operation ..................................... 44

Activating the Enhanced Paging &

Code Squelch System .................................. 45

Paging Answer Back .................................... 45

Emergency Feature ........................................ 46

Emergency Channel Operation .................... 46

Emergency Automatic ID (EAI) Feature ..... 46

Smart Search Operation ................................ 48

Internet Connection Feature ......................... 49

ARTS (Automatic Range Transponder System) ....... 51

DTMF Operation ........................................... 54

Miscellaneous Settings ................................... 56

Password ...................................................... 56

Programming the Key Assignment .............. 57

Changing the Channel Steps ........................ 57

Changing the Receiving Mode .................... 58

Receive Battery Saver Setup ........................ 59

TX Battery Saver .......................................... 59

Disabling the TX/BUSY Indicator .............. 60

Automatic Power-Off (APO) Feature .......... 60

Transmitter Time-Out Timer (TOT) ............ 61

Busy Channel Lock-Out (BCLO) ................ 61

Mono Band Operation ................................. 62

Changing the TX Deviation Level ............... 62

DCS Code Inversion .................................... 63

Reset Procedures ............................................ 64

Cloning ............................................................ 65

Set Mode .......................................................... 66

Specifications .................................................. 79

“AUTO” Mode Preset Operating Parameters .... 80

FT-60R OPERATING MANUAL 1

GENERAL DESCRIPTION

The FT-60R is a dual band FM transceiver with extensive receive frequency coverage,

providing local-area two-way amateur communications along with unmatched monitoring

capability.

The FT-60R’s small size allows you to take it anywhere - hiking, skiing, or while walking

around town - and its operating flexibility brings the user many avenues of operating enjoyment.

Its incredibly tiny FNB-83 Rechargeable Nickel-Metal Hydride Battery Pack

provides up to 5 Watts of transmit power on 144 MHz and 430 MHz Amateur Bands.

Besides 144- and 430-MHz transceive operation, the FT-60R provides receive coverage

of the VHF and UHF TV bands, the VHF AM aircraft band, and a wide range of commercial

and public safety frequencies!

New and exciting features of the FT-60R are the Emergency Automatic ID (EAI) function,

that will automatically cause your FT-60R to transmit your callsign and engage your rig’s

microphone, even if you are disabled and unable

to press the PTT switch; Enhanced Paging and

Code Squelch (EPCS), that allows you to page a

particular station and only receive calls from that

station, if desired; and a security Password feature,

that will allow you to turn on and operate

your transceiver only after you enter your Password.

Additional features include a convenient access

key for Vertex Standard’s WIRES™ (Wide-coverage

Internet Repeater Enhancement System), a

transmit Time-Out Timer (TOT), Automatic

Power-Off (APO), Automatic Repeater Shift

(ARS), Yaesu’s exclusive ARTS™ (Auto-Range

Transponder System) which “beeps” the user when

you move out of communications range with another

ARTS™ equipped station, plus provision for

reduction of the TX deviation in areas of high channel

congestion. And an RF squelch circuit allows

the owner to set the squelch to open at a programmable

setting of the S-Meter, thus reducing guesswork

in setting the squelch threshold.

We appreciate your purchase of the FT-60R, and

encourage you to read this manual thoroughly, so

as to learn about the many exciting features of your

exciting new Yaesu hand-held transceiver!

ACCESSORIES & OPTION S

SUPPLIED ACCESSORIES

FNB-83

7.2 V, 1,400 mAh

Rechargeable Nickel-Metal Hydride Battery Pack

NC-88B/C.

Overnight Battery Charger (10-Hour)

Belt Clip

Antenna

Operating Manual

Warranty Card

AVAILABLE OPTIONS

FNB-83 7.2 V, 1,400 mAh

Rechargeable Nickel-Metal Hydride Battery Pack

FBA-25A Compact Dry Battery Case for 6 AA-size cells

CD-29B/C.

Rapid Charger (1.5-Hour)

NC-88B/C.

Overnight Battery Charger (10-Hours)

CN-3

BNC-to-SMA Adapter

CT-27

Cloning Cable

CT-44

Microphone Adapter

E-DC-5B

DC Cable with Cigarette-Lighter Adapter

E-DC-6

DC Cable; plug and wire only

MH-34B4B

Speaker/Microphone

MH-37A4B

Ear piece/Microphone

VC-25

VOX Headset

.:“B” suffix is for use with 100-120 VAC, “C” suffix is for use with 230-240 VAC.

Availability of accessories may vary. Some accessories are supplied as standard per local

requirements, while others may be unavailable in some regions. Consult your Yaesu dealer

for details regarding these and any newly-available options. Connection of any non-Yaesuapproved

accessory, should it cause damage, may void the Limited Warranty on this apparatus.

FT-60R OPERATING MANUAL

FT-60R OPERATING MANUAL 3

CONTROL & CONNECTIONS (TOP & FRONT PANEL)

. Antenna Jack

Connect the supplied rubber flex antenna (or another antenna presenting a 50-Ohm

impedance) here.

. VOL/PWR Knob

Turn this control clockwise to turn the radio on and to

increase the volume. Counter-clockwise rotation into

the click-stop will turn the radio off.

. TX/BUSY Indicator Lamp

This indicator glows green when the squelch opens,

and turns red during transmit.

. DIAL Knob

This (inner) 20-position detented rotary switch is used for setting the operating frequency,

and also is used for menu selections and other adjustments.

. SQL Knob

This (outer) control is used to silence background

noise on the receiver. It should be advanced

clockwise just to the point where the

noise is silenced (and the green “BUSY” indicator

turns off).

. LCD (Liquid Crystal Display)

The display shows current operating condition,

as indicated on the next page.

. Speaker

The internal speaker is located here.

. Microphone

The internal microphone is located here.

Keypad

These 16 keys select many of most important

operating features on the FT-60R. The functions

of the keys are described in detail on the

pages to follow.

. ....

CONTROL & CONNECTIONS (LCD )

S- & PO Meter

Repeater Shift Direction

CTCSS/DSC Operation

Battery Saver Active

Dual Watch Active

Memory Channel Number

Skip Memory Channel Automatic Power-Off

or Preferential Memory Active

Channel

Internet Connection

Priority Channel

Feature Active

Memory Bank Active

Bell Alerm Active

Operating Mode

Operating Frequency

Secondary Keypad

Battery Indicator

Active

Key Lock Active

Low TX Power Selected

FT-60R OPERATING MANUAL

CONTROL & CONNECTIONS (SIDE PANEL)

PTT (Push To Talk) Switch

Press this switch to transmit, and release it (to receive) after your transmission is completed.

MONI Switch

Pressing this switch disables the noise squelching action, allowing you to hear very

weak signals near the background noise level temporarily.

Press the [F/W] key on the keypad first, then press this switch to “open” the squelch

continuously. Press this switch again to resume normal (quiet) monitoring.

LAMP Switch

Pressing this switch illuminates the LCD and keypad for five seconds, after which the

back-lighting will automatically turn off.

Press the [F/W] key on the keypad first, then press this switch to activate the backlighting

lamp continuously. To turn the lamp off, press this switch again.

You can change the primary (press key) function of this switch, if you prefer. See page

17 for details.

MIC/SP Jack

This four-conductor

miniature jack provides

connection

points for microphone

audio, earphone audio,

PTT, and ground.

EXT DC Jack

This coaxial DC jack

allows connection to

an external DC power

source (6-16V DC).

The center pin of this

jack is the Positive (+)

connection.

MIC/SPEXTDC

FT-60R OPERATING MANUAL

CONTROL & CONNECTIONS (KEYPAD)

Primary Function

(PRESS KEY)

Frequency entry digit “1” Frequency entry digit “2”

Secondary Function

(PRESS

[F/W] + KEY)

Activates the CTCSS or DCS

Operation

Selects the CTCSS tone or DCS

code number

Third Function

(PRESS & HOLD KEY)

Recalls the “Weather” broadcast

channel bank

Activates the ARTS feature

Primary Function

(PRESS KEY)

Frequency entry digit “4” Frequency entry digit “5”

Secondary Function

(PRESS

[F/W] + KEY)

Selects the direction of the uplink

frequency shift (either “–,” “+,” or

“simplex”) during repeater operation

Selects the CTCSS/DCS Bell ringer

repetitions

Third Function

(PRESS & HOLD KEY)

Activates the EMERGENCY

function

None

.1 .1

Primary Function

(PRESS KEY)

Frequency entry digit “7” Frequency entry digit “8”

Secondary Function

(PRESS

[F/W] + KEY)

Activates the EPCS (Enhanced

Paging & Code Squelch) feature

Selects the Memory Scan “Skip”

channel-selection mode

Third Function

(PRESS & HOLD KEY)

None None

Primary Function

(PRESS KEY)

Switches the frequency control

between the VFO and Memory

Systems

Activates the Internet Connection

feature

Frequency entry digit “0”

Secondary Function

(PRESS

[F/W] + KEY)

Activates the Priority (Dual Watch)

function

Engages the Set (Menu) Mode

Third Function

(PRESS & HOLD KEY)

Starts the programmable scanner

upward (toward a higher frequency

or a higher channel number)

Enables Internet access code

selection

.1: You can program the secondary (press [F/W] key +) function of the key to another function, if

desired. See page 57 for details.

FT-60R OPERATING MANUAL

CONTROL & CONNECTIONS (KEYPAD)

Primary Function

(PRESS KEY)

Frequency entry digit “3”

Increases the VFO frequency by

one step or moves the memory

channel to the next-highest channel

Secondary Function

(PRESS

[F/W] + KEY)

Selects the desired transmit power

output level

Tunes the VFO frequency upward

in 1 MHz steps

Third Function

(PRESS & HOLD KEY)

Activates the Smart Search feature

Starts the scanner upward

(toward a higher frequency or

a higher channel number)

Primary Function

(PRESS KEY)

Frequency entry digit “6”

Decreases the VFO frequency by

one step or moves the memory

channel to the next-lowest channel

Secondary Function

(PRESS

[F/W] + KEY)

Activates the Key Lockout feature

Tunes the VFO frequency downward

in 1 MHz steps

Third Function

(PRESS & HOLD KEY)

Activates the Key Lockout feature

Starts the scanner downward

(toward a lower frequency or a

lower channel number)

Primary Function

(PRESS KEY)

Frequency entry digit “9”

Reverses the transmit and receive

frequencies while working through

a repeater

Secondary Function

(PRESS

[F/W] + KEY) Selects the DTMF mode

Switches to the “Home” (favorite

frequency) Channel

Third Function

(PRESS & HOLD KEY)

None None

Primary Function

(PRESS KEY)

Moves operation to the next-

highest frequency band while in the

VFO mode

Activates the “Secondary” key

function

Secondary Function

(PRESS

[F/W] + KEY)

Activates the “Memory “Tune” mode

while in the Memory Recall mode

Moves operation to the next-lowest frequency band

Disables the “Secondary” key

function

Third Function

(PRESS & HOLD KEY)

Selects the bandwidth for the

programmable scanner while in the

VFO mode

Activates the “Memory Write” mode

(for memory channel storage)

.2: You can exchange the function between primary (press key) function and secondary (press [F/W]

key +) function, if desired. See page 74 for details.

FT-60R OPERATING MANUAL

INSTALLATION OF ACCESSORIES

ANTENNA INSTALLATION

The supplied antenna provides good results over the entire frequency

range of the transceiver. However, for enhanced reception

on certain non-Amateur frequencies, you may wish to connect

an antenna designed specifically for that frequency range,

as the supplied antenna is necessarily a compromise outside the

Amateur bands, and cannot be expected to provide high performance

at all frequencies.

To install the supplied antenna, hold the bottom end of the antenna,

then screw it onto the mating connector on the transceiver

until it is snug. Do not over-tighten by use of extreme force.

Notes:

Never transmit without having an antenna connected.

When installing the supplied antenna, never hold the upper part of the antenna while

screwing it onto the mating connector on the transceiver.

If using an external antenna for transmission, ensure that the SWR presented to the

transceiver is 1.5:1 or lower, to avoid excessive feedline loss.

INSTALLATION

OF FNB-83 BATTERY PACK

The FNB-83 is a high-performance Ni-MH battery providing high capacity in a compact

package. Under normal use, the FNB-83 may be used for approximately 300 charge cycles,

after which operating time may be expected to decrease. If you have an old battery pack

which is displaying capacity which has become diminished, you should replace the pack

with a new one.

Installation of the battery is easy and quick:

Insert the battery pack into the battery compartment on the back of the

with a “Click.”

To remove the

battery, turn the

radio off and remove

any protective

cases.

Open the Bat-

radio while tilting the Belt Clip outward, then close the

Battery Pack Latch until it locks in place

Install the Battery Pack

Close the Battery Pack Latch

MIC/SPEXTDC

tery Pack Latch

on the bottom of the radio, then slide the battery downward and out from the radio

while tilting the Belt Clip out of the way.

FT-60R OPERATING MANUAL

FT-60R OPERATING MANUAL 9

BATTERY CHARGING

If the battery has never been used, or its charge is depleted, it may be charged by connecting

the NC-88 Overnight Battery Charger, as shown in the illustration, to the EXT DC

jack. If only 12 ~ 16 Volt DC power is available, the optional E-DC-5B DC Adapter (with

its cigarette lighter plug) may also be used for charging the battery.

A fully-discharged pack will be charged completely in 10 hours. Disconnect the NC-88

from the EXT DC jack and the AC line outlet.

Important Note

. The NC-88 is not designed to power the transceiver for operation (reception or

transmission).

. Do not leave the NC-88 connected to the transceiver for continuous periods in excess

of 24 hours. Long term overcharging can degrade the Ni-MH battery pack and

significantly shorten its useful life.

. Please be advised that the NC-88 may contribute noise to TV and radio reception in

the immediate vicinity, so we do not recommend its use adjacent to such devices.

INSTALLATION OF ACCESSORIES

EXT DC jack

AC line outlet

INSTALLATION OF ACCESSORIE S

LOW BATTERY INDICATION

As your battery discharges during use, the voltage will gradually become lower. When

the battery voltage is becoming too low for reliable operation,

the “

” icon will blink on the LCD display, indicating that the

battery pack must be recharged before further use.

Avoid recharging Ni-MH batteries before the “ ” indicator is observed, as this can

degrade the charge capacity of your Ni-MH battery pack.

INSTALLATION

OF FBA-25A ALKALINE BATTERY CASE

(OPTION)

The optional FBA-25A Battery Case allows operation of the FT-60R using six “AA” size

Alkaline batteries.

When installing batteries, insert the (–) end first, then press in the (+) end so the battery

snaps into place. Always replace all six batteries at the same time, paying attention to the

polarity indicated inside the case.

The FBA-25A must not be used with rechargeable cells. The FBA-25A does not contain

the thermal and over-current protection circuits (provided in the “FNB” series of Ni-MH

Battery Packs) required when utilizing Ni-Cd and Ni-MH cells.

Note that the power output and battery life will be much shorter when using Alkaline AA

cells. They should be considered an emergency backup power source only, for this reason.

FT-60R OPERATING MANUAL

FT-60R OPERATING MANUAL 11

The FT-60R may be used for Packet operation, using the optional CT-44 microphone

adapter (available from your Yaesu dealer) for easy interconnection to commonly-available

connectors wired to your TNC. You may also build your own cable, using a fourconductor

miniature phone plug, per the diagram below.

The audio level from the receiver to the TNC may be adjusted by using the VOL knob, as

with voice operation. The input level to the FT-60R from the TNC should be adjusted at

the TNC side; the optimum input voltage is approximately 5 mV at 2000 Ohms.

Be sure to turn the transceiver and TNC off before connecting the cables, so as to prevent

voltage spikes from possibly damaging your transceiver.

When you are operating on Packet, switch the Receive Battery Saver OFF, as the “sleep”

cycle may “collide” with the beginning of an incoming Packet transmission, causing your

TNC not to receive the full data burst. See page 59 for details regarding Battery Saver

setup.

INTERFACE OF PACKET TNCS

CT-44

EAR

MIC

10µF

2 kO

GND

MIC

PTT

TNC

MIC/SP

OPERATIO N

Hi! I’m R. F. Radio, and I’ll be helping you along as you learn the many

features of the FT-60R. I know you’re anxious to get on the air, but I encourage

you to read the “Operation” section of this manual as thoroughly as

possible, so you’ll get the most out of this fantastic new transceiver. Now. . .let’s get

operating!

SWITCHING POWER ON

AND OFF

Be sure the Battery Pack is installed, and that the battery

is fully charged. Connect the antenna to the top panel

Antenna jack.

Rotate the top panel’s VOL knob out of the click-stop to

turn on the radio. The current DC supply voltage will be

indicated on the display for 2 seconds. After this 2 second

interval, the display will resume its normal indication

of the operating frequency.

To turn the radio off, turn the VOL knob fully counter-clockwise into the click stop

position.

ADJUSTING

THE AUDIO VOLUME LEVEL

AND SQUELCH SETTING

At first, set the SQL knob fully counter-clockwise. Now,

you may rotate the VOL knob to adjust the receiver level

for a comfortable listing level, using the background

noise as a reference.

To set the squelch, turn the SQL knob clockwise, slightly

past the point where the background noise is muted. This

is the point of best sensitivity to weak signals, and we

recommend that you not rotate the SQL knob very much past the point where the

background noise is just silenced.

1) A special “RF Squelch” feature is provided on this radio. This feature

allows you to set the squelch so that only signals exceeding a certain S-meter

level will open the squelch. See page 18 for details.

2) If you’re operating in an area of high RF pollution, you may need to consider “Tone

Squelch” operation using the built-in CTCSS Decoder. This feature will keep your radio

quiet until a call is received from a station sending a carrier which contains a matching

(subaudible) CTCSS tone. Or, if your friends have radios equipped with DCS (Digital

Coded Squelch) like your FT-60R has, try using that mode for silent monitoring of busy

channels.

FT-60R OPERATING MANUAL

FT-60R OPERATING MANUAL 13

OPERATION

SELECTING THE OPERATING BAND

. Press the [BAND(BAND DN)] key repetitively. You will

see the LCD indication move toward a higher frequency

band each time you press the [BAND(BAND DN)] key.

850 MHz . 144 MHz .

250 MHz . 350 MHz .

430 MHz . 850 MHz ……

. If you wish to move the operating band selection downward

(toward a lower frequency band), press the [F/W]

key first, then press the [BAND(BAND DN)] key.

350 MHz . 250 MHz .

144 MHz . 850 MHz .

430 MHz . 350 MHz ……

. Once you have selected the desired band, you

may initiate manual tuning (or scanning) per

the discussion in the next chapter.

FREQUENCY NAVIGATION

The FT-60R will initially be operating in the “VFO” mode, a channelized system which

allows free tuning throughout the currently-selected operating band.

Three basic frequency navigation methods are available on the FT-60R:

1) Tuning Dial

Rotation of the DIAL allows tuning in the pre-programmed

steps established for the current operating band. Clockwise

rotation of the DIAL causes the FT-60R to be tuned toward

a higher frequency, while counter-clockwise rotation will

lower the operating frequency.

If you press the [F/W] key momentarily, then rotate the DIAL,

frequency steps of 1 MHz will be selected. This feature is

extremely useful for making rapid frequency excursions over the wide tuning range of the

FT-60R.

FREQUENCY RANGE

108.000 - 200.000 MHz

200.000 - 300.000 MHz

300.000 - 400.000 MHz

400.000 - 520.000 MHz

700.000 - 999.990 MHz

BAND

144 MHz Band

250 MHz Band

350 MHz Band

430 MHz Band

850 MHz Band

OPERATIO N

FREQUENCY NAVIGATION

2) Direct Keypad Frequency Entry

The desired operating frequency may be entered directly from the keypad.

To enter a frequency from the keypad, just press the numbered digits on the keypad in the

proper sequence.

Examples:

To enter 146.560 MHz, press [1] .

[4] .

[6] .

[5] .

[6] .

[0]

To enter 146.5625 MHz (in 12.5 kHz), [1] .

[4] .

[6] .

[5] .

[6] .

[2]

3) Scanning

Press and hold in either the [.(MHz)] or [.(MHz)] key

for one second to initiate upward or downward scanning,

respectively (Manual VFO Scan).

For scanning within a limited sub-band range, from the VFO

mode, press and hold in the [V/M(PRI)] key for one second

to begin scanning toward a higher frequency within the previously-

defined sub-band (Programmed VFO Scan). Details

(Manual VFO Scan)

(Programmed VFO Scan)

regarding sub-band setup may be found on page 36.

If you wish to reverse the direction of the scan (i.e. toward a

lower frequency, instead of a higher frequency), just rotate

the DIAL one click in the counter-clockwise direction while

the FT-60R is scanning. The scanning direction will be reversed.

To revert to scanning toward a higher frequency once

more, rotate the DIAL one click clockwise.

The scanner will stop when it receives a signal strong enough to break through the Squelch

threshold. The FT-60R will then hold on that frequency according to the setting of the

“RESUME” mode (Set Mode Item 34: RESUME). Press the PTT switch momentarily to

cancel the scanning. This only stops the scan; it does not cause transmission to occur. See

page 35 for details regarding Scan Operation.

FT-60R OPERATING MANUAL

OPERATION

TRANSMISSION

Once you have set up an appropriate frequency inside one of the 144 MHz or 430 MHz

Amateur bands on which the FT-60R can transmit, you’re ready to go on the air! These are

the most basic steps; more advanced aspects of transmitter operation will be discussed later.

To transmit, press the PTT switch, and speak into the

front panel microphone (located in the lower left-hand

corner of the speaker grille) in a normal voice level. The

TX/BUSY indicator will glow red during transmission.

To return to the receive mode, release the PTT switch.

During transmission, the relative power level will be

indicated on the bar graph at the bottom of the LCD;

full scale deflection confirms “High Power” operation, while deflection of two bars

indicates “Low Power” operation. Five bars indicates “Medium Power” operation.

Additionally, the “LOW” icon will appear at the bottom of the display while operating

on the “Low Power” and “Medium Power” settings.

1) If you’re just talking to friends in the immediate area, you’ll get much longer

battery life by switching to Low Power operation, described in the next chapter.

And don’t forget: always have an antenna connected when you transmit.

2) Transmission is possible only on the 144 MHz and 430 MHz bands.

Changing the Transmitter Power Level

To change the power level:

Press the [F/W] key, then press the [3(TX PO)] key.

The LCD shows the current power output level.

Rotate the DIAL knob to select the desired power output

level. Available selections are “HIGH” (5 W), “MID”

(2 W), and “LOW” (0.5 W).

When you have made your choice, press the PTT switch

to save the new setting and return to normal operation.

1) The FT-60R is smart! You can set up Low power on the 144 MHz band,

while leaving 430 MHz on High power, and the radio will remember the

different settings on both bands. And when you store memories, you can store

the power output settings separately in each memory, so you don’t waste battery power

when using very close-in repeaters!

2) When you are operating on the “Low” or “Medium” power setting, you can press the

[F/W] key, when press the PTT switch, to cause the FT-60R to transmit (temporarily) on

High power. After one transmission, the power level will revert to the previously-selected

(“Low” or “Medium” power) setting.

FT-60R OPERATING MANUAL

ADVANCED OPERATION

Now that you’re mastered the basics of FT-60R operation, let’s learn more about some of

the really neat features.

KEYBOARD LOCKING

In order to prevent accidental frequency change or inadvertent transmission, various aspects

of the FT-60R’s DIAL and keypad may be locked out. The possible lockout combinations

are:

LK KEY: Just the front panel keypad is locked out

LKDIAL: Just the top panel DIAL is locked out

LK K+D: Both the keypad and DIAL are locked out (factory default)

LK PTT: The PTT switch is locked out (TX not possible)

LK P+K: Both the PTT switch and keypad are locked out

LK P+D: Both the PTT switch and DIAL are locked out

LK ALL: All of the above are locked out

To lock out some or all of the keys:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 25: LOCK.

Press the [F/W] key momentarily to enable adjustment of this

Item.

Rotate the DIAL knob to choose between one of the locking

schemes as outlined above.

When you have made your selection, press the PTT switch to

save the new setting and return to normal operation.

the LCD. To cancel locking, repeat this process.

To activate the locking feature, (1) press and hold in the

[6(LOCK)] key for one second, or (2) press the [F/W] key,

then press the [6(LOCK)] key. The “ ” icon will appear on

FT-60R OPERATING MANUAL

ADVANCED OPERATION

KEYPAD/LCD ILLUMINATION

Your FT-60R includes a reddish illumination lamp which aids in nighttime operation. The

reddish illumination yields clear viewing of the display in a dark environment, with minimal

degradation of your night vision.

Three options for activating the lamp are provided:

KEY Mode: Illuminates the Keypad/LCD lamp for five seconds when you rotate

the DIAL knob or press the keypad or any switch (except PTT switch).

This is the factory-programmed default setting.

5SEC Mode: Illuminates the Keypad/LCD lamp for five seconds when you press

the LAMP switch momentarily.

TOGGLE Mode: Toggles the Keypad/LCD lamp on and off when you press the LAMP

switch momentarily.

Here is the procedure for setting up the Lamp operating mode:

Press the [F/W] key, then press the [0()SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 24: LAMP.

Press the [F/W] key momentarily to enable adjustment of this

Item.

Rotate the DIAL knob to select one of the three modes described

above.

When you have made your choice, press the PTT switch to save

the new setting and return to normal operation.

Press the [F/W] key first, then press the LAMP switch to illuminate the Key-

pad/LCD lamp continuously until you press the LAMP key again, irrespective

of the Lamp mode programmed per the above instructions.

DISABLING

THE KEYPAD BEEPER

A keypad beeper provides useful audible feed back whenever a keypad is pressed.

If you want to turn the beep off:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 6: BEEP.

Press the [F/W] key momentarily to enable adjustment of this

Item.

Rotate the DIAL knob to change the setting to “OFF.”

5. Press the PTT switch to save the new setting and return to normal

operation.

To turn the beep back on again, select “KEY” or “KEY+SC (factory default)” in step 4

above.

KEY: The beeper sounds when you press the keypad.

KEY+SC: The beeper sounds when you press the keypad, or when the scanner stops.

FT-60R OPERATING MANUAL

ADVANCED OPERATION

RF SQUELCH

A special RF Squelch feature is provided on this radio. This feature allows you to set the

squelch so that only signals exceeding a certain S-meter level will open the squelch.

To set up the RF squelch circuit for operation, use the following procedure:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 37: RF SQL.

3. Press the [F/W] key momentarily to enable adjustment of this

Item.

4. Rotate the DIAL knob to select the desired signal strength level

for the squelch threshold (S-1, S-2, S-3, S-4, S-5, S-6, S-8, S

FULL, or OFF).

Press the PTT switch to save the new setting and return to normal operation.

Finally, rotate the SQL knob fully clockwise.

CHECKING

THE BATTERY VOLTAGE

The FT-60R’s microprocessor includes programming which will measure the current battery

voltage.

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 12: DC VLT.

Press the [F/W] key momentarily to display the current DC voltage

being supplied.

4. Press the PTT switch to return to normal operation.

FT-60R OPERATING MANUAL

REPEATER OPERATION

Repeater stations, usually located on mountaintops or other high locations, provide a dramatic

extension of the communication range for low-powered hand-held or mobile transceivers.

The FT-60R includes a number of features which make repeater operation simple

and enjoyable.

REPEATER SHIFTS

Your FT-60R has been configured, at the factory, for the repeater shifts customary in your

country. For the 144 MHz band shift will be 600 kHz; on the 430 MHz band, the shift may

be 1.6 MHz, 7.6 MHz, or 5 MHz (USA version).

Depending on the part of the band in which you are operating, the repeater shift may be

either downward ( ) or upward ( ), and one

of these icons will appear at the top of the LCD

when repeater shifts have been enabled.

AUTOMATIC REPEATER SHIFT

(ARS)

The FT-60R provides a convenient Automatic Repeater Shift feature, which causes the

appropriate repeater shift to be applied automatically whenever you tune into the designated

repeater sub-bands in your country. These sub-bands are shown below.

If the ARS feature does not appear to be working, you may have accidentally disabled it.

To re-enable ARS:

1. Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 4: ARS.

3. Press the [F/W] key momentarily to enable adjustment of this

Item.

4. Rotate the DIAL knob to select “ARS. ON.”

5. When you have made your selection, press the PTT switch to

save the new setting and return to normal operation.

FT-60R OPERATING MANUAL

REPEATER OPERATION

MANUAL REPEATER SHIFT ACTIVATION

If the ARS feature has been disabled, or if you need to set a repeater shift direction other

than that established by the ARS, you may set the direction of the repeater shift manually.

To do this:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 38: RPT.MOD.

Press the [F/W] key momentarily to enable adjustment of this

Item.

Rotate the DIAL knob to select the desired shift among “RPT.–,”

“RPT.+,” and “RPT.OFF.”

When you have made your selection, press the PTT switch to

save the new setting and return to normal operation.

If you make a change in the shift direction, but still have Automatic Repeater

Shift still engaged (see previous section), when you change frequency (by

rotating the DIAL knob, for example) the ARS will over-ride your manual

setting of the shift direction. Turn ARS off if you do not wish this to happen.

Changing the Default Repeater Shifts

If you travel to a different region, you may need to change the default repeater shift so as to

ensure compatibility with local operating requirements.

To do this, follow the procedure below:

Set the FT-60R’s frequency to the band on which you wish to change the default

repeater shift (144 MHz or 430 MHz Amateur Band).

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

3. Rotate the DIAL knob to select Set Mode Item 45: SHIFT.

4. Press the [F/W] key momentarily to enable adjustment of this

Item.

5. Rotate the DIAL knob to select the new repeater shift magnitude.

When you have made your selection, press the PTT switch to

save the new setting and return to normal operation.

If you just have one “odd” split that you need to program, don’t change the

“default” repeated shifts using this Set Mode Item. Enter the transmit and

receive frequencies separately, as shown on page 28.

FT-60R OPERATING MANUAL

REPEATER OPERATION

MANUAL REPEATER SHIFT ACTIVATION

Checking the Repeater Uplink (Input) Frequency

It often is helpful to be able to check the uplink (input) frequency of a repeater, to see if the

calling station is within direct (“Simplex”) range.

To do this, just press the [HM/RV] key. You’ll notice that

the display has shifted to the repeater uplink frequency. Press

the [HM/RV] key again to cause operation to revert to normal

monitoring of the repeater downlink (output) frequency.

While you are listening on the input frequency to the repeater

using the [HM/RV] key, the repeater offset icon will

blink.

The configuration of this key may be set either to “RV” (for checking the

input frequency of a repeater), or “HM” (for instant switching to the “Home”

channel for the band you are operating on). To change the configuration of

this key, use Set Mode Item 36: REV/HM. See page 75.

FT-60R OPERATING MANUAL

CTCSS/DCS OPERATION

CTCSS OPERATION

Many repeater systems require that a very-low-frequency audio tone be superimposed on

your FM carrier in order to activate the repeater. This helps prevent false activation of the

repeater by radar or spurious signals from other transmitters. This tone system, called

“CTCSS” (Continuous Tone Coded Squelch System), is included in your FT-60R, and is

very easy to activate.

CTCSS setup involves two actions: setting the Tone Mode and then setting of

the Tone Frequency. These actions are set up by using the [1(SQ TYP)] key

and [2(CODE)] key.

1. Press the [F/W] key, then press the [1(SQ TYP)] key to enable selection of the CTCSS/

DCS mode.

Rotate the DIAL knob so that “TONE” indication appears on the

display; this activates the CTCSS Encoder, for access to repeaters

requiring a CTCSS tone.

Rotation of the DIAL knob one more “click” in step “2” above will cause the “TSQL”

notation to appear. When “TSQL” is displayed, this means that the Tone SQueLch

system is active, which mutes your FT-60R’s receiver until it receives a call from

another radio sending out a matching CTCSS tone. This can

help keep your radio quiet until a specific call is received, which

may be helpful while operating in congested areas of the band.

1) You may notice a “REV TN” indication on the display while you rotate

the DIAL knob in this step; this means that the Reverse Tone Squelch

system is active, which mutes your FT-60R’s receiver (instead of opening

the squelch) when it receives a call from the radio sending a matched CTCSS tone.

The “TSQ” icon will blink on the display when the Reverse Tone Squelch system is

activated.

2) You may notice a “DCS” indication on the display while you rotate the DIAL

knob still more. We’ll discuss the Digital Code Squelch system shortly.

When you have made your selection of the CTCSS tone mode, press the PTT switch

to save the new setting.

Press the [F/W] key, then press the

[2(CODE)] key to enable adjustment of

the CTCSS frequency.

Rotate the DIAL knob until the display

indicates the Tone Frequency you need to

be using (ask the

CTCSS TONE FREQUENCY (Hz)

67.0 69.3 71.9 74.4 77.0 79.7

82.5 85.4 88.5 91.5 94.8 97.4

100.0 103.5 107.2 110.9 114.8 118.8

123.0 127.3 131.8 136.5 141.3 146.2

151.4 156.7 159.8 162.2 165.5 167.9

171.3 173.8 177.3 179.9 183.5 186.2

189.9 192.8 196.6 199.5 203.5 206.5

210.7 218.1 225.7 229.1 233.6 241.8

250.3 254.1 – – – –

repeater owner/

operator if you

don’t know the tone frequency).

FT-60R OPERATING MANUAL

CTCSS/DCS OPERATION

CTCSS OPERATION

7. When you have made your selection, press the [F/W] key momentarily to save the new

settings and exit to normal operation. This is different than the

usual method of restoring normal operation, and it applies only

to the configuration of the CTCSS/DCS frequencies.

Your repeater may or may not re-transmit a CTCSS tone - some systems just

use CTCSS to control access to the repeater, but don’t pass it along when

transmitting. If the S-Meter deflects, but the FT-60R is not passing audio,

repeat steps “1” through “4” above, but rotate the DIAL so that “TSQ” disappears - this

will allow you to hear all traffic on the channel being utilized.

DCS OPERATION

Another form of tone access control is Digital Code Squelch, or DCS. It is a newer, more

advanced tone system which generally provides more immunity from false paging than

does CTCSS. The DCS Encoder/Decoder is built into your FT-60R, and operation is very

similar to that just described for CTCSS. Your repeater system may be configured for

DCS; if not, DCS is frequently quite useful in Simplex operation if your friend(s) use

transceivers equipped with this advanced feature.

Just as in CTCSS operation, DCS requires that you set the Tone Mode to DCS and that

you select a tone code.

Press the [F/W] key, then press the [1(SQ TYP)] key to enable selection of the CTCSS/

DCS mode.

2. Rotate the DIAL knob until the “DCS” indication appears on the

display; this activates the DCS Encoder/Decoder.

Press the PTT key to save the new setting.

Press the [F/W] key, then press the [2(CODE)] key to enable

adjustment of the DCS code.

5. Rotate the DIAL knob to select the desired DCS Code (a three-

digit number). Ask the repeater owner/operator

if you don’t know DCS Code; if

you are working simplex, just set up the

DCS Code to be the same as that used by

your friend(s).

When you have made your selection, press

the [F/W] key momentarily to save the

DCS CODE

023 025 026 031 032 036 043 047 051 053

054 065 071 072 073 074 114 115 116 122

125 131 132 134 143 145 152 155 156 162

165 172 174 205 212 223 225 226 243 244

245 246 251 252 255 261 263 265 266 271

274 306 311 315 325 331 332 343 346 351

356 364 365 371 411 412 413 423 431 432

445 446 452 454 455 462 464 465 466 503

506 516 523 526 532 546 565 606 612 624

627 631 632 654 662 664 703 712 723 731

732 734 743 754 – – – – – –

new settings and

exit to normal op

eration.

FT-60R OPERATING MANUAL

CTCSS/DCS OPERATION

DCS OPERATION

Remember that the DCS is an Encode/Decode system, so your receiver will

remain muted until a matching DCS code is received on an incoming transmission.

Switch the DCS off when you’re just tuning around the band!

TONE SEARCH SCANNING

In operating situations where you don’t know the CTCSS or DCS tone being used by

another station or stations, you can command the radio to listen to the incoming signal and

scan in search of the tone being used. Two things must be remembered in this regard:

You must be sure that your repeater uses the same tone type (CTCSS vs. DCS).

Some repeaters do not pass the CTCSS tone; you may have to listen to the station(s)

transmitting on the repeater uplink (input) frequency in order to allow Tone Search

Scanning to work.

To scan for the tone in use:

Set the radio up for either CTCSS or DCS Decoder operation (see the previous discussions).

In the case of CTCSS, “

” will appear on the display; in the case of DCS,

” will appear on the display.

Press the [F/W] key, then press the [2(CODE)] key.

Press and hold in the [.(MHz)] or [.(MHz)] key for one second

to start scanning for the incoming CTCSS or DCS tone/

“

code.

When the radio detects the correct tone or code, it will halt on

that tone/code, and audio will be allowed to pass. Press the

[F/W] key to lock in that tone/code, then press the [F/W] key again to exit to normal

operation.

If the Tone Scan feature does not detect a tone or code, it will continue to

scan indefinitely. When this happens, it may be that the other station is not

sending any tone. You can press the PTT switch to halt the scan at any time.

You also can press the MONI key during Tone Scanning to listen to the (muted) signal

from the other station. When you release the MONI key, Tone Scanning will resume after

about a second.

Tone Scanning works either in the VFO or Memory modes.

FT-60R OPERATING MANUAL

CTCSS/DCS OPERATION

CTCSS/DCS BELL OPERATION

During CTCSS Decode or DCS operation, you may set up the FT-60R such that a ringing

“bell” sound alerts you to the fact that a call is coming in. Here is the procedure for activating

the CTCSS/DCS Bell:

Set the transceiver up for CTCSS Decode (“Tone Squelch”) or DCS operation, as

described previously.

Adjust the operating frequency to the desired channel.

Press the [F/W] key, then press the [5(BELL)] key.

4. Rotate the DIAL knob to set the desired number of rings of the

Bell. The available choices are “1 T,” “3 T,” “5 T,” or “8 T”

rings, “CONT” (continuous ringing), or “OFF.”

Press the PTT switch momentarily to save the new setting and exit to normal operation.

When you are called by a station whose transceiver is sending a

CTCSS tone or DCS code which matches that set into your Decoder,

the Bell will ring in accordance with this programming.

SPLIT TONE OPERATION

The FT-60R can be operated in a Split Tone configuration via the Set mode.

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 47: SPLIT.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to select ON (to enable the Split Tone

feature).

Press the PTT key momentarily to save the new setting and exit

to normal operation.

When the Split Tone feature is activated, you can see the following additional parameters

following the “DCS” parameter (while selecting the tone mode by pressing [F/W] .

[1(SQ TYP)]):

D: DCS Encode only (the “

” icon will blink during operation)

T DCS: Encodes a CTCSS Tone and Decodes a DCS code

(the “

” icon will blink and the “

” icon will appear during operation)

D TSQL: Encodes a DCS code and Decodes a CTCSS Tone

(the “

” icon will appear and the “

” icon will blink during operation)

Select the desired operating mode, from the selections shown above.

FT-60R OPERATING MANUAL

CTCSS/DCS OPERATION

TONE CALLING

(1750 HZ)

If the repeaters in your country require a 1750-Hz burst tone for access (typically in Europe),

you can set the MONI key to serve as a “Tone Call” switch instead. To change the

configuration of this switch, we again use the Set Mode to help us.

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 26: M/T-CL.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to select “TCALL” on the display.

Press the PTT switch to save the new setting and exit to normal

operation.

To access a repeater, press and hold in the MONI key for the amount of time specified by

the repeater owner/operator. The transmitter will automatically be activated, and a 1750Hz

audio tone will be superimposed on the carrier. Once access to the repeater has been

gained, you may release the MONI key, and use the PTT key for activating the transmitter

thereafter.

FT-60R OPERATING MANUAL

FT-60R OPERATING MANUAL 27

The FT-60R provides a wide variety of memory system resources. These include:

. 1000 “Standard” memory channels, numbered “000” through “999.”

. 5 “Home” channels, providing storage and quick recall of one prime frequency on

each operating band.

. 50 sets of band-edge memories, also known as “Programmable Memory Scan” channels,

labeled “L01/U01” through “L50/U50.”

. 10 Memory Banks, labeled “BANK 1” through “BANK10.” Each Memory Bank can

be assigned up to 1000 channels from the “standard” and “PMS” memory channels.

. 10 “Weather Broadcast” Channels.

MEMORY MODE

L50/U50

000

850 MHz Band

430 MHz Band

350 MHz Band

250 MHz Band

144 MHz Band

HOME Channels

(5 channels)

999

998

Memory Bank 10

Memory Bank 9

Memory Bank 8

Memory Bank 7

Memory Bank 6

Memory Bank 5

Memory Bank 4

Memory Bank 3

Memory Bank 2

Memory Bank 1

L49/U49

L48/U48

L4/U4

L3/U3

L2/U2

L1/U1

Standard Memory Channels

(1000 channels)

PMS Memory Channels

(50 Sets)

Weather Broadcast Channels

(10 channels)

WX10

WX9

WX4

WX3

WX2

WX1

Memory Banks

(10 banks)

MEMORY MOD E

MEMORY STORAGE

Select the desired frequency, while operating in the VFO mode. Be sure to set up any

desired CTCSS or DCS tones, as well as any desired repeater offset. The power level

may also be set at this time, if you wish to store it.

Press and hold in the [F/W] key for one second.

Within five seconds of releasing the [F/W] key, you need to make a decision regarding

channel storage. The microprocessor will automatically select the next-available “free”

channel (a memory register on which no data has been stored), so you may not wish to

make any change; if this is the case, proceed to step 4. If you wish to select a different

channel number into which to store the data, rotate the DIAL knob to select the desired

memory channel. You may jump 100 memory channels, if you’re in a hurry (101 .

201 .

301 …) by pressing the [BAND(BAND DN)] key (multiple times, if necessary).

Press the [F/W] key once more to store the frequency into memory.

You still will be operating in the “VFO” mode, so you may now enter other frequencies,

and store them into additional memory locations, by repeating the above process.

Storing Independent Transmit Frequencies (“Odd Splits”)

All memories can store an independent transmit frequency, for operation on repeaters with

non-standard shift. To do this:

Store the receive frequency using the method already described under MEMORY

STORAGE (it doesn’t matter if a repeater offset is active).

Turn to the desired transmit frequency, then press and hold in the [F/W] key for one

second.

Within five seconds of releasing the [F/W] key, rotate the DIAL knob to select the

same memory channel number as used in step “1” above.

Press and hold in the PTT switch, then press the [F/W] key once more momentarily

while holding the PTT switch in (this does not key the transmitter).

Whenever you recall a memory which contains inde

pendently-stored transmit and receive frequencies, the

“

” indication will appear in the display.

FT-60R OPERATING MANUAL

MEMORY MODE

MEMORY RECALL

1. While operating in the VFO mode, press the [V/M(PRI)] key to enter the Memory

mode.

Rotate the DIAL knob to select the desired channel.

To return to the VFO mode, press the [V/M(PRI)] key.

When the radio is already set to the Memory mode, an easy way to recall memories is to

key in the memory channel number, then press the [F/W] key.

For example, to recall memory channel #14, press [1] .

[4] .

[F/W].

You may also recall the Memory Channel #000 and Programmable Memory channels (“L01/

U01” through “L50/U50.”) using the following numbers: Memory Channel #000 = “1000,”

Programmable Memory channels #L1 = “1001,” U1 = “1002,” L50 = “1099,” and U50 =

“1100.”

HOME CHANNEL MEMORY

A special one-touch “HOME” channel is available for each of operating bands, to allow

quick recall of a favorite operating frequency on each band.

Home Channel storage is simple to accomplish:

Change the setting of Set Mode Item 35: REV/HM from “REV” to “HOME,” if it is not

already set to this option (see page 75).

Select the desired frequency, while operating in the VFO mode. Be sure to set up any

desired CTCSS or DCS tones, as well as any desired repeater offset. The power level

may also be set at this time, if you wish to store it.

Press and hold in the [F/W] key for one second.

While the memory channel number is blinking, just press the [HM/RV] key. The frequency

and other data (if any) will now be stored in the special HOME channel register.

DEFAULT HOME CHANNELS

You may repeat this process on the other operating bands.

To recall the HOME channel,

press the [HM/RV] key momentarily

while operating either in the

BAND

FREQUENCY

144 MHz Band 146.520 MHz

250 MHz Band 250.000 MHz

350 MHz Band 350.000 MHz

430 MHz Band 446.000 MHz

850 MHz Band 850.000 MHz

VFO or MR mode.

The UHF HOME channel is the one used during “Emergency channel operation.”

See page 46 for details regarding this feature.

FT-60R OPERATING MANUAL

MEMORY MODE

LABELING MEMORIES

You may wish to append an alpha-numeric “Tag” (label) to a memory or memories, to aid

in recollection of the channel’s use (such as a club name, etc.). This is easily accomplished

using the Set Mode.

Recall the memory channel on which you wish to append a label.

Press the [F/W] key, then press the [0(

)SET] key to enter the

Set mode.

Rotate the DIAL knob to select Set Mode Item 28: NM WRT.

Press the [F/W] key momentarily to display the previously stored

label (if any).

Press the [F/W] key again to clear any previous label.

Rotate the DIAL knob to select the first digit of the desired label.

Press the [F/W] key to move to the next character.

If you make a mistake, press the [.(MHz)] key to back-space the cursor, then re-enter

the correct letter, number, or symbol.

Repeat steps 5 through 7 to program the remaining letters, numbers, or symbols of the

desired label. A total of six characters may be used in the creation of a label.

10.

When you have programmed a label which is under 6 characters, press and hold in the

[F/W] key for one second to confirm the label (if the label is

exactly 6 characters in length, you do not need to press and hold

in [F/W]).

11.

When you have completed the creation of the label, press the PTT key to save the

label and exit.

To display the alpha-numeric “Tag” (label):

1. Set the FT-60R to the “MR” (Memory Recall) mode, and recall

the memory channel on which you wish to display its label.

Press the [F/W] key, then press the [0(

)SET] key to enter the

Set mode.

3. Rotate the DIAL knob to select the Set Mode Item labeled 27:

NAME.

Press the [F/W] key momentarily to enable adjustment of this

Item’s setting.

Rotate the DIAL knob to set this Set Mode Item to “ALPHA”

(thus enabling the alpha-numeric display).

Press the PTT key to save the new setting and activate the alpha-

numeric Tag.

FT-60R OPERATING MANUAL

MEMORY MODE

LABELING MEMORIES

To disable the alpha-numeric Tag (enabling the frequency display), just repeat the above

procedure, rotating the DIAL knob to select “FREQ” in step 5 above.

You may set up some memory channels to have their frequencies displayed,

while others may be set to have their Name Tag displayed; the selection within

Set Mode Item 27 is not applied to all memory channels at once (just the

channel on which you currently are operating).

MEMORY OFFSET TUNING

Once you have recalled a particular memory channel, you may easily tune off that channel,

as though you were in the “VFO” mode.

1. With the FT-60R in the “MR” (Memory Recall) mode, select

the desired memory channel.

Press the [BAND(BAND DN)] key momentarily to activate the

“Memory Tuning” feature. The Memory Channel number will

be replaced by “tun.” And if you have an alpha-numeric Tag

displayed on the memory channel, the display will automatically

revert to display of the operating frequency, so you can

navigate without having to enter the Menu to change the display

configuration.

Rotate the DIAL knob, as desired, to tune to a new frequency.

The synthesizer steps selected for VFO operation on the current

band will be the steps used during Memory Tuning.

If you wish to return to the original memory frequency, just press the [BAND(BAND

DN)] key momentarily. The display will revert to display of the alpha-numeric Tag (if

any) that may have originally appeared on the LCD.

If you wish to store a new frequency set during Memory Tuning, just press and hold in

the [F/W] key for one second, per normal memory storage procedure. The microprocessor

will automatically set itself to the next-available clear memory location, and

you then press [F/W] again to lock in the new frequency.

1) If you want to replace the original memory contents with those of the new

frequency, be sure to rotate the DIAL knob to the original memory channel

number!

2) Any required CTCSS/DCS changes, or repeater offset modifications, must be done

before storing the data into the new (or original) memory channel location.

FT-60R OPERATING MANUAL

MEMORY MODE

DELETING MEMORIES

You may desire to delete the memories (except the Memory Channel “1” and Home Channel).

The procedure for deleting a channel is quite simple.

Press the [V/M(PRI)] key, if needed, to enter the MR mode.

Press and hold in the [F/W] key for one second, then rotate the DIAL knob to select

the memory channel to be “deleted.”

Press the [HM/RV] key momentarily. The display will revert to memory channel #1.

The previously-selected memory will be deleted.

Important Notice! Once deleted, the channel data cannot be recovered!

MOVING MEMORY DATA

THE VFO

Data stored on memory channels can easily be moved to the VFO, if you like.

Select the memory channel containing the frequency data to be moved to the VFO.

Press the [BAND(BAND DN)] key momentarily to activate the “Memory Tune” feature

temporarily, then press and hold in the [BAND(BAND DN)] key for one second.

The data will now have been copied to the VFO, although the original memory contents

will remain intact on the previously-stored channel.

If a Split Frequency Memory channel was transferred, the TX frequency will

be ignored (you will be set up for Simplex operation on the Receive frequency).

FT-60R OPERATING MANUAL

MEMORY MODE

MEMORY BANK OPERATION

The large number of memories available in the FT-60R could be difficult to utilize without

some means of organizing them. Fortunately, the FT-60R includes provision for dividing

the memories into as many as ten Memory Groups, so you can categorize the memories in

a manner convenient to you. You may enter and exit the “Memory Group” mode by a

single press of the [BAND(BAND DN)] key, as we shall see below.

Assigning Memories to a Memory Bank

1. Recall the memory channel to be assigned to a Memory Bank.

2. Press and hold in the [BAND(BAND DN)] key for one second,

then rotate the DIAL knob to select the Memory Bank number

you want as the Memory Bank for this channel (“BANK 1” ~

“BANK10”).

3. Press and hold in the [F/W] key for one second to copy the memory

channel data into the Memory Bank.

Memory Channel

CH 000 145.000 MHz

CH 001 145.500 MHz

CH 002 435.000 MHz

CH 003 435.500 MHz

CH 004 145.800 MHz

You may assign one

memory channel into several

CH 005 436.000 MHz

CH 006 128.800 MHz

Memory Banks.

2) The PMS memory channels (L1/U1

through L50/U50) may not be assigned

CH 997 145.620 MHz

CH 998 436.780 MHz

CH 999 128.600 MHz

to a Memory Bank.

Memory Bank Recall

Press the [V/M(PRI)] key, if needed, to enter the Memory mode.

Press and hold in the [BAND(BAND DN)] key, then rotate the

Memory Bank “5”

Air Band Channels

Memory Bank “4”

Club Channels

Memory Bank “3”

All Amateur Band Channels

Memory Bank “1”

144 MHz Amateur Band Channels

Memory Bank “2”

430 MHz Amateur Band Channels

DIAL knob to select the desired Memory Bank (“BANK 1”

through “BANK10”).

Press the [V/M(PRI)] key momentarily; now, as you rotate the

DIAL knob to select memories, you will observe that you can

only select memory channels in the current memory bank. The

“

” indication will appear at the left side of the frequency

display while operating within a Memory Bank.

To change to another Memory Bank, press and hold in the [BAND(BAND DN)] key,

rotate the DIAL knob to select the new Memory Bank, then press the [V/M(PRI)] key

momentarily.

To exit from Memory Bank operation, select “NOBANK” in step 4 above. You are

now in the “standard” Memory Recall mode, without utilization

of the Memory Banks. The memories stored in the various Banks

will remain in those banks, however; you do not need to store

them again.

FT-60R OPERATING MANUAL

MEMORY MODE

MEMORY ONLY MODE

Once memory channel programming has been completed, you may place the radio in a

“Memory Only” mode, whereby VFO operation is impossible. This may be particularly

useful during public-service events, where a number of operators may be using the radio

for first time, and ultimate simplicity of channel selection is desired.

To place the radio into the Memory Only mode:

Turn the radio off.

Press and hold in the MONI switch (just below the PTT switch)

while turning the radio on.

Rotate the DIAL knob to select the “F5 M-ONLY” option, then

press the [F/W] key.

To return to normal operation, repeat the above power-on proce

dure.

WEATHER BROADCAST CHANNELS

(U. S. VERSION)

The VHF Weather Broadcast Station Memory Channel Bank has been pre-programmed at

the factory, for quick selection of NOAA weather information stations.

Press and hold in the [1(SQ TYP)] key for one second to recall

the Weather Broadcast Memory Bank.

Rotate the DIAL knob to select the desired Weather Broadcast

channel.

If you wish to scan this bank to search for louder stations, just press the PTT switch.

When the scanner pauses on a station, press the

PTT key once to halt the scan, or press it twice

to restart the scan.

To exit to normal operation, press the [V/M(PRI)]

key, or press and hold in the [1(SQ TYP)] key

CH FREQUENCY

01 162.550 MHz 06 162.500 MHz

02 165.400 MHz 07 165.525 MHz

03 162.475 MHz 08 161.650 MHz

04 162.425 MHz 09 161.775 MHz

05 162.450 MHz 10 163.275 MHz

again.

Severe Weather Alert

In the event of extreme weather disturbances, such as severe thunderstorms and hurricanes,

the NOAA (National Oceanic and Atmospheric Administration) sends a weather

alert accompanied by a 1050 Hz tone and subsequent weather report on one of the NOAA

weather channels. See page 39 for details regarding activation of this mode.

FT-60R OPERATING MANUAL

SCANNING

The FT-60R allows you to scan just the memory channels, the entire operating band, or a

portion of that band. It will halt on signals encountered, so you can talk to the station(s) on

that frequency, if you like.

Scanning operation is basically the same in each of the above modes. Before you begin,

take a moment to select the way in which you would like the scanner to resume scanning

after it halts on a signal.

Setting the Scan-Resume Technique

Three options for the Scan-Resume mode are available:

BUSY: In this mode, the scanner will halt on a signal it encounters. Two seconds after the

carrier has dropped because the other station(s) ceased transmission, the scanner

will resume. In the case of constant-carrier signals like Weather Station broadcasts,

the scanner will likely remain on this frequency indefinitely.

HOLD: In this mode, the scanner will halt on a signal it encounters. It will not restart

automatically; you must manually re-initiate scanning if you wish to resume.

TIME:

In this mode, the scanner will halt on a signal it encounters, and will hold there for

five seconds. If you do not take action to disable the scanner within that time period,

the scanner will resume even if the stations are still active.

To set the Scan-Resume mode:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 35: RESUME.

3. Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to select the desired scan-resume mode.

When you have made your selection, press the PTT key to save

the new setting and exit to normal operation.

The default condition for this Set Mode Item is “BUSY.”

VFO SCANNING

The FT-60R provides two VFO scanning functions: “Manual VFO Scanning” and “Programmed

VFO Scanning.”

Manual VFO Scan

Select the VFO mode by pressing the [V/M(PRI)] key, if necessary.

Press and hold in either the [.(MHz)] or [.(MHz)] key for one second to initiate

upward or downward scanning, respectively.

If and when the scanner encounters a signal strong enough to open the squelch, the

scanner will halt temporarily; the decimal point of the frequency display will blink

during this “Pause” condition.

FT-60R OPERATING MANUAL

SCANNING

VFO SCANNING

The scanner will then resume according to the Scan-Resume mode selected in the

previous section.

To cancel scanning, press the PTT switch or [V/M(PRI)] key.

Programmed VFO Scan

Select the VFO mode by pressing the [V/M(PRI)] key, if necessary.

Press and hold in the [BAND(BAND DN)] key for one second, then rotate the DIAL

knob to select the bandwidth for the Programmed VFO scanner.

Available selections are ±1 MHz, ±2 MHz, ±5 MHz, ALL, PMSX,

and BAND.

ALL: The scanner will sweep all frequencies.

PMS-X: The scanner will sweep frequencies within the currently-selected PMS frequency

pair. See page 40 for details.

BAND: The scanner will sweep frequencies only on the current band.

Press the [BAND(BAND DN)] key momentarily to save the new setting and exit to

normal operation.

Press and hold in the [V/M(PRI)] key for one second to start scanning.

If and when the scanner encounters a signal strong enough to

open the squelch, the scanner will halt temporarily; the decimal

point of the frequency display will blink during this “Pause”

condition.

The scanner will then resume according to the Scan-Resume mode selected in the

previous section.

To cancel scanning, press the PTT switch or [V/M(PRI)] key.

1) When you start the Programmed VFO Scanner, the FT-60R will be changing

frequency in the upward direction. If you want to change direction of the

scan while it is underway, rotate the DIAL knob one click in the opposite

direction (in this case, one click counter-clockwise). You’ll see the scanner turn around

and change frequency downward!

2) You may change the scanner’s method of operation so that the VFO frequency will

jump to the low band edge of the next band when the VFO frequency reaches the high

edge of the current band (or vice versa). See page 78 regarding Set Mode Item 54: VFO

.BND.

FT-60R OPERATING MANUAL

SCANNING

MEMORY SCANNING

Memory scanning is similarly easy to initiate:

Select the Memory mode by pressing the [V/M(PRI)] key, if necessary.

Press and hold in either the [.(MHz)] or [.(MHz)] key for one second to initiate

upward or downward scanning, respectively.

If and when the scanner encounters a signal strong enough to open the squelch, the

scanner will halt temporarily; the decimal point of the frequency display will blink

during this “Pause” condition.

The scanner will then resume according to the Scan-Resume mode selected in the

previous section.

To cancel scanning, press the PTT switch or [V/M(PRI)] key.

How to Skip (Omit) a Channel during Memory Scan Operation

As mentioned previously, some continuous-carrier stations like a Weather Broadcast station

will seriously impede scanner operation if you are using the “Carrier Drop” Scan-

Resume mode, as the incoming signal will not pause long enough for the transceiver to

resume scanning. Such channels may be “Skipped” during scanning, if you like:

Recall the Memory Channel to be skipped during scanning.

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 46: SKIP.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob so as to select “SKIP.” The current Memory

Channel will now be ignored during scanning. The “ONLY” selection

is used for “Preferential Memory Scan,” described in the

next section.

When you have made your selection, press the PTT key to save the setting and exit to

normal operation.

When you recall the “skipped” memory channel manually, a small

“.” icon will appear at the left of the memory channel number, indicating

it is to be ignored during scanning.

To re-institute a channel into the scanning loop, select “OFF” in step 5 above (the “Skipped”

channel will, of course, still be accessible via manual channel selection methods using the

DIAL knob in the MR mode, whether or not it is locked out of the scanning loop).

In the factory default configuration, you may recall Set Mode Item 46: SKIP

by pressing [F/W] .

[8(P2)].

FT-60R OPERATING MANUAL

SCANNING

MEMORY SCANNING

Preferential Memory Scan

The FT-60R also allows you to set up a “Preferential Scan List” of channels which you can

“flag” within the memory system. These channels are designated by a blinking “.” icon

when you have selected them, one by one, for the Preferential Scan List.

When you initiate memory scanning, beginning on a channel with the blinking “.” icon

appended, only those channels bearing the blinking “.” icon will be scanned. If you initiate

scanning on a channel which does not have the blinking “.” icon appended, you will

scan all channels including those with the blinking “.” icon appended.

Here is the procedure for setting up and using the Preferential Scan List:

Recall the Memory Channel which you wish to add to the Preferential Scan List.

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 46: SKIP.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob so as to select “ONLY.”

When you have made your selection, press the PTT key to save

the settings and exit to normal operation.

To remove a channel from the Preferential Scan List, just repeat the above procedure,

rotating the DIAL knob to select “OFF” in step 5 above.

In the factory default configuration, you may recall Set Mode Item 46: SKIP by pressing

[F/W] .

[8(P2)].

To initiate Preferential Memory Scan:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 43: SCN MD.

Set Mode Item.

Rotate the DIAL knob so as to select “ONLY.”

Press the PTT key to save the settings and exit to normal operation.

Now, press and hold in either the [.(MHz)] or [.(MHz)] key for one second to

initiate the Preferential Memory Scan. Only the channels which have the blinking “.”

icon appended to the channel number will be scanned.

To cancel the Preferential Memory Scan, just repeat the above procedure, rotating the

DIAL knob to select “MEM” in step 4 above

3. Press the [F/W] key momentarily to enable adjustment of this

FT-60R OPERATING MANUAL

SCANNING

MEMORY SCANNING

Memory Bank Scan

When the Memory Bank feature is engaged, the scanner sweeps only memory channels in

the current Memory Bank. However, if the Memory Bank Link Scan feature is enabled,

you may sweep the memory channels in several Memory Banks which you have selected.

To enable the Memory Bank Link Scan feature:

Set the radio to the Memory mode by pressing the [V/M(PRI)] key, if necessary.

Press and hold in the [BAND(BAND DN)] key for one second, then rotate the DIAL

knob to select the first Memory Bank (“BANK 1” ~ “BANK10”) you wish to sweep

using Memory Bank Link Scan.

Press the [F/W] key momentarily. The current Memory Bank will now be swept during

Memory Bank Scan. A “decimal point” will be appended

between the “N” and “K” of the Memory Bank number indication

(such as BAN.K 2).

Repeat steps 2 and 3 above, to append the “decimal point” to any other Memory Banks

you wish to sweep.

Now, press and hold in the [V/M(PRI)] key for one second to

initiate the Memory Bank Link Scan.

To remove a Memory Bank from the Memory Bank Link Scan, repeat steps 2 and 3

above, to delete the “decimal point” from the Memory Bank number indication.

WEATHER ALERT SCAN

This feature allows you to check the Weather Broadcast Memory Channels for the presence

of the NOAA Alert Tone while operating using VFO scan or Memory channel scan.

When the Weather Alert Scan feature is engaged, the FT-60R will check the Weather

Broadcast Memory Channels for activity every five seconds while scanning. If you watch

the display carefully, you'll observe the scanner periodically shifting to the Weather Broadcast

bank, scanning the Weather channels quickly in search of the Alert Tone, after which

regular scanning will resume for another five seconds.

To enable the Weather Alert Scan feature:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 56: WX ALT.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob so as to select “ALT. ON.”

When you have made your selection, press the PTT key to save

the setting and exit to normal operation.

To disable the Weather Alert Scan feature, select “ALT.OFF” in step 4 above.

FT-60R OPERATING MANUAL

SCANNING

WEATHER ALERT SCAN

1) When the Weather Alert Scan feature is engaged, the Scan-Resume mode

is fixed to “TIME.”

2) If you are just scanning the Weather Broadcast Channels, the FT-60R's

receiver will remain muted indefinitely unless the Alert Tone is received. This yields a

long period of monitoring time, as no power will be consumed via audio output while

scanning for the Alert Tone is in progress.

PROGRAMMABLE

(BAND LIMIT) MEMORY SCAN

(PMS)

This feature allows you to set sub-band limits for either scanning or manual VFO operation.

For example, you might wish to set up a limit (in North America) of 144.300 MHz to

148.000 MHz so as to prevent encroachment into the SSB/CW “Weak Signal” portion of

the band below 144.300 MHz. Here’s how to do this:

Set the radio to the VFO mode by pressing the [V/M(PRI)] key, if necessary.

Using the techniques learned earlier, store (per the above concept) 144.300 MHz into

Memory Channel #L01 (the “L” designates the Lower sub-band limit).

Likewise, store 148.000 MHz into Memory Channel #U01 (the “U” designates the

Upper sub-band limit).

Confirm the radio is in the VFO mode, press and hold in the [BAND(BAND DN)] key

for one second, and rotate the DIAL knob to select the desired

PMS frequency pair (PMSxx), then press the [BAND(BAND

DN)] key.

Now, press and hold in the [V/M(PRI)] key for one second to initiate the Programmable

(Band Limit) Memory Scan; the Memory Channel number will be replaced by

“Pxx.” Scanning and tuning will now be limited within the just-programmed range.

50 pairs of Band Limit memories, labeled L01/U01 through L50/U50 are available.

You therefore can set upper and lower operation limits in multiple segments on a

number of bands, if you like.

FT-60R OPERATING MANUAL

SCANNING

“PRIORITY CHANNEL” SCANNING

(DUAL WATCH)

The FT-60R’s scanning features include a two-channel scanning capability which allows

you to operate on a VFO or Memory channel, while periodically checking a user-defined

Memory Channel for activity. If a station is received on the Memory Channel which is

strong enough to open the Squelch, the scanner will pause on that station in accordance

with the Scan-Resume mode set via Set Mode Item 35: RESUME. See page 35.

Here is the procedure for activating Priority Channel Dual Watch operation:

VFO Priority

Recall the memory channel you wish to use as the “Priority” frequency.

Now, set the radio to the VFO mode by pressing the [V/M(PRI)] key.

Press the [F/W] key, then press the [V/M(PRI)] key to activate the VFO Priority mode.

The display will remain on the VFO frequency, but every five

seconds the radio will check the Priority Channel (memory channel)

for activity.

Press [F/W] .

[V/M(PRI)] again to disable the VFO Priority mode.

Memory Channel Priority

Store the frequency you wish to be the “Priority” Channel into memory channel “1.”

Now, set the radio for operation on another memory channel.

Press the [F/W] key, then press the [V/M(PRI)] key to activate the Memory Priority

mode. The display will remain on the current memory channel

frequency, but every five seconds the radio will check the Priority

Channel (memory channel “1”) for activity.

Press [F/W] .

[V/M(PRI)] again to disable the Memory Priority mode.

When the Memory Bank feature is activated, the FT-60R will check the lowest memory

channel in the current Memory Bank as the priority channel.

HOME Channel Priority

Recall the memory channel you wish to use as the “Priority” frequency.

Now set the radio for operation on a HOME channel by pressing the [F/W] key followed

by [HM/RV].

Press the [F/W] key, then press the [V/M(PRI)]key to activate

the HOME Priority mode. The display will remain on the HOME

channel frequency, but every five seconds the radio will check

the Priority Channel (memory channel) for activity.

Press [F/W] .

[V/M(PRI)] again to disable the HOME Priority mode.

FT-60R OPERATING MANUAL

SCANNING

“PRIORITY CHANNEL” SCANNING

(DUAL WATCH)

WX Channel Priority

Recall the memory channel you wish to use as the “Priority” frequency.

Now, set the radio for operation on a WX channel by pressing and holding in the

[1(SQ TYP)] key for one second.

Press the [F/W] key, then press the [V/M(PRI)] key to activate the WX Priority mode.

The display will remain on the WX channel frequency, but every

five seconds the radio will check the Priority Channel

(memory channel) for activity.

Press [F/W] .

[V/M(PRI)] again to disable the WX Priority mode.

Priority Revert Mode

During Priority channel operation (Dual Watch), a special feature is available which

will allow you to move to the Priority channel instantly, without waiting for activity

to appear on the Priority channel.

When this feature is enabled, and Priority monitoring is engaged, just press the

PTT switch; operation will instantly revert to the Priority channel.

To enable the Priority Revert operation:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 39:

PRI.RVT.

3. Press the [F/W] key momentarily to enable adjustment

of this Set Mode Item.

4. Rotate the DIAL knob to set this Set Mode Item to “RVT.

ON.”

When you have made your selection, press the PTT key to save the setting and

exit to normal operation.

To disable the Priority Revert operation, just repeat the above procedure, rotating

the DIAL knob to select “RVT.OFF” in step 4 above.

FT-60R OPERATING MANUAL

SCANNING

AUTOMATIC LAMP ILLUMINATION

ON SCAN STOP

The FT-60R will automatically illuminate the LCD/Keypad Lamp whenever the scanner

stops on a signal; this allows you to see the frequency of the incoming signal better at night.

Note that this will, of course, increase the battery consumption, so be sure to switch it off

during the day (the default condition for this feature is “ON”).

The procedure for disabling the Scan Lamp is:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 44: SCN.LMP.

3. Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to set this Set Mode Item to “OFF.”

When you have made your selection, press the PTT key to save

the setting and exit to normal operation.

BAND EDGE BEEPER

The FT-60R will automatically “beep” when a band edge is encountered during scanning

(either in standard VFO scanning or during PMS operation). You may also enable this

feature (band edge beeper) to operate when the frequency reaches the band edge while

tuning using the DIAL knob.

The procedure for enabling the Band-Edge Beeper is:

Press the [F/W] key, then press the [0(

)SET] key to enter the

Set mode.

Rotate the DIAL knob to select Set Mode Item 19: EDG.BEP.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to set this Set Mode Item to “BEP. ON.”

When you have made your selection, press the PTT key to save the setting and exit to

normal operation.

FT-60R OPERATING MANUAL

EPCS (ENHANCED PAGING & CODE SQUELCH)

The FT-60R includes an Enhanced CTCSS tone encoder/decoder and a dedicated microprocessor

providing paging and selective calling feature. This allows you to place a call to

a specific station (Paging), and to receive calls of your choice directed only to you (Code

Squelch).

The paging and code squelch systems use two pairs of (alternately switched) CTCSS tones

which are stored in the pager memories. Basically, your receiver remains silent until it

receives the CTCSS tone pair that matches those stored in the Receiving Pager Memory.

The squelch then opens so the caller is heard, and the paging ringer immediately sounds, if

activated. When you close the PTT switch to transmit, the CTCSS tone pair which is

stored in the Transmitting Pager Memory will be transmitted automatically.

On the paged radio, the squelch will close automatically after the incoming page ends.

Meanwhile, on the paging radio, the Enhanced Paging and Code Squelch system will be

disabled after the PTT switch is released after the paging transmission. You may re-activate

the Enhanced Paging and Code Squelch system again using Set Mode Item 29: PAGER,

if desired.

Storing the CTCSS Tone Pairs for EPCS Operation

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 31: PAG.CDR

for the Receiving CTCSS Tone Pair or Set Mode Item 32:

PAG.CDT for the Transmitting CTCSS Tone Pair.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to set the CTCSS Tone number which

corresponds tothe first tone of the CTCSS Tone Pair.

Press the [.(MHz)] or [.(MHz)] key, then rotate the DIAL

knob to set the CTCSS Tone number which corresponds to the

second tone of the CTCSS Tone Pair.

Press the PTT switch to save the new setting and exit to normal

operation.

CTCSS TONE NUMBER

The FT-60R

does not recognize

the order of

the 1st tone and the 2nd

tone. In other words, for

example, the FT-60R considers

both CTCSS pairs

“10, 35” and “35, 10” to

be identical.

No. Hz No. Hz No. Hz No. Hz No. Hz

01 67.0 11 94.8 21 131.8 31 171.3 41 203.5

02 69.3 12 97.4 22 136.5 32 173.8 42 206.5

03 71.9 13 100.0 23 141.3 33 177.3 43 210.7

04 74.4 14 103.5 24 146.2 34 179.9 44 218.1

05 77.0 15 107.2 25 151.4 35 183.5 45 225.7

06 79.7 16 110.9 26 156.7 36 186.2 46 229.1

07 82.5 17 114.8 27 159.8 37 189.9 47 233.6

08 85.4 18 118.8 28 162.2 38 192.8 48 241.8

09 88.5 19 123.0 29 165.5 39 196.6 49 250.3

10 91.5 20 127.3 30 167.9 40 199.5 50 254.1

FT-60R OPERATING MANUAL

EPCS (ENHANCED PAGING & CODE SQUELCH)

Activating the Enhanced Paging & Code Squelch System

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 29: PAGER.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to select PAG. ON.

Press the PTT switch to save the new setting and activate the

Enhanced Paging & Code Squelch.

To disable the Enhanced Paging & Code Squelch, just repeat the above procedure,

rotating the DIAL knob to select “PAG.OFF” in step 4 above.

1) In the factory default configuration, you may recall Set Mode Item 29:

PAGER by pressing [F/W] .

[7(P1)].

2) During Enhanced Paging & Code Squelch operation, you may set up the

FT-60R such that a ringing “bell” sound alerts you to the fact that a call is coming in, as

described previously. See page 25 for details.

Paging Answer Back

When you press the PTT switch to respond to a page call, the FT-60R transmits the same

CTCSS tone pair. This tone pair will open the Code Squelch of the calling station. If you

prefer, you can have the FT-60R respond to page calls automatically (“transpond”).

To enable this feature:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 30: PAG.ABK.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to select ABK. ON.

Press the PTT switch to save the new setting and exit to normal

operation.

The Paging Answer Back feature constitutes a form of “remote control” operation

that may be restricted to certain frequencies. U.S. users should confirm

the current status of §97.201(b) of the FCC’s rules governing the Amateur

service before utilizing this feature on the 144 MHz band.

FT-60R OPERATING MANUAL

EMERGENCY FEATURE

EMERGENCY CHANNEL OPERATION

The FT-60R includes an “Emergency” feature which may be useful if you have someone

monitoring on the same frequency as your transceiver’s UHF “Home” channel. See page

29 for details on setting the Home channel.

The “Emergency” feature is activated by pressing and holding in the [4(RPT)] key for one

second. When this is done, (A) the radio is placed on the UHF amateur band Home channel,

(B) it emits a loud “Alarm” sound (the volume is controlled by the VOL knob), (C) it

flashes the LCD/keypad lamp, (D) if you press the PTT switch, you will disable the Emergency

feature temporarily; you can then transmit on the UHF Home channel, and (E) two

seconds after the PTT release, the Emergency feature will resume.

To disable the “Emergency” feature, press the [F/W] key momentarily or turn the radio off

by rotating the VOL knob fully counter-clockwise into the click-stop position.

Use this feature if you are out for a walk and want a quick way of alerting a family member

as to a dangerous situation. The alarm sound may discourage an attacker and allow you to

escape.

1) Be sure to arrange with a friend or family member to be monitoring on the

same frequency, as there will be no identification sent via the Emergency

alarm sound. And do not transmit the alarm tone except in a true emergency!

2) The “Emergency” feature may be changed to another function via Set Mode Item 19:

EMG S; see page 72 for details.

3) If you place the radio in the “VHF Only” mode (see page 62 for details), the radio will

transmit on the VHF Home channel when you press the PTT switch.

EMERGENCY AUTOMATIC ID (EAI) FEATURE

The Emergency Automatic ID (EAI) feature can be used for searching for persons who are

incapacitated in disasters like earthquakes, especially search-and-rescue personnel who

may have become injured in a debris field. In such cases, if another searcher sends out a

unique command (CTCSS tone pair), the radio of the incapacitated party, who may not be

able to speak or even press the PTT switch, will automatically cause the injured party’s

radio to transmit, so others may perform direction-finding and effect a rescue. The callsign

of the incapacitated person will also be transmitted, to assist the rescue team.

If an emergency group is working in a dangerous area, all members should engage the EAI

feature on their transceiver, so that others can provide assistance to a fallen team member,

if necessary.

The Emergency Automatic ID (EAI) Feature has two operating modes: (1) Interval mode

and (2) Continuous mode.

FT-60R OPERATING MANUAL

EMERGENCY FEATURE

EMERGENCY AUTOMATIC ID (EAI) FEATURE

In the Interval mode, when the FT-60R receives the CTCSS tone pair which is stored in

the Receiving Pager Code Memory (configured via Set Mode Item 31: PAG.CDR) on the

frequency which is stored in Memory Channel “000,” the radio will automatically transmit

a brief (0.5 second) beep tone every 2.5 seconds until the EAI timer expiration at the

power level stored in that memory channel; it is NOT necessary for the incapacitated person

to press the PTT switch. Furthermore, if your call sign is stored in the radio by Set

Mode Item 11: CW WRI, the radio will transmit your callsign on the air when this feature

is first engaged by the remote page, and every 10 minutes thereafter.

In the Continuous mode, when the FT-60R receives the CTCSS tone pair which is stored

in the Receiving Pager Code Memory (configured via Set Mode Item 31: PAG.CDR) on

the frequency which is stored in Memory Channel “000,” the radio will automatically

transmit continuously, until the EAI timer expiration, at the power level stored in that

memory channel; it is NOT necessary for the incapacitated person to press the PTT switch.

Furthermore, if your call sign is stored in the radio by Set Mode Item 11: CW WRI, the

radio will transmit your callsign on the air when this feature is first engaged by the remote

page, and every 10 minutes thereater.

The “callsign” ID can be changed to any desired sequence of characters, such as a name.

After sending the callsign or name, the radio will repeatedly transmit three tones for a user-

defined period of time (between 1 and 30 minutes). The callsign or name will be transmitted

every 10 minutes.

The Emergency Automatic ID (EAI) Feature requires that you (1) store the CTCSS Tone

Pair into the Receiving Pager Memory (see page 44 for procedure), and (2) store the desired

UHF coordination frequency into Memory Channel “000” (see page 28 for procedure).

To enable this feature:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 18: EAI.

3. Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to select the desired EAI mode (Interval

EAI or Continuous EAI) and its transmit time (1-10, 15, 20, 30,

40, and 50 minutes) or OFF.

Press the PTT switch to save the new setting and exit to normal operation.

To disable the Emergency Automatic ID feature, just repeat the above procedure, rotating

the DIAL knob to select “OFF” in step 4 above.

When the Emergency Automatic ID feature is activated, the “

icon will blink in the LCD.

”

FT-60R OPERATING MANUAL

SMART SEARCH OPERATION

The Smart Search feature allows you to load frequencies automatically according to where

activity is encountered by your radio. When Smart Search is engaged, the transceiver will

search above and below your current frequency, storing active frequencies as it goes (without

stopping on them even momentarily); these frequencies are stored into a special Smart

Search memory bank, consisting of 31 memories (15 above the current frequency, 15 below

the current frequency, plus the current frequency itself).

Two basic operating modes for Smart Search are available:

SINGLE:

In this mode, the transceiver will sweep the current band once in each direction

starting on the current frequency. All channels where activity is present will be

loaded into the Smart Search memories; whether or not all 31 memories are

filled, the search will stop after one sweep in each direction.

CONT:

In this mode, the transceiver will make one pass in each direction as with One-

Shot searching; if all 31 channels are not filled after the first sweep, however, the

radio will continue sweeping until they are all filled.

Setting the Smart Search Mode

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 42: S SRCH.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to select the desired Smart Search mode

(see above).

When you have made your selection, press the PTT switch to

save the setting and exit to normal operation.

Storing Smart Search Memories

Set the radio to the VFO mode. Be sure that you have the Squelch adjusted properly

(so that band noise is quieted).

Press and hold in the [3(TX PO)] key for one second to begin the Smart Search scanning.

As active channels are detected, you will observe the number of “loaded” channels

increasing in the regular memory channel window.

4. Depending on the mode you set for Smart Search operation

(“SINGLE” or “CONT”), the Smart Search scan will eventually

terminate, and the LCD will revert to Smart Search Memory Channel “C.”

To recall the Smart Search memories, rotate the DIAL knob to choose from among the

frequencies stored by Smart Search.

To return to normal operation, press the [V/M(PRI)] key.

Smart Search is a great tool when visiting a city for the first time. You don’t

need to spend hours looking up repeater frequencies from a reference guidebook.

. .just ask your FT-60R where the action is!

FT-60R OPERATING MANUAL

INTERNET CONNECTION FEATURE

The FT-60R can be used to access a “node” (repeater or base station) which is tied into the

Vertex Standard WIRES™ (Wide-Coverage Internet Repeater Enhancement System) network,

operating in the “SRG” (Sister Radio Group) mode. Details may be found at the

WIRES-II Web site: http://www.vxstd.com/en/wiresinfo-en/. This feature may also be used

to access other systems, as described below.

Press the [0(

)SET] key momentarily to activate the Internet

Connection feature. The “

” icon will appear in the upper right

corner of the display.

Press and hold in the [0(

)SET] key for one second, then rotate the DIAL knob to

select the access number (ICOD “0” ~ “9,” “A,” “B,” “C,” “D,” “E (.),” “F (#),”)

corresponding to the WIRES™ node to which you wish to establish an Internet link

(ask the node or repeater owner/operator if you don’t know the

access number in the network). Now press the PTT switch to

exit from the selection mode.

With the Internet Connection feature activated (as in step 1 above), the FT-60R will

generate a brief (0.1 second) DTMF tone according to your selection in step 2. This

DTMF tone is sent at the beginning of every transmission to establish or maintain the

link to the local WIRES™ node operating in the SRG mode.

To disable the Internet Connection feature, press the [0(

)SET] key momentarily

(the “

” icon will disappear from the display).

If other users report that you always have a DTMF “beep” at the beginning

of each transmission, and you are not operating in conjunction with Internet

access, disable this function via step (4) above.

You may access other Internet Link Systems (including WIRES™ in the “FRG” mode)

that use a DTMF string for access.

Load the DTMF tones which you wish to use for Internet-link access into a DTMF

Autodial memory register. For purposes of this example, we will use “#123” as the

access code.

A. Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 17: DT WRT.

Press the [F/W] key to enable adjustment of this Set Mode

Item.

Rotate the DIAL knob to select the DTMF Memory register

into which you wish to store the access code.

Press the [F/W] key momentarily. The first digit will blink.

Rotate the DIAL knob to select “F” (representing DTMF

“#”: the first digit of the DTMF string).

Press the [F/W] key momentarily to accept the first digit

and move to the second digit of the DTMF string.

FT-60R OPERATING MANUAL

INTERNET CONNECTION FEATURE

Repeat the previous steps until you have completed the access

code (“#123”).

Press and hold in the [F/W] key for one second to save the

setting.

Press the PTT switch to save the setting and exit to normal operation.

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode again.

Rotate the DIAL knob to select Set Mode Item 21: I NET.

5. Press the [F/W] key to enable adjustment of this Set Mode Item.

Rotate the DIAL knob to set this Set Mode Item to “INT.MEM”

(thus activating the “Other Internet Link System” mode).

Press the PTT switch to save the new settings.

Press the [0(

)SET] key momentarily to activate the Internet

Connection feature. The “

” icon will appear in the upper right

corner of the display.

Press and hold in the [0(

)SET] key for one second, rotate the

DIAL knob to select the DTMF access number (“IMEM 1” ~ “IMEM 9”) corresponding

to the Internet link repeater to which you wish to establish

an Internet link, then press the PTT switch momentarily to lock

in the selected access number.

10.

Once the Internet Connection feature is activated per step 8

above, you may now press the [0(

)SET] key, while you are

transmitting, to send out the selected DTMF string (to establish

the link to the desired Internet-link mode).

11. To return to the WIRES™ mode, repeat steps 3 - 6 above, selecting “INT.COD” in step

FT-60R OPERATING MANUAL

ARTS™ (AUTOMATIC RANGE TRANSPONDER SYSTEM)

The ARTS™ feature uses DCS signaling to inform both parties when you and another

ARTS™-equipped station are within communications range. This may be particularly useful

during Search-and Rescue situations, where is important to stay in contact with other

members of your group.

Both stations must set up their DCS codes to the same code number, then activate their

ARTS™ feature using the command appropriate for their radio. Alert ringers may be activated,

if desired.

Whenever you push the PTT, or every 25 (or 15) seconds after ARTS™ is activated, your

radio will transmit a signal which includes a (subaudible) DCS signal for about 1 second. If the

other radio is in range, the beeper will sound (if enabled) and the display will show “IN.RNG”

as opposed to the out of range display “OUT.RNG” in which ARTS™ operation begins.

Whether you talk or not, the polling every 15 or 25 seconds will

continue until you de-activate ARTS™. Every 10 minutes, moreover,

you can have your radio transmit your callsign via CW, so as to

comply with identification requirements. When ARTS™ is de-activated,

DCS will also be deactivated (if you were not using it previ

ously in non-ARTS™ operation).

If you move out of range for more than one minute (four pollings), your radio will sense

that no signal has been received, three beeps will sound, and the display will revert to

“OUT.RNG.” If you move back into range, your radio will again beep, and the display will

change back to the “IN.RNG” indication.

During ARTS™ operation, your operating frequency will continue to be displayed, but no

changes may be made to it or other settings; you must terminate ARTS™ in order to resume

normal operation. This is a safety feature designed to prevent accidental loss of

contact due to channel change, etc.

Basic ARTS™ Setup and Operation

Set your radio and the other radio(s) to the same DCS code number, per the discussion

on page 23.

Press and hold in the [2(CODE)] key for one second. You will

observe the “OUT.RNG” display on the LCD below the operating

frequency. ARTS™ operation has now commenced.

Every 25 seconds, your radio will transmit a “polling” call to the other station. When

that station responds with its own ARTS™ polling signal, the

display will change to “IN.RNG” to confirm that the other station’s

polling code was received in response to yours.

Press the [F/W] key momentarily to exit ARTS™ operation and resume normal functioning

of the transceiver.

FT-60R OPERATING MANUAL

ARTS™ (AUTOMATIC RANGE TRANSPONDER SYSTEM)

ARTS™ constitutes a form of “remote control” operation that may be restricted

to certain frequencies. U.S. users should confirm the current status

of §97.201(b) of the FCC’s rules governing the Amateur service before utilizing

this feature on the 144 MHz band.

ARTS™ Polling Time Options

The ARTS™ feature may be programmed to poll every 25 seconds (default value) or 15

seconds. The default value provides maximum battery conservation, because the polling

signal is sent out less frequently. To change the polling interval:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 3: AR INT.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to select the desired polling interval (15

or 25 seconds).

When you have made your selection, press the PTT switch to

save the new setting and exit to normal operation.

ARTS™ Alert Beep Options

The ARTS™ feature allows two kinds of alert beeps (with the additional option of turning

them off), so as to alert you to the current status of ARTS™ operation. Depending on your

location and the potential annoyance associated with frequent beeps, you may choose the

Beep mode which best suits your needs. The choices are:

INRANG: The beeps are issued only when the radio first confirms that you are within

range, but does not re-confirm with beeps thereafter.

ALWAYS: Every time a polling transmission is received from the other station, the alert

beeps will be heard.

OFF: No alert beeps will be heard; you must look at the display to confirm current

ARTS™ status.

To set the ARTS™ Beep mode, use the following procedure:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 2: AR BEP.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to select the desired ARTS™ Beep mode

(see above).

5. When you have made your selection, press the PTT switch to

save the new setting and exit to normal operation.

FT-60R OPERATING MANUAL

ARTS™ (AUTOMATIC RANGE TRANSPONDER SYSTEM)

CW Identifier Setup

The ARTS™ feature includes a CW identifier, as discussed previously. Every ten minutes

during ARTS™ operation, the radio can be instructed to send “DE (your callsign) K” if

this feature is enabled. The callsign field may contain up to 6 characters.

Here’s how to program the CW Identifier:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 11: CW WRT.

letter/number and move on to the next character.

Repeat the previous step, as many times as necessary, to complete

your callsign. If you make a mistake, press the [.(MHz)]

key to move back to the previous letter/number’s slot, then re-

select the correct letter/number.

When you have finished entering your entire callsign and it contains

less than 6 characters, press and hold in the [F/W] key for one second to confirm

the callsign. (if you callsign has exactly 6 characters, you do not need to press and hold

in [F/W] in this step).

Press the PTT switch to save the settings and exit to normal operation.

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode again.

10. Rotate the DIAL knob to select Set Mode Item 10: CWID.

3. Press the [F/W] key momentarily to display any previously-stored

callsign.

Press the [F/W] key again to clear any previous callsign.

Rotate the DIAL knob to select the first letter/number of your

callsign, then press the [F/W] key momentarily to save the first

CW ID function).

13.

Press the PTT switch to save the settings and exit to normal

operation.

You may check your work by monitoring the entered callsign. To do this,

repeat steps 1- 7 above, then press the MONI switch.

11. Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

12.

Rotate the DIAL knob to set this Item to “TX ON” (to enable the

FT-60R OPERATING MANUAL

DTMF OPERATION

The FT-60R’s 16-button keypad allows easy DTMF dialing for Autopatch, repeater control,

or Internet-link access purposes. Besides numerical digits [0] through [9], the keypad

includes the [.] and [#] digits, plus the [A], [B], [C], and [D] tones often used for repeater

control.

Manual DTMF Tone Generation

You can generate DTMF tones during transmission manually.

Press the [F/W] key, then press the [9(DTMF)] key to disable

the DTMF Autodialer, if necessary. The “CODE” indication will

appear in the display for a moment.

Press the PTT switch to begin transmission.

While transmitting, press the desired numbers on the keypad.

When you have sent all the digits desired, release the PTT switch.

DTMF Autodialer

Nine DTMF Autodial memories are provided, allowing you to store telephone numbers for

autopatch use. You can also store short autopatch or Internet-link access code streams so as

to avoid having to send them manually.

Here is the DTMF Autodial storage procedure:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 17: DT WRT.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to select the DTMF Memory register into

which you wish to store this DTMF string.

Press the [F/W] key momentarily to begin DTMF Memory entry

into the selected register.

Rotate the DIAL knob to select the first digit of the DTMF string.

Selectable entries are 0 - 9, and A - F, with E and F representing

DTMF “*” and “#” tones respectively.

Press the [F/W] key to accept the first digit and move to the next digit of the DTMF

string.

Repeat steps 5 and 6 until you have completed the telephone

number.

If you make a mistake, press the [.(MHz)] key to move back to

the previous digit, then re-select the correct number.

10. If the telephone number made up of numbers only, you may key in the telephone

number directly from the keypad.

11.

Press and hold in the [F/W] key for one second to save the setting.

FT-60R OPERATING MANUAL

DTMF OPERATION

12.

If you store other numbers, repeat steps 4- 10 above, using a different DTMF memory

13.

When all required DTMF memories are filled to your satisfaction, press the PTT

switch to save the settings and exit to normal operation

To send the telephone number:

Press the [F/W] key, then press the [9(DTMF)] key to activate

the DTMF Autodialer. The “MEM” indication display will ap

pear in the display for a moment.

While the DTMF Autodialer is activated, first press the PTT switch, then press the

numerical key ([1] through [9]) corresponding to the DTMF memory string you wish

to send. Once the string begins, you may release the PTT switch, as the transmitter will

be held “on the air” until the DTMF string is completed.

To disable the DTMF Autodialer, press [F/W] .

[9(DTMF)] again. The “CODE”

indication will appear in the display for a moment.

You can change the DTMF Audodialer sending speed, using Set Mode Item 16: DT SPD.

See page 71 for details.

You can also set a longer delay between the time you press the numerical key (corresponding

to the DTMF memory string; with PTT switch pressed) and the instant when the first

DTMF digit is sent, using Set Mode Item 15: DT DLY. See page 71 for details.

FT-60R OPERATING MANUAL

MISCELLANEOUS SETTINGS

PASSWORD

The FT-60R provides the password feature which can minimize the chance that your transceiver

could be used by an unauthorized party.

When the password feature is activated, the radio will ask for the four digit password to be

entered when the radio is first turned on. You must enter the four

digit password from the keypad. If the wrong password is entered,

the microprocessor will shut down the radio automatically.

To enter the password , use the following procedure:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

2. Rotate the DIAL knob to select Set Mode Item 34: PSWD W.

3. Press the [F/W] key momentarily to display any previously-stored

password.

Press the [F/W] key again to clear any previous password.

Rotate the DIAL knob to select the first digit of the desired number/

letter (0-9, A, B, C, D, E (substitute for “.”), and F (substitute

for “#”).

Press the [F/W] key to move to the next digit.

Repeat steps 5 and 6 to program the remaining numbers/letters

of the desired password.

If you make a mistake, press the [.(MHz)] key to move back to

the previous digit, then re-select the correct number/letter.

If your password is made up of numbers only, you may enter your password directly

from the keypad. For example, to enter the “1234” as your password, press [1] .

[2]

[3] .

[4].

10.

When you have finished entering the password, press the PTT switch to save the new

setting and exit to normal operation.

We recommend that you to write down the password number, and keep it in a safe place

you can easily find if you forget your password.

To Activate the Password feature:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 33: PSWD.

Press the [F/W] key momentarily to enable adjustment of this

Item.

Rotate the DIAL knob to set this Set Mode Item to “PWD. ON.”

When you have made your selection, press the PTT switch to

save the new setting and exit to normal operation.

If you wish to disable the Password feature, just repeat the above procedure, rotating

the DIAL knob to select “PWD.OFF” in step 4 above.

FT-60R OPERATING MANUAL

MISCELLANEOUS SETTINGS

PASSWORD

If you forget the password number, you may turn on the transceiver by performing

the “All Reset” procedure (see page 64). However, the FT-60R will

clear the password, as well as all memories, and will restore all other settings

to factory defaults.

PROGRAMMING

THE KEY ASSIGNMENTS

Default FT-60R Set Mode Items have been assigned (at the factory) to the [7(P1)] and

[8(P2)] keys. These may be changed by the user, if you wish to assign another Set Mode

Item to either or both of these keys.

To change the assignment of a key’s Set Mode Item:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select the Set Mode Item which you wish to assign to the key

as a Menu short-cut.

Press and hold in the [7(P1)] or [8(P2)] key for one second to assign the Set Mode

Item to the [7(P1)] or [8(P2)] key.

The following Set Mode Items may not be assigned to the [7(P1)] and [8(P2)] keys.

Set Mode Item 11: CW WRT

Set Mode Item 17: DT WRT

Set Mode Item 33: PSWD W

CHANGING

THE CHANNEL STEPS

The FT-60R’s synthesizer provides the option of utilizing channel steps of 5/10/12.5/15/

20/25/50/100 kHz per step, as well as an automatic step selection based on the current

operating frequency (“AUTO”), any number of which may be important to your operating

requirements. The FT-60R is set up at the factory in the “AUTO” configuration, which

probably is satisfactory for most operation. However, if you need to change the channel

step increments, the procedure to do so is very easy.

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 49: STEP.

Press the [F/W] key momentarily to enable adjustment of this

Item.

Rotate the DIAL knob to select the new channel step size.

5. When you have made your selection, press the PTT switch to

save the new setting and return to normal operation.

FT-60R OPERATING MANUAL

MISCELLANEOUS SETTINGS

CHANGING

THE RECEIVING MODE

The FT-60R provides for automatic mode changing when the radio is tuned to different

operating frequencies. However, should an unusual operating situation arise in which you

need to change between the available operating modes (FM and AM), here is the procedure

for doing so:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 40: RX MOD.

Press the [F/W] key momentarily to enable adjustment of this

Item.

Rotate the DIAL knob to select the new operating mode. The

available selections are:

AUTO:Automatic mode setting per default values for the selected

frequency range.

FM: Frequency Modulation

AM: Amplitude Modulation

When you have made your selection, press the PTT switch to save the new setting and

return to normal operation.

Unless you have a compelling reason to do so, leave the Automatic Mode

Selection feature on so as to save time and trouble when changing bands. If

you make a mode change for a particular channel or station, you can always

store that one channel into memory, as the mode setting will be memorized along with

the frequency information.

FT-60R OPERATING MANUAL

MISCELLANEOUS SETTINGS

RECEIVE BATTERY SAVER SETUP

An important feature of the FT-60R is its Receive Battery Saver, which “puts the radio to

sleep” for a time interval, periodically “waking it up” to check for activity. If somebody is

talking on the channel, the FT-60R will remain in the “active” mode, then resume its

“sleep” cycles. This feature significantly reduces quiescent battery drain, and you may

change the amount of “sleep” time between activity checks using the Set Mode:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 41: RXSAVE.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to select the desired “sleep” duration.

The selections available are 200 ms, 300 ms, 500 ms, 1 second,

2 seconds, or OFF. The default value is 200 ms.

When you have made your selection, press the PTT switch to save the new setting and

exit to normal operation.

When you are operating on Packet, switch the Receive Battery Saver OFF, as

the sleep cycle may “collide” with the beginning of an incoming Packet transmission,

causing your TNC not to receive the full data burst.

TX BATTERY SAVER

The FT-60R also includes a useful Transmit Battery Saver, which will automatically lower

the power output level when the last signal received was very strong. For example, when

you are in the immediate vicinity of a repeater station, there generally is no reason to use

the High Power output in order to achieve full-quieting access to the repeater. With the

Transmit Battery Saver, the automatic selection of Low Power operation conserves battery

drain significantly.

To activate the Transmit Battery Saver:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 53: TXSAVE.

3. Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to set this Set Mode Item to “SAV. ON”

(thus activating the Transmit Battery Saver).

5. When you have made your selection, press the PTT switch to

save the new setting and exit to normal operation.

FT-60R OPERATING MANUAL

MISCELLANEOUS SETTINGS

DISABLING

THE TX/BUSY INDICATOR

Further battery conservation may be accomplished by disabling the TX indicator while

transmitting and disabling the BUSY indicator while receiving a signal. Use the following

procedure:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 8: BSY.LED if

you wish to disable the BUSY indicator or Set Mode Item 52:

TX.LED if you wish to disable the TX indicator.

3. Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to set this Set Mode Item to “LED.OFF”

(thus disabling the BUSY or TX indicator).

When you have made your selection, press the PTT switch to save the new setting and

exit to normal operation.

If you wish to re-enable the TX/BUSY Indicator, just repeat the above procedure,

rotating the DIAL knob to select “LED. ON” in step 4 above.

AUTOMATIC POWER-OFF

(APO) FEATURE

The APO feature helps conserve battery life by automatically turning the radio off after a

user-defined period of time within which there has been no dial or key activity. The available

selections for the time before power-off are 0.5 to 12.0 hours in 0.5 hour multiple, as

well as APO Off. The default condition for the APO is OFF, and here is the procedure for

activating it:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 1: APO.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to select the desired time period after

which the radio will automatically shut down.

When you have made your selection, press the PTT switch to

save the new setting and exit to normal operation.

When the APO is activated, the “

” icon will appear at the upper

right corner on the LCD. If there is no action by you within the time

interval programmed, the microprocessor will shut down the radio

automatically.

Rotate the VOL/PWR knob counter-clockwise to the “off” position, then clockwise out of

the click-stop, to turn the radio on after an APO shutdown.

FT-60R OPERATING MANUAL

MISCELLANEOUS SETTINGS

TRANSMITTER TIME-OUT TIMER

(TOT)

The TOT feature provides a safety switch which limits transmission time to a pre-programmed

value. This will promote battery conservation by not allowing you to make excessively-

long transmissions, and in the event of a stuck PTT switch (perhaps if the radio

or a Speaker/Mic is wedged between car seats) it can prevent interference to other users as

well as battery depletion. As configured at the factory the TOT feature is set to OFF, and

here is the procedure for activating it:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 51: TOT.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to set the Time-Out Timer to the desired

“Maximum TX” time (between 1 and 30 minutes), or OFF.

5. When you have made your selection, press the PTT switch to

save the new setting and exit to normal operation.

1) When your transmission time is within 10 seconds of the Time-Out Timer

expiration, an Alert bell will provide an audible warning from the speaker.

2) Since brief transmissions are the mark of a good operator, try setting up

your radio’s TOT feature for a maximum transmission time of one minute. This will

significantly improve battery life, too!

BUSY CHANNEL LOCK-OUT

(BCLO)

The BCLO feature prevents the radio’s transmitter from being activated if a signal strong

enough to break through the “noise” squelch is present. On a frequency where stations

using different CTCSS or DCS codes may be active, BCLO prevents you from disrupting

their communications accidentally (because your radio may be muted by its own Tone

Decoder). The default setting for the BCLO is OFF, and here is how to change that setting:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 5: BCLO.

Press the [F/W] key momentarily to enable adjustment of this

Set Mode Item.

Rotate the DIAL knob to set this Set Mode Item to “BCL. ON”

(thus activating the BCLO feature).

When you have made your selection, press the PTT switch to

save the new setting and exit to normal operation.

FT-60R OPERATING MANUAL

MISCELLANEOUS SETTINGS

MONO BAND OPERATION

You may place the radio in a “VHF Only” or “UHF Only” mode which will cause it to

function as a 144 MHz or 430 MHz Mono band transceiver.

To place the radio into the Mono band operation configuration:

Turn the radio off.

Press and hold in the MONI switch (just below the PTT switch) while turning the

radio on.

Rotate the DIAL knob to select the configuration mode menu:

F6 V-ONLY: The FT-60R will operate on the 144 MHz band

only.

F7 U-ONLY: The FT-60R will operate on the 430 MHz band

only.

Press the [F/W] key momentarily.

To return to normal operation, press and hold in the MONI switch while turning the radio

on, and then press the [F/W] key momentarily.

CHANGING

THE TX DEVIATION LEVEL

In many areas of the world, channel congestion has required that operating channels be

closely spaced. In such operating environments, it often is required that operators use

reduced deviation levels, so as to reduce the potential for interference to users on adjacent

channels. The FT-60R includes a simple method of accomplishing this:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select Set Mode Item 55: WID.NAR.

Set Mode Item.

Rotate the DIAL knob to set this Set Mode Item to “NARROW.”

In this configuration (HALF DEVIATION active), the

transmitter’s deviation will be approximately ±2.5 kHz, and the

received audio output level will be increased, for easier listening on the narrow signal.

When you have made your selection, press the PTT switch to save the new setting and

exit to normal operation.

The “normal” setting for the deviation (when this Menu Item is set to WIDE) is ±5 kHz.

3. Press the [F/W] key momentarily to enable adjustment of this

FT-60R OPERATING MANUAL

MISCELLANEOUS SETTINGS

DCS CODE INVERSION

The DCS system was first introduced in the commercial LMR (Land Mobile Radio) service,

where it is now in widespread use. DCS is sometime referred to by its different proprietary

names, such as DPL® (Digital Private Line®, a registered trademark of Motorola, Inc.).

DCS uses a codeword consisting of a 23-bit frame, transmitted (subaudible) at a data rate

of 134.4 bps (bit/sec). Occasionally, signal inversion can result in the complement of a

code to be sent or received. This prevents the receiver’s squelch from opening with DCS

enabled, as the decoded bit sequence would not match that selected for operation.

Typical situations that might cause inversion to occur are:

Connection of an external receiver preamplifier.

Operating through a repeater.

Connection of an external linear amplifier.

Note that code inversion does not mean that any of the above listed equipment is defective!

In certain amplifier configurations, the output signal (phase) is inverted from the input.

Small signal or power amplifiers having an odd number (1, 3, 5, etc.) of amplification

stages may result in inversion of a transmitted or received DCS code.

While under most circumstances this should not occur (amplifier designs and industry

standards take this into account), if you find that your receiver squelch does not open when

both you and the other station are using a common DCS code, you or

the other station (but not both) can try the following:

Press the [F/W] key, then press the [0(

)SET] key to enter the

Set mode.

Rotate the DIAL knob to select Set Mode Item 14: DCS.N/R.

3. Press the [F/W] key momentarily, then rotate the DIAL knob to

select one of the following modes:

T/RX N:Encoder, Normal; Decoder, Normal

RX R: Encoder, Normal; Decoder, Reverse (Inverted)

TX R: Encoder, Reverse (Inverted); Decoder, Normal

T/RX R: Encoder, Reverse (Inverted); Decoder, Reverse (Inverted)

When you have made your selection, press the PTT switch to save the new setting and

exit to normal operation.

Remember to restore the default setting to “T/RX N” (Encoder; Normal, Decoder;

Normal) when done.

FT-60R OPERATING MANUAL

RESET PROCEDURES

In the event of erratic operation of the transceiver, it is possible that data on the microprocessor

may have become corrupted. While this is a highly unusual situation, the only path

to recovery may involve resetting of the microprocessor. Here’s how to do this:

Turn the radio off.

Press and hold in the MONI switch (just below the PTT switch)

while turning the radio on.

Rotate the DIAL knob to select one choice from the reset menu:

F1 SETRST: Resets the Set (Menu) mode settings to their factory defaults.

F2 MEMRST:Clears the Memory settings to factory defaults.

F3 MB RST: Clears the Memory Bank Assignments.

F4 ALLRST: Clears all memories and other settings to factory defaults.

Press the [F/W] key momentarily to complete the reset procedure.

FT-60R OPERATING MANUAL

FT-60R OPERATING MANUAL 65

The FT-60R includes a convenient “Clone” feature, which allows the memory and configuration

data from one transceiver to be transferred to another FT-60R. This can be

particularly useful when configuring a number of transceivers for a public service operation.

Here is the procedure for Cloning one radio’s data to another:

1. Turn both radios off.

2. Connect the optional CT-27 Clone Cable between the MIC/SP jacks of the two radios.

3. Press and hold in the MONI switch (just below the PTT switch)

while turning the radios on. Do this for both radios (the order of

switch-on does not matter).

4. Rotate the DIAL job on each radio to select to “F8 CLONE,”

then press the [F/W] key momentarily.

5. The display will disappear for a moment, then the “CLONE”

notation will appear on the displays of both radios when the

Clone mode is successfully activated in this step.

6. On the Destination radio, press the MONI switch (“- -RX- -” will

appear on the LCD).

7. Press the PTT switch on the Source radio; “- -TX- -” will appear

on the Source radio, and the data from this radio will be transferred

to the other radio.

8. If there is a problem during the cloning process, “ERROR” will

be displayed. Check your cable connections and battery voltage,

and try again.

9. If the data transfer is successful, “CLONE” will reappear on both

displays. Turn both radios off and disconnect the cloning cable. You can then turn the

radios back on, and begin normal operation.

CLONING

CT-27

MIC/SP MIC/SP

SET (MENU) MOD E

The FT-60R Set Mode, already described in parts of many previous chapters, is easy to

activate and set. It may be used for configuration of a wide variety of transceiver parameters,

some of which have not been detailed previously. Use the following procedure to

activate the Set Mode:

Press the [F/W] key, then press the [0(

)SET] key to enter the Set mode.

Rotate the DIAL knob to select the Set Mode Item to be adjusted.

Press the [F/W] key momentarily to enable adjustment of the

Set Mode Item.

Rotate the DIAL knob to adjust or select the parameter to be

changed on the Set Mode Item selected in above step.

After completing your selection and adjustment, press the PTT switch momentarily to

save the new setting and exit to normal operation.

1) Some Set Mode Items (like Set Mode Item 50: TN FRQ) require that the

[F/W] key be pressed after setting of the parameter, and before exiting to

normal operation.

2) Two Set Mode Item numbers (In the factory default, Set Mode Item 29: PAGER, and

46: SKIP) will blink while selecting the Set Mode Item; this indicates that this Set Mode

Item has been assigned to the [7(P1)] or [8(P2)] key of the keypad.

SET MODE ITEM

FUNCTION

AVAILABLE VALUES

(DEFAULT: BOLD ITARIC)

1 [APO] Setting of the Automatic Power-Off feature. OFF / 0.5H - 12.0 H

2 [AR BEP] Selects the Beep option during ARTS operation. INRANG / ALWAYS / OFF

3 [AR INT] Selects the Polling Interval during ARTS operation. 25 SEC / 15 SEC

4 [ARS] Enables/Disables the Automatic Repeater Shift function. ARS. ON / ARS.OFF

5 [BCLO] Enables/Disables the Busy Channel Lock-Out feature. BCL. ON / BCL.OFF

6 [BEEP] Enables/Disables the beeper. KEY+SC / KEY / OFF

7 [BELL] Selects the number of CTCSS/DCS Bell ringer repetitions. OFF / 1T / 3T /

5T / 8T / CONT

8 [BSY.LED] Enables/Disables the BUSY LED while the Squelch is open. LED. ON / LED.OFF

9 [CLK.SFT] Shifting of the CPU clock frequency. SFT.OFF / SFT. ON

10 [CWID] Enables/disables the CW identifier during ARTS operation. TX OFF / TX ON

11 [CW WRT] Programs and activates the CW Identifier. --12

[DC VLT] Indicates the DC Supply Voltage. --13

[DCS.COD] Setting of the DCS code. 104 DCS codes (023)

14 [DCS.N/R] Enables/Disables “Inverted” DCS code decoding. T/RX N, RX R,

TX R, T/RX R

15 [DT DLY] Setting of the DTMF Autodialer Delay Time. 50MS / 100MS / 250MS /

450MS / 750MS / 1000MS

16 [DT SPD] Setting of the DTMF Autodialer Sending Speed. 50MS / 100MS

17 [DT WRT] Programming of the DTMF Autodialer. --18

[EAI] Enables/Disables the Emergency Automatic ID (EAI) Feature. INT. 1M - INT. 50M /

CON. 1M - CON.50M / OFF

19 [EDG.BEP] Enables/Disables the Band-edge beeper while selecting the

frequency via the DIAL knob.

BEP.OFF / BEP. ON

FT-60R OPERATING MANUAL

SET (MENU) MODE

SET MODE ITEM

FUNCTION

AVAILABLE VALUES

(DEFAULT: BOLD ITARIC)

20 [EMG S] Selects the alarm(s) utilized when the Emergency function is

engaged.

EMG.BEP / EMG.LMP /

EMG.B+L / EMG.CWT /

EMG.C+B / EMG.C+L /

EMG.ALL / OFF

21 [I NET] Selects the Internet Link Connection mode. INT.OFF / INT.COD / INT.MEM

22 [INT CD] Selects the Access Number (DTMF digit) for WIRES™

operation.

CODE 0 - CODE 9

(CODE 1)

23 [INT MR] Selects the memory register for an Access Number (DTMF

code) for non-WIRES™

d1 - d9

24 [LAMP] Selects the LCD/Keypad Lamp mode. KEY / 5SEC / TOGGLE

25 [LOCK] Selects the Control Locking lockout combination. LK KEY / LKDIAL / LK K+D /

LK PTT / LK P+K /

LK P+D / LK ALL

26 [M/T-CL] Selects the MONI key (just below the PTT switch) function. MONI / T-CALL

27 [NAME] Toggles the display indication between “frequency” and the

channel’s “Alpha/Numeric Tag.”

FREQ / ALPHA

28 [NM WRT] Stores Alpha-Numeric “Tags” for the Memory channels. --29

[PAGER] Enables/disables the Enhanced CTCSS Paging & Code

Squelch function.

OFF / ON

30 [PAG.ABK] Enables/disables the Answer Back function of the Enhanced

CTCSS Paging & Code Squelch.

ABK.OFF / ABK. ON

31 [PAG.CDR] Setting the Receiver Pager Code for the Enhanced CTCSS

Paging & Code Squelch.

(05_47)

32 [PAG.CDT] Setting the Transmitting Pager Code for the Enhanced CTCSS

Paging & Code Squelch.

(05_47)

33 [PSWD] Enables/disables the Password feature. PWD.OFF / PWD. ON

34 [PSWD W] Stores the password. --35

[RESUME] Selects the Scan Resume mode. BUSY / HOLD / TIME

36 [REV/HM] Selects the function of the [HM/RV] key. <REV> / <HOME>

37 [RF SQL] Adjusts the RF Squelch threshold level. S-1 / S-2 / S-3 / S-4 / S-5 / S6

/ S-8 / S-FULL / OFF

38 [RPT.MOD] Sets the Repeater Shift Direction. RPT.OFF / RPT.– / RPT. + (.)

39 [PRI.RVT] Enables/disables the Priority Revert feature. RVT.OFF / RVT. ON

40 [RX MOD] Selects the receiving mode. AUTO / FM / AM

41 [RXSAVE] Selects the Receive-mode Battery Saver interval (“sleep” ratio) 200 MS / 300 MS /

500 MS / 1 S / 2 S / OFF

42 [S SRCH] Selects the Smart Search Sweep mode. SINGLE / CONT

43 [SCN MD] Selects the Memory Scan channel-selection mode. ONLY / MEM

44 [SCN.LMP] Enables/Disables the Scan lamp while paused. ON / OFF

45 [SHIFT] Sets the magnitude of the repeater Shift. 0.00 - 99.95 MHz (.)

46 [SKIP] Selects the Memory Scan “Skip” channel-selection mode. OFF / SKIP / ONLY

47 [SPLIT] Enables/Disables split CTCSS/DCS coding. SPL.OFF / SPL. ON

48 [SQL.TYP] Selects the Tone Encoder and/or Decoder mode. OFF / TONE / TSQL /

REV TN / DCS

49 [STEP] Setting of the synthesizer steps. 5 / 10 / 12.5 / 15 / 20 / 25 / 50

/ 100 kHz, or AUTO

50 [TN FRQ] Setting of the CTCSS Tone Frequency. 50 CTCSS tones (100 Hz)

51 [TOT] Setting of the TOT time. 1MIN - 30MIN or OFF (6MIN)

52 [TX.LED] Enables/Disables the TX LED while the radio is transmitting. LED. ON / LED.OFF

53 [TXSAVE] Enables/Disables the Transmitter Battery Saver. SAV.OFF / SAV. ON

54 [VFO.BND] Enables or disables the VFO band edge limiting for the current

band.

BAND / ALL

55 [WID.NAR] Select Wide (±5 kHz) or Narrow (±2.5 kHz) TX Deviation. WIDE / NARROW

56 [WX ALT] Enables/Disables the Weather Alert Scan feature. ALT.OFF / ALT. ON

.: Depends on the transceiver version.

FT-60R OPERATING MANUAL

SET (MENU) MODE

REPEATER SETTING

SET MODE ITEM

AVAILABLE VALUES

(DEFAULT)

Enables/Disables the Automatic Repeater Shift function. 4 [ARS] ARS. ON / ARS.OFF

Sets the Repeater Shift Direction. 38 [RPT.MOD] RPT.OFF / RPT. – / RPT. + (.)

Sets the magnitude of the repeater Shift. 45 [SHIFT] 0.00 - 99.95 MHz (.)

CTCSS/DSC/DTMF SETTING

SET MODE ITEM

AVAILABLE VALUES

(DEFAULT)

Selects the number of CTCSS/DCS Bell ringer repetitions.

Setting of the DCS code.

Enables/Disables “Inverted” DCS code decoding.

Setting of the DTMF Autodialer Delay Time.

Setting of the DTMF Autodialer Sending Speed.

Programming of the DTMF Autodialer.

Enables/Disables split CTCSS/DCS coding.

Selects the Tone Encoder and/or Decoder mode.

Setting of the CTCSS Tone Frequency.

7 [BELL]

13 [DCS.COD]

14 [DCS.N/R]

15 [DT DLY]

16 [DT SPD]

17 [DT WRT]

47 [SPLIT]

48 [SQL.TYP]

50 [TN FRQ]

OFF / 1T / 3T / 5T / 8T / CONT

104 standard DCS codes (023)

T/RX N, RX R, TX R, T/RX R

50MS / 100MS / 250MS / 450MS /

750MS / 1000MS

50MS /100MS

–

SPL.OFF / SPL. ON

OFF / TONE / TSQL /

REV TN / DCS

50 standard CTCSS tones (100 Hz)

ARTS SETTING

SET MODE ITEM

AVAILABLE VALUES

(DEFAULT)

Selects the Beep option during ARTS operation.

Selects the Polling Interval during ARTS operation.

Enables/disables the CW identifier during ARTS operation.

Programs and activates the CW Identifier (used during ARTS

operation).

2 [AR BEP]

3 [AR INT]

10 [CWID]

11 [CW WRT]

INRANG / ALWAYS / OFF

25 SEC / 15 SEC

TX OFF / TX ON

–

MEMORY SETTING

SET MODE ITEM

AVAILABLE VALUES

(DEFAULT)

Toggles the display indication between “frequency” and the 27 [NAME] FREQ / ALPHA

channel’s “Alpha/Numeric Tag.”

Stores Alpha-Numeric “Tags” for the Memory channels. 28 [NM WRT] –

SCAN SETTING

SET MODE ITEM

AVAILABLE VALUES

(DEFAULT)

Selects the Scan Resume mode. 35 [RESUME] BUSY / HOLD / TIME

Enables/disables the Priority Revert feature. 39 [PRI.RVT] RVT.OFF / RVT. ON

Selects the Memory Scan channel-selection mode. 43 [SCN MD] ONLY / MEM

Enables/Disables the Scan lamp while paused. 44 [SCN.LMP] ON / OFF

Selects the Memory Scan “Skip” channel-selection mode. 46 [SKIP] OFF / SKIP / ONLY

Enables/Disables the Weather Alert Scan feature. 56 [WX ALT] ALT.OFF / ALT. ON

POWER SAVER SETTING

SET MODE ITEM

AVAILABLE VALUES

(DEFAULT)

Selects the Receive-mode Battery Saver interval (“sleep” 41 [RXSAVE] 200 MS / 300 MS / 500 MS /

ratio). 1 S / 2 S / OFF

Enables/Disables the Transmitter Battery Saver. 53 [TXSAVE] SAV.OFF / SAV. ON

WIRES™ SETTING

SET MODE ITEM

AVAILABLE VALUES

(DEFAULT)

Selects the Internet Link Connection mode. 21 [I NET] INT.OFF / INT.COD / INT.MEM

Selects the Access Number (DTMF digit) for WIRES™ op22

[INT CD] CODE 0 - CODE 9 (CODE 1)

eration.

Selects the memory register for an Access Number (DTMF 23 [INT MR] d1 - d9

digit) for non-WIRES™.

Enables/disables the Enhanced CTCSS Paging & Code 29 [PAGER] OFF / ON

Squelch function.

Enables/disables the Answer Back function of the Enhanced 30 [PAG.ABK] ABK.OFF / ABK. ON

CTCSS Paging & Code Squelch.

Setting the Receiver Pager Code for the Enhanced CTCSS 31 [PAG.CDR] –

Paging & Code Squelch.

Setting the Transmitting Pager Code for the Enhanced 32 [PAG.CDT] –

CTCSS Paging & Code Squelch.

.: Depends on the transceiver version.

FT-60R OPERATING MANUAL

SET (MENU) MODE

SWITCH/KNOB SETTING

SET MODE ITEM

AVAILABLE VALUES

(DEFAULT)

Enables/Disables the beeper.

Selects the LCD/Keypad Lamp mode.

Selects the Control Locking lockout combination.

Selects the MONI key (just below the PTT switch) function.

Selects the function of the [HM/RV] key.

6 [BEEP]

24 [LAMP]

25 [LOCK]

26 [M/T-CL]

36 [REV/HM]

KEY+SC / KEY / OFF

KEY / 5SEC / TOGGLE

LK KEY / LKDIAL / LK K+D / LK

PTT / LK P+K / LK P+D / LK ALL

MONI / T-CALL

MISCELLANEOUS SETTING

SET MODE ITEM

AVAILABLE VALUES

(DEFAULT)

Setting of the Automatic Power-Off feature.

Enables/Disables the Busy Channel Lock-Out feature.

Enables/Disables the BUSY LED while the Squelch is open.

Shifting of the CPU clock frequency.

Indicates the DC Supply Voltage.

Enables/Disables the Emergency Automatic ID (EAI) Feature.

Enables/Disables the Band-edge beeper while selecting the

frequency via the DIAL knob.

Selects the alarm(s) utilized when the Emergency function

is engaged.

Enables/disables the Password feature.

Stores the password.

Adjusts the RF Squelch threshold level.

Selects the receiving mode.

Selects the Smart Search Sweep mode.

Setting of the synthesizer steps.

Setting of the TOT time

Enables/Disables the TX LED while the radio is transmitting.

Enables or disables the VFO band edge limiting for the current

band.

Select Wide (±5 kHz) or Narrow (±2.5 kHz) TX Deviation.

1 [APO]

5 [BCLO]

8 [BSY.LED]

9 [CLK.SFT]

12 [DC VLT]

18 [EAI]

19 [EDG.BEP]

20 [EMG S]

33 [PSWD]

34 [PSWD W]

37 [RF SQL]

40 [RX MOD]

42 [S SRCH]

49 [STEP]

51 [TOT]

52 [TX.LED]

54 [VFO.BND]

55 [WID.NAR]

OFF / 0.5H - 12.0 H

BCL. ON / BCL.OFF

LED. ON / LED.OFF

SFT.OFF / SFT. ON

–

INT. 1M - INT. 50M /

ON. 1M - CON.50M / OFF

BEP.OFF / BEP. ON

EMG.BEP / EMG.LMP / EMG.B+L /

EMG.CWT / EMG.C+B /

EMG.C+L / EMG.ALL / OFF

PWD.OFF / PWD. ON

–

S-1 / S-2 / S-3 / S-4 / S-5 / S-6 /

S-8 / S-FULL / OFF

AUTO / FM / AM

SINGLE / CONT

5 / 10 /12.5 / 15 / 20 / 25 /

50 / 100 kHz, or AUTO

1MIN - 30MIN or OFF (6MIN)

LED. ON / LED.OFF

BAND / ALL

WIDE / NARROW

FT-60R OPERATING MANUAL

SET (MENU) MODE

Set Mode Item 1 [APO]

Function: Setting of the Automatic Power-Off feature.

Available Values: OFF/0.5H - 12.0 H in 0.5 hour multiples

Default: OFF

Set Mode Item 2 [AR BEP]

Function: Selects the Beep option during ARTS operation.

Available Values: INRANG/ALWAYS/OFF

Default: INRANG

INRANG: Beeps sound only when the radio first detects that you are within range.

ALWAYS: Beeps sound every time a polling transmission is received from the other sta

tion (every 15 or 25 seconds when in range).

OFF: No alert beeps sound.

Set Mode Item 3 [AR INT]

Function: Selects the Polling Interval during ARTS operation.

Available Values: 25 SEC/15 SEC

Default: 25SEC

Set Mode Item 4 [ARS]

Function: Enables/Disables the Automatic Repeater Shift function.

Available Values: ARS. ON/ARS.OFF

Default: ARS. ON

Set Mode Item 5 [BCLO]

Function: Enables/Disables the Busy Channel Lock-Out feature.

Available Values: BCL. ON/BCL.OFF

Default: BCL.OFF

Set Mode Item 6 [BEEP]

Function: Enables/Disables the beeper.

Available Values: KEY+SC/KEY/OFF

Default: KEY+SC

KEY+SC: The beeper sounds when you press any key, or when the scanner stops.

KEY: The beeper sounds when you press any key.

OFF: Beeper is disabled.

Set Mode Item 7 [BELL]

Function: Selects the number of CTCSS/DCS Bell ringer repetitions.

Available Values: OFF/1T/3T/5T/8T/CONT (Continuous ringing)

Default: OFF

FT-60R OPERATING MANUAL

SET (MENU) MODE

Set Mode Item 8 [BSY.LED]

Function: Enables/Disables the BUSY LED while the Squelch is open.

Available Values: LED. ON/LED.OFF

Default: LED. ON

Set Mode Item 9 [CLK.SFT]

Function: Shifting of the CPU clock frequency.

Available Values: SFT.OFF/SFT. ON

Default: SFT.OFF

This function is only used to move a spurious response “birdie,” should it fall on a desired

frequency.

Set Mode Item 10 [CWID]

Function: Enables/disables the CW identifier during ARTS operation.

Available Values: TX OFF/TX ON

Default: TX OFF

Set Mode Item 11 [CW WRT]

Function: Programs and activates the CW Identifier (used during ARTS operation).

See page 53 for details.

Set Mode Item 12 [DC VLT]

Function: Indicates the DC Supply Voltage.

Set Mode Item 13 [DCS.COD]

Function: Setting of the DCS code.

Available Values: 104 standard DCS codes

Default: DCS.023

Set Mode Item 14 [DCS.N/R]

Function: Enables/Disables “Inverted” DCS

code decoding.

Available Values: T/RX N, RX R, TX R,

T/RX R

Default: T/RX N

DCS CODE

023 025 026 031 032 036 043 047 051 053

054 065 071 072 073 074 114 115 116 122

125 131 132 134 143 145 152 155 156 162

165 172 174 205 212 223 225 226 243 244

245 246 251 252 255 261 263 265 266 271

274 306 311 315 325 331 332 343 346 351

356 364 365 371 411 412 413 423 431 432

445 446 452 454 455 462 464 465 466 503

506 516 523 526 532 546 565 606 612 624

627 631 632 654 662 664 703 712 723 731

732 734 743 754 – – – – – –

Set Mode Item 15 [DT DLY]

Function: Setting of the DTMF Autodialer Delay Time.

Available Values: 50MS/100MS/250MS/450MS750MS/1000MS

Default: 450MS

Set Mode Item 16 [DT SPD]

Function: Setting of the DTMF Autodialer Sending Speed.

Available Values: 50MS (high speed)/100MS (low speed)

Default: 50MS

FT-60R OPERATING MANUAL

SET (MENU) MODE

Set Mode Item 17 [DT WRT]

Function: Programming of the DTMF Autodialer.

See page 54 for details.

Set Mode Item 18 [EAI]

Function: Enables/Disables the Emergency Automatic ID (EAI) Feature.

Available Values:

INT. 1M - INT.10M, INT.15M, INT.20M, INT.30M, INT.40M, INT. 50M,

CON. 1M - CON.10M, CON.15M, CON.20M, CON.30M, CON.40M, CON. 50M, and

OFF

Default: OFF

Set Mode Item 19 [EDG.BEP]

Function: Enables/Disables the Band-edge beeper while selecting the frequency via the

DIAL knob.

Available Values: BEP.OFF/ BEP. ON

Default: BEP.OFF

Set Mode Item 20 [EMG S]

Function: Selects the alarm(s) utilized when the Emergency function is engaged.

Available Values: EMG.BEP/EMG.LMP/EMG.B+L/EMG.CWT/EMG.C+B/EMG.C+L/

EMG.ALL/OFF

Default: EMG.B+L

EMG.BEP: Loud “Alarm” sounds.

EMG.LMP: The LCD/Keypad lamp flashes.

EMG.B+L: Loud “Alarm” sounds and the LCD/Keypad lamp flashes.

EMG.CWT: Transmits the Morse Code “SOS” (••• – – –•••) message on the air beginning

one minute after activation of the Emergency function.

EMG.C+B: Loud “Alarm” sounds and the Morse Code “SOS” (••• – – –•••) message is

transmitted on the air beginning one minute after activation of the Emergency

function.

EMG.C+L: The LCD/Keypad lamp flashes, and the Morse Code “SOS” (••• – – –•••)

message is transmitted on the air beginning one minute after activation of the

Emergency function.

EMG.ALL: All of the above are activated.

OFF: Disables the Emergency function. The Emergency function also cannot be

engaged, by pressing and holding in the [4(RPT)] key, if this Menu is set to

“OFF.”

When the radio is set to the EMG.CWT, EMG.C+B, EMG.C+L, or EMG.ALL mode, the

radio will be instructed to send “DE (your callsign)” after the sending of the SOS message,

if your callsign is entered via Set Mode Item 10: CWID.

FT-60R OPERATING MANUAL

SET (MENU) MODE

Set Mode Item 21 [I NET]

Function: Selects the Internet Link Connection mode.

Available Values: INT.OFF/INT.COD/INT.MEM

Default: INT.OFF

INT.OFF: Disables the Internet Link Connection mode.

INT.COD: Sets up the Internet Link Connection mode for WIRES™ access.

INT.MEM: Sets up the Internet Link Connection mode for other (DTMF string) Internet

Link System access.

Set Mode Item 22 [INT CD]

Function: Selects the Access Number (DTMF digit) for WIRESTM operation.

Available Values: CODE 0 - CODE 9

Default: CODE 1

Set Mode Item 23 [INT MR]

Function: Selects the memory register for an Access Number (DTMF code) for non-

WIRES™ Internet Link System access.

Available Values: d1 - d9

Default: d1

Set Mode Item 24 [LAMP]

Function: Selects the LCD/Keypad Lamp mode.

Available Values: KEY/5SEC/TOGGLE

Default: KEY

KEY: Illuminates the Keypad/LCD for five seconds when you rotate the DIAL knob

or press any key or switch (except the PTT switch).

5SEC: Illuminates the Keypad/LCD for five seconds when you press the LAMP switch

momentarily.

TOGGLE: Toggles the Keypad/LCD lamp on and off when you press the LAMP switch

repeatedly.

Set Mode Item 25 [LOCK]

Function: Selects the Control Locking lockout combination.

Available Values: LK KEY/LKDIAL/LK K+D/LK PTT/LK P+K/LK P+D/LK ALL

Default: LK KEY

Note: “K” = “Key;” “D” = “Dial;” and “P” = “PTT.”

FT-60R OPERATING MANUAL

SET (MENU) MODE

Set Mode Item 26 [M/T-CL]

Function: Selects the MONI key (just below the PTT switch) function.

Available Values: MONI/T-CALL

Default: Depends on the transceiver version.

MONI: Pressing the MONI key causes the Noise/Tone Squelch to be over-ridden, allow

ing you to listen for weak (or non-encoded) signals.

T-CALL: Pressing the MONI key activates a 1750-Hz burst tone, used for repeater access

in many countries (especially in Europe).

Set Mode Item 27 [NAME]

Function: Toggles the display indication between “frequency” and the channel’s “Alpha/

Numeric Tag.”

Available Values: FREQ/ALPHA

Default: FREQ

Set Mode Item 28 [NM WRT]

Function: Stores Alpha-Numeric “Tags” for the Memory channels.

See page 30 for details.

Set Mode Item 29 [PAGER]

Function: Enables/disables the Enhanced CTCSS Paging & Code Squelch function.

Available Values: OFF/ON

Default: OFF

Set Mode Item 30 [PAG.ABK]

Function: Enables/disables the Answer Back function of the Enhanced CTCSS Paging &

Code Squelch.

Available Values: ABK.OFF/ABK. ON

Default: ABK.OFF

Set Mode Item 31 [PAG.CDR]

Function: Setting the Receiver Pager Code for the Enhanced CTCSS Paging & Code

Squelch.

See page 44 for details.

Set Mode Item 32 [PAG.CDT]

Function: Setting the Transmitting Pager Code for the Enhanced CTCSS Paging & Code

Squelch.

See page 44 for details.

Set Mode Item 33 [PSWD]

Function: Enables/disables the Password feature.

Available Values: PWD.OFF/PWD. ON

Default: PWD.OFF

FT-60R OPERATING MANUAL

SET (MENU) MODE

Set Mode Item 34 [PSWD W]

Function: Stores the password.

Available entries are 0-9, A, B, C, D, E (substitute for “.”), and F (substitute for “#”)

Set Mode Item 35 [RESUME]

Function: Selects the Scan Resume mode.

Available Values: BUSY/HOLD/TIME

Default: BUSY

BUSY:

The scanner will hold until the signal disappears, then will resume when the carrier

drops.

HOLD: The scanner will stop when a signal is received, and will not restart.

TIME:

The scanner will hold for the five seconds, then resume whether or not the other

station is still transmitting.

Set Mode Item 36 [REV/HM]

Function: Selects the function of the [HM/RV] key.

Available Values: <REV> / <HOME>

Default: <REV>

<REV>:

Pressing the [HM/RV] key reverses the transmit and receive frequencies during

repeater operation.

<HOME>: Pressing the [HM/RV] key instantly recalls a favorite “Home” channel.

Set Mode Item 37 [RF SQL]

Function: Adjusts the RF Squelch threshold level.

Available Values: S-1/S-2/S-3/S-4/S-5/S-6/S-8/S-FULL/OFF

Default: OFF

Set Mode Item 38 [RPT.MOD]

Function: Sets the Repeater Shift Direction.

Available Values: RPT.OFF/RPT. -/RPT. +

Default: Depends on the transceiver version, as well as the setting of Set Mode Item 4:

ARS.

Set Mode Item 39 [PRI.RVT]

Function: Enables/disables the Priority Revert feature.

Available Values: RVT.OFF/RVT. ON

Default: RVT.OFF

See page 42 for details.

Set Mode Item 40 [RX MOD]

Function: Selects the receiving mode.

Available Values: AUTO/FM/AM

Default: AUTO (Mode automatically changes according to operating frequency)

FT-60R OPERATING MANUAL

SET (MENU) MODE

Set Mode Item 41 [RXSAVE]

Function: Selects the Receive-mode Battery Saver interval (“sleep” ratio)

Available Values: 200 MS(1:1)/300 MS(1:1.5)/500 MS(1:2.5)/1 S(1:5)/2 S(1:10)/OFF

Default: 200 MS

Set Mode Item 42 [S SRCH]

Function: Selects the Smart Search Sweep mode.

Available Values: SINGLE/CONT

Default: SINGLE

SINGLE: The transceiver sweeps the current band once in each direction, starting on the

current frequency. All channels where activity is present (up to 15 in each direction)

are loaded into the Smart Search memories. Whether or not all 31 memories

are filled, the search stops after one sweep in each direction.

CONT:

The transceiver makes a sweep in each direction as with the “SINGLE” mode,

but if all 31 channels are not filled after the first sweep, the radio continues

sweeping until they are all filled.

Set Mode Item 43 [SCN MD]

Function: Selects the Memory Scan channel-selection mode.

Available Values: ONLY/MEM

Default: MEM

ONLY: The scanner will only scan channels that are flagged (Preferential Scan List).

MEM: The scanner will “skip” the flagged channels during scanning.

Set Mode Item 44 [SCN.LMP]

Function: Enables/Disables the Scan lamp while paused.

Available Values: ON/OFF

Default: ON

Set Mode Item 45 [SHIFT]

Function: Sets the magnitude of the repeater Shift.

Available Values: 0.00 - 99.95 MHz (50 kHz increments)

Default: Depends on the operating band and transceiver version.

Set Mode Item 46 [SKIP]

Function: Selects the Memory Scan “Skip” channel-selection mode.

Available Values: OFF/SKIP/ONLY

Default: OFF

SKIP: The scanner will “skip” the flagged channels during scanning.

ONLY: The scanner will only scan channels that are flagged (Preferential Scan List).

OFF: All memory channels will be scanned (the “flag” will be ignored).

FT-60R OPERATING MANUAL

SET (MENU) MODE

Set Mode Item 47 [SPLIT]

Function: Enables/Disables split CTCSS/DCS coding.

Available Values: SPL.OFF/SPL. ON

Default: SPL.OFF

When this Set Mode Item is set to “SPL. ON,” you will see the following additional parameters

after the “DCS” parameter while configuring Set Mode Item 47: SQL.TYP.

D: DCS Encode only.

T DCS: Encodes a CTCSS tone and Decodes a DCS code.

D TSQL: Encodes a DCS code and Decodes a CTCSS tone.

Select the desired operating mode from the selections shown above.

Set Mode Item 48 [SQL.TYP]

Function: Selects the Tone Encoder and/or Decoder mode.

Available Values: OFF/TONE/TSQL/REV TN/DCS

Default: OFF

TONE: CTCSS Encoder

TSQL: CTCSS Encoder/Decoder

REV TN: Reverse CTCSS Decoder (Mutes receiver when matching tone is received)

DCS: Digital Coded Encoder/Decoder

Note: See also Set Mode Item 46: SPLIT regarding additional selections available during

“Split Tone” operation.

Set Mode Item 49 [STEP]

Function: Setting of the synthesizer steps.

Available Values: 5/10/12.5/15/20/25/50/100 kHz, or AUTO

Default: AUTO (Step automatically changes according to operating frequency.)

Set Mode Item 50 [TN FRQ]

Function: Setting of the CTCSS Tone Frequency.

Available Values: 50 standard CTCSS tones

Default: 100.0 Hz

Set Mode Item 51 [TOT]

Function: Setting of the TOT time

Available Values: 1MIN - 30MIN or OFF

Default: 6MIN (minutes)

The time-out timer shuts off the transmitter after continuous transmission of the programmed

time.

CTCSS TONE FREQUENCY (Hz)

67.0 69.3 71.9 74.4 77.0 79.7

82.5 85.4 88.5 91.5 94.8 97.4

100.0 103.5 107.2 110.9 114.8 118.8

123.0 127.3 131.8 136.5 141.3 146.2

151.4 156.7 159.8 162.2 165.5 167.9

171.3 173.8 177.3 179.9 183.5 186.2

189.9 192.8 196.6 199.5 203.5 206.5

210.7 218.1 225.7 229.1 233.6 241.8

250.3 254.1 – – – –

FT-60R OPERATING MANUAL

SET (MENU) MODE

Set Mode Item 52 [TX.LED]

Function: Enables/Disables the TX LED while the radio is transmitting.

Available Values: LED. ON/LED.OFF

Default: LED. ON

Set Mode Item 53 [TXSAVE]

Function: Enables/Disables the Transmitter Battery Saver.

Available Values: SAV.OFF/ SAV. ON

Default: SAV.OFF

Set Mode Item 54 [VFO.BND]

Function: Enables or disables the VFO band edge limiting for the current band.

Available Values: BAND/ALL

Default: BAND

BAND: When the VFO frequency reaches the high band edge of the current band, the

VFO frequency will jump to the low band edge of the current band (or vice versa).

ALL: When the VFO frequency reaches the high edge of the current band, the VFO

frequency will jump to the low band edge of the next band (or vice versa).

Set Mode Item 55 [WID.NAR]

Function: Select Wide (±5 kHz) or Narrow (±2.5 kHz) TX Deviation.

Available Values: WIDE/NARROW

Default: WIDE

Note: If “Narrow” is selected, the receiver audio level is increased slightly to compensate

for the reduced deviation. The receiver IF filter bandwidth is not changed via this setting.

Set Mode Item 56 [WX ALT]

Function: Enables/Disables the Weather Alert Scan feature.

Available Values: ALT.OFF/ALT. ON

Default: ALT. OFF

FT-60R OPERATING MANUAL

SPECIFICATIONS

General

Frequency Ranges: RX 108 - 137 MHz (Air Band),

(Cellular Blocked) 137 - 520 MHz (AM/FM),

700 - 999.990 MHz (FM)

TX 144-148 MHz, 430-450 MHz

Channel Steps: 5/10/12.5/15/20/25/50/100 kHz

Frequency Stability: ±5 ppm @ 14 ºF to 122 ºF (–10 °C to +50 °C)

Repeater Shift: ±600 kHz (144 MHz), ±1.6/5.0/7.6 MHz (430 MHz)

Emission Type: F2D, F3E

Antenna Impedance: 50 .

Supply Voltage: Nominal: 7.2 V DC, Negative Ground

(Negative Ground) Operating:6.0 ~ 16.0 V DC (EXT DC Jack)

11.0 ~ 16.0 V DC (EXT DC Jack with Charging)

Current Consumption: 125 mA (Receive)

(Approx. @7.2 V) 45 mA (144 MHz, Standby, Saver Off)

47 mA (430 MHz, Standby, Saver Off)

19 mA (Standby, Saver On)

0.8 mA (Auto Power Off)

1.3 A (5 W TX, 144 MHz)

1.5 A (5 W TX, 430 MHz)

Operating Temperature: –4 ºF to 140 ºF (–20 °C to +60 °C)

Case Size: 2.3” (W) x 4.3” (H) x 1.2” (D) (58 x 109 x 30 mm)

(W/O knob, antenna, and belt clip)

Weight: 13.05 Oz (370 g) with FNB-83, and antenna

Transmitter

RF Power Output: 5.0 W (High) / 2.0 W (Middle) / 0.5 W (Low) (Approx.)

Modulation Type: Variable Reactance F2D, F3E

Maximum Deviation: ±5.0 kHz (F2D, F3E)

Spurious Emission: At least 60 dB down (@ High and Middle power)

At least 40 dB down (@ Low power)

Microphone Impedance:2 k.

Receiver

Circuit Type: Double-Conversion Superheterodyne

Intermediate Frequencies: 1st: 47.25 MHz, 2nd: 450 kHz

Sensitivity : 0.8 µV TYP for 10 dB SN (108-137 MHz, AM)

(Cellular Blocked) 0.2 µV for 12 dB SINAD (137-140 MHz, FM)

0.16 µV for 12 dB SINAD (140-150 MHz, FM)

0.2 µV for 12 dB SINAD (150-174 MHz, FM)

0.3 µV TYP for 12 dB SINAD (174-300 MHz, FM)

0.8 µV for 10 dB SN (300-336 MHz, AM)

0.25 µV for 12 dB SINAD (336-420 MHz, FM)

0.2 µV for 12 dB SINAD (400-470 MHz, FM)

0.25 µV for 12 dB SINAD (470-520 MHz, FM)

0.5 µV TYP for 12 dB SINAD (800-900 MHz, FM)

0.8 µV TYP for 12 dB SINAD (800-999.990 MHz, FM)

Selectivity: 12 kHz/35 kHz (–6 dB /–60 dB)

AF Output: 400 mW @ 8 Wfor 10 % THD (@ 7.5 V)

Specifications are subject to change without notice, and are guaranteed within the 144 and 430

MHz amateur bands only. Frequency ranges will vary according to transceiver version; check

with your dealer.

FT-60R OPERATING MANUAL

“AUTO” MODE PRESET OPERATING PARAMETERS

FREQENCY RANGE

(MHZ)

108.000 - 137.000

137.000 - 144.000

144.000 - 148.000

148.000 - 156.000

156.000 - 157.450

157.450 - 160.600

160.600 - 160.975

160.975 - 161.500

161.500 - 162.900

162.900 - 174.000

MODE

STEP

25 kHz

12.5 kHz

5 kHz

12.5 kHz

25 kHz

12.5 kHz

25 kHz

12.5 kHz

25 kHz

12.5 kHz

FREQENCY RANGE

(MHZ)

174.000 - 222.000

222.000 - 225.000

225.000 - 300.000

300.000 - 336.000

336.000 - 420.000

420.000 - 450.000

450.000 - 470.000

470.000 - 520.000

700.000 - 800.000

800.000 - 999.990

MODE

STEP

50 kHz

5 kHz

12.5 kHz

100 kHz

12.5 kHz

25 kHz

12.5 kHz

50 kHz

12.5 kHz

FT-60R OPERATING MANUAL

Changes or modifications to this device not expressly approved by VERTEX

STANDARD could void the user’s authorization to operate this device.

This device complies with part 15 of the FCC Rules. Operation is subject to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference including

received, interference that may cause undesired operation.

3. The scanning receiver in this equipment is incapable of tuning, or readily

being altered, by the User to operate within the frequency bands allocated

to the Domestic public Cellular Telecommunications Service in Part 22.

DECLARATION BY MANUFACTURER

The Scanner receiver is not a digital scanner and is incapable of being converted

or modified to a digital scanner receiver by any user.

WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR

RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES

AND FEDERAL LAW.

VERTEX STANDARD CO., LTD.

No portion of this manual

may be reproduced

without the permission of EH017M100

VERTEX STANDARD CO., LTD. 0406x-0X

Disclaimer: The information on this site is provided as a public service to the blind and visually handicapped community. While we have done our best to ensure the information provided is accurate, please realize the use of any information on this site is solely at your discretion and we take no responsibility for use or attempted use of this information.