SuperAntennas MP1 HF Antenna Info.
>
> Portable HF Antenna Review From A Blind Hams Perspective.
>
> December 3, 2010, Toccoa, GA.
>
> From Danny Dyer, Wb4idu.
>
> I've not had time until this evening to search through my pack rat email file to find these notes, which I'd sent last january, to both the developer of
> the MP1, and to the moderator of its' email list for comment and corection.
>
> Both Vern and Virgil were very helpful, and wasted no time in getting back to me.
>
> It's taken me too long to edit, update, and finalize this, but I hope it may help someone.
>
> I'm posting this to the blind hams lists, to handihams and to Icanworkthisthing.com,
>
> in hopes of introducing more folks to one of the finest and most useable products around.
>
> Thanks to all, for all you are and all you do. Danny.
>
> *Text*
>
> "InMay of 2008, the following note appeared on one of the internet lists
> frequented by Blind Ham Radio Operators.
> which said in part,
> "Can anyone give me some suggestions for purchasing an auto antenna tuner
> that is accessible? ....
> I only plan to use it with 200 watts or less. Also, I would like to do some
> portable HF work. I am not looking to mount the antenna on a car. I am
> planning to use some type of tripod mount such as a roof tripod. I want
> something that I can take to people's houses when I visit or camping. I
> would like some suggestions on antennas that will work 10 through 80 meters
> that I wouldn't need to run a lot of wire with. Thanks for the help."
>
> In early January of 2010, came these questions&observations from another blind ham on list.
>
> "I'm trying to find something that is 6 feet tall or less, that will play on
> at least 40M and up, and that won't break the bank...IE, less than $200....
>
> I can deploy an antenna on a somewhat permanent basses on the balcony, ...I can run counterpoise/ground radials along bassboards, and possibly smaller
> radials
> outside, or use the railing for a counterpoise system...
> during the winter months, I have to bring the antenna in because I can't run coax cables out the balcony door as the cold air coming through the
> crack can freeze hot water heating pipes directly below the doors....
>
> As a last resort, i could go mobile and mount on the car and play HF in the
> mobile, but I would prefer something in the house."
>
> Well since I'm a lifetime blind, longtime ham who's
> experimented a bit with both, portable antennae, and "mobile antennae
> operating as portable antennae,"
> both with and without tuners;
> I thought I'd chime in, with my observations/your mileage may varry, as to
> which antenna, other than longwires, dipoles, and such, I've found to be,/
> Not necessarily in this order:
> 1, simplest to deploy,
> 2, cheapest to obtain,
> And, 3, most efficient for tuning and use by both
> blind and sighted hams, wishing to
> A, run 200Watts or less,
> B, on 80-10meters,
> C, in fixed and or or portable configurations,
> D, either with or without a separate tuner.
> And while I regret not completing and posting these observations before now;
> It seems to me that in light of A, continuing marginal band conditions,
> B, increased interest in many aspects of our Amateur Radio Service, and
> C, increased financial and logistical challenges experienced by sighted and
> blind amateurs alike,over the past couple of years, these findings may prove
> to be even more valuable now than they would have been then:
> ***for either a sighted or blind ham, Other than typical wire antennas, the
> most accessible, easiest to deploy,
> simplest to use, and easiest to tune, portable HF antenna I've successfully
> used,owned, sold, swapped, and keep coming back to, is the Super Antennas
> MP1, Antenna system, made and marketed by
>
> VERNON L WRIGHT,/Vern, W6MMA,
>
> Phone: 916-434-9936
>
> Email,
> w6mma@wavecable.com
>
> (****Important Note,
>
> Due To Litigation, Use Only The Above Contact Information.)
>
> The antenna was rated _very highly in real world, Independently Supervised
> Ham Radio testing, recorded in the "antenna Shoot Out, as listed in the
> archives of the files section of the HFPack Yahoo Group;
> I know of at least One Other Blind Ham,
>
> (Jack McSpadden/Wa5ROP in Little Rock, AR, USA, )who,, for a number of years, has successfully used this arrangement in several venues,
> including on a cruze ship;
>
> And I know of several sighted hams,
>
> who swear by, rather than swearing at, the MP1 Systems:
>
> *Notes, 1, These observations/instructions ar derived from having talked with and having read comments from a number of users, and from my own experience
> with a number of these systems over the past six or seven years.
>
> 2, I've noticed a lot of questions re different facits of operation, and have asked a number of them myself.
>
> 3, Anyone is more than welcome to use and hopefully benefit from any and all that's written here.
>
> 4, I am not an official spokes person for Vern, the Company, or anyone else except myself, and nothing I've written here is copywrited.
>
> This is what's known as a
>
> "manual screw driver antenna,
>
> whereby a sliding sleeve is positioned /moved by hand, along a coil to help to tune or match the whip antenna to a large number of desired transmitting
> and receiving frequencies."
>
> *2, (all connecting "threaded stubs and holes" are 3/8by24, which is pretty standard when it comes to this type of antenna.)
>
> *3, , Because of above mentioned litigation, availability of some systems and or parts may be limited, check with dealers, ham websites, and of course with
> Vern himself.
>
> Hopefully all issues will soon be successfully litigated
>
> Details.
>
> The basic system sells for $99&Change, and consists of,
> 1, a basic, (40-10meter coil, with sliding sleeve, having a hole in its' bottom , {for atatchment of either a
>
> 2, 2Foot Base Rod Or 80meter coil;])
>
> as well as having a
> Hole@its'
> Topp,
>
> (For atatchment of the
>
> 3, whip antenna;)
>
> and
>
> finally, a nylon thum bscrew on its' side, about an inch from the bottom, /{to help the operator to both noncapacitively, by hand, tune the sleeve to the
> optimum position on the coil, and then to help steady it there, }*Although that thumbscrew should only be slightly tightened,/more about that later:)
>
> The basic coils' metal sleeve, is somewhat shorter than the coil itself,
> and When Slidden all the way down over it,/
> (10Meter Position,)Covers all the coil's windings,when slidden all the way up/(40Meter Position, )
>
> exposes the coil's windings.
>
> *The 80meter coil typically always has all of its' windings exposed.
>
> [The basic coil and sleeve are made so that in most instances,
>
> once its' desired position on the basic coil is reached,
>
> the sleeve, even with the atatched whip, will stay in place.
>
> But the Thumb Screw can be employed/Tightened _Slightly,
>
> to reenforce the stability of the setting.])}
>
> (3, 4foot, 12Section, telescoping antenna,
> With Threaded
> Stub@Bottom
> ;
> 4, 2foot metal base Rod/(Made Up Of 2, 1foot Sections
>
> ,with threaded ends connected through a hexnut./
>
> (Each base rod section, comes with a corresponding nut to go on each
> end, with a "Hex Nut" to connect the rod sections/using the lil nuts to "set
> the rod sections to suit the operator's fancy);
> 5, Universal Mounting Bracket &CClamp,/(bracket is 3pieces of same width and thickness metal, all with rounded ends/(A, a flat aprox 9x2x1Fourth IN rectangle,
> connected by screw&washer, to,
>
> B, right angle,with Aprox2IN and 1IN sides,
>
> Connected by Screw&Washer to,
>
> C, Similarly sized Right Angled piece with Female Coax To Female 3/8by24Thread
>
> antenna adapter.
>
> {These pieces can be angled differently to work with Verticle, Horizontal, and sloped surfaces};
>
> 6, Counterpoise system,/
>
> Four roughly 13 foot lengths of 3Conductor RibbonCable,With all wires atatched to washer type spade lug connecter;
> 7, paper work simple instruction sheet;
> 8, shipping box:
> ~~~Additional items are available which include,
> A, 80meter coil, (Somewhat shorter than basic coil,
> Has Threaded stub on top,threaded hole in bottom,
> {Designed to fit between lower rod and basic coil /with basic coil's sleeve extendded all the way out, for 80meter operation,}
> [Or To be _the _only coil/using no other coil or sliding sleeve, ,/between Lower Rod And Antenna,for sixty meter
> operation,]
> (For Sixty Meters, connect the stub on coil to stub on antenna with an extra
> hex nut/not supplied,
> And Connect bottom of coil to Base Rod as usual,
>
> then use a 32-42Foot Counterpoise);
> B, tripod,(3, matching, Metal Legs,/
>
> usually 8 or so inches long,
>
> With Plastic Tips on 1 end,
>
> and threads on the other, that atatch to
>
> round CoaxToThreadedAntennaAdapter;
> C, "Rig Mounted Side Bracket"(My Description,)/
>
> (Single flat piece of metal, Maybe 1EighthInch Thick,
>
> slightly narrower and about2Inches longer than rig,
>
> has rounded end, with screw hole for nut&Bolt to connect to Same type right angled
>
> CoaxToThreaded ant adapter as on Universal Bracket,/Also comes with Coax Male To Female Elbow To Increase Useability.
>
> {Comes With 4Screws, same diameter and thread, but longer than OEM./
>
> {The Bracket mounts firmly on side of rig,
>
> allowing antenna to be mounted at,
>
> 1, a 90degree angle,
> for picnic table portable, indoor, or other operation, .
> 2, parallel to side of rig for pedestrien portable, or
> 3, anywhere inbetween for other applications,/
>
> [the nut and bolt on the side mount bracket
>
> can be loosened and or tightened, to determine the antenna's position relative to the radio}](Designed to work with
> Icom IC703, 706, and possibly other Icom Models,
> Yaesu FT817, 857, and 897 series,
> And Any Other Radio With Similar case configurations;
>
> *At last check, prices for
>
> A, B, And C, Are Vicinity Of $32Each.)
>
> D, 4Foot Base Rod,/
>
> 2,2foot sections connected by hexnut;
>
> E, 4Foot Solid Stainless Steel Whip;
>
> (D, and E, Sold together as "Mobile Kit,
>
> *At last check Mobile Kit Was available for 20To40$s.)
>
> *Explanation, and installation instructions.
>
> ~~~~
>
> *Note!
>
> ***Warning, To Avoid Damage To The System,
>
> _Please Heed And Follow These Instructions.
>
> 1, Both the basic/40-10meter coil, (which has a sliding metal sleeve around it,
>
> and the 80meter coil, which does not,
>
> although stirdy, _Are Not_ Indestructible!
>
> *The sliding sleeve has a small hole,
>
> About an inch above its' bottom,
>
> Into which a
>
> small nylon nonconductive thumb screw is inserted.
>
> The purpose of the thumb screw is to help to hold
>
> the sleeve with whip antenna atatched,
>
> at the desired position along the basic coil.
>
> ***Before you go any further,
>
> *1, turn the thumb screw counter clockwise,
>
> Until it disengages from the sleeve.
>
> 2, slide the sleeve off of the coil.
>
> 3, Place your index finger about an inch above
>
> the bottom of the inside of the sleeve,
>
> 4, turn the sleeve until your finger touches the hole in it,
>
> 5, Reinsert the thumb screw into the hole,
>
> 6, gently turn the thumb screw clockwise,
>
> until it barely touches your finger.
>
> 7, then turn the thumb screw clockwise,
>
> with your finger still touching it,
>
> and note the pressure/don't hurt yourself,
>
> But realize that the screw can,
>
> both hurt your finger,
>
> and permanently damage your coil.
>
> *So use its' pressure
>
> ___Sparingly!
>
> 8, try this several times so that you have an understanding
>
> of how much or more accurately how little,
>
> head room you have in adjusting that thumb screw,
>
> between no pressure against the finger or coil,
>
> , and too much pressure against the finger or coil.
>
> 9, position the thumb screw in the sleeve,
>
> so that it barely touches your finger,
>
> then slide the sleeve back onto,
>
> then all the way down the coil.~~~
>
> *Now for the fun stuff.
>
> ***This Explanation/set of instructions,presumes your use of 1,"Universal bracket,
> 2, Basic Coil,and sleeve,
> 3, shorter lower rod,
> 4, telescoping antenna,
> but are pretty much the same if using
> A,one of the other brackets/tripod/or an existing magmount,,
> B, added coil,or only 80meter coil,
> C, longer lower rod,
> D, solid antenna, etc.
> In essence, this is a "manual screwdriver" arrangement, whereby
> Basically, you,
>
> Step1, atatch the Universal Mount to a table, railing, windowledge, or other mettalic or non mettalic
> surface via the C Clamp;
>
> Step2, Connect counterpoise wires to the universal mount, and extend them.
>
> (Note1,both brackets and the tripod have an
>
> atatched-by-screw, Spade Lug Peg,
>
> For Easy Connect and Disconnect of Counterpoise)
>
> {Note2,other types and lengths of counterpoises, IE, EG, varying single lengths of insulated wire,
>
> cut to more or less each band,
>
> or one long single insulated wire,
>
> long enough for 80meters,
>
> but with knot, or tape markers at other band lengths, are also being used};
>
> 3, connect the 2 "lower rod" sections together, through the supplied hex nut, via their corresponding
> 3/8sby24 threads;
> 4,Atatch that lower rod, into the universal bracket, using the threaded end of the coax-to-Antenna adapter, via their corresponding threads;
>
> *Note,(Instructions are the same if using one of the other brackets or the
> tripod.)
> 5, plug in your coax jumper to the Coax plug/usually on the under side of the antenna to coax adapter;
>
> 6, plug the other end of your coax jumper into the HF Coax Socket on your radio;
>
> 7, Mount the coil toThe upper end of the Lower Rod,
>
> via their corresponding threads,
>
> *for 40-10meters, simply mount the basic coil,
>
> *for 80meters, mount the 80meter coil first/,
>
> then the basic coil on top of it,
>
> *For 60meters, Mount _Only The 80Meter Coil;
>
> 8, Mount the antenna, Into the sleavetop via their corresponding threads,
>
> *For 60Meters, Atatch the top of the 80meter coil
>
> which you've already atatched to the lower rod,
>
> to the bottom of the antenna,
>
> through an additional hex nut, _not supplied;.
> 9, fully extend the telescopic antenna;
>
> 10, tune the desired frequency between 40 and 10 meters on your tranceiver.
>
> 11, Using the nonconductive thumbscrew on the bottom of the sleeve,/(I find it best for me to hold it between thumb and first two fingers, but experiment
> and find your own best position,)
>
> slowly slide the sleeve up and down the basic coil, until highest/loudest signal to noise ratio is reached;
>
> 12, when one reaches the best /loudest, signal to noise ratio on that desired frequency, you're very close to best/lowest, SWR, and best /highest efficiency
> setting for successful HF Transmitting:
>
> 13, *Note, (Handd Capacitence Coupling,
>
> while working with the "slider/sleeve, as you move it up and down the coil, you will notice that the touch and or even proximity of your hand,
>
> may somewhat change the capacitence of the system./(after tuning for max signal, Removing your hand may slightly bring up/increase, or bring down/decrease,
> )the amount or level of the received/heard signal, {depending on which side of the Maximum natching position of the sleeve on the coil you've tuned;}
>
> and thereby somewhat change the swr and "matchedness" level of the system:
>
> Using the Thumb Screw properly, will negate most if not all of this,
>
> and You'll learn to properly evaluate and or compensate for this as you go along.
>
> But you may also wish to slip a rubber, or other noncapacitive type of
> "ring: around the sliding sleeve to negate it even more; so that you can grasp it _without any noticeable "hand capacitence coupling, thereby simplifying
> and improving your tuning accuracy):
>
> 14, after successfully completing steps 1-12,
>
> and giving due consideration to #13,
>
> you may wish to establish, confirm, and check
>
> the accurate tuning /matching of this antenna system
>
> to your tranceiver, by use of an additional
>
> tuner, and or swr meter, and or Watt Meter.
>
> Any or All of These instruments will prove helpful to you,
>
> as you tweek/fine tune the system,
>
> And as you practice, you'll likely find that you can
>
> Successfully And Accurately Match,
>
> this antenna system to virtually any HF tranceiver
>
> on any band, 80meters through 10meters,
>
> By Simple Steady, hand and ear coordination,
>
> without using anything more than Simply, the antenna and the tranceiver:
>
> ^^^Notes, A, All measurements are approximate, but to the best of my remembrance, accurate.
> B, I've successfully used this antenna with Basic Bracket, Tripod, and Side Mount Bracket.
>
> (When using side mount bracket, most users recommend staying at or under the transmitters' 5Watt Power Output, for rf safety reasons.)
>
> C, For The Record,
>
> *I have no connection with any company mentioned;
> *I am not receiving any remuneration for these thoughts;
> *They're shared by a pleasantly satisfied,
>
> User-Customer-Recommender
> of The Super Antennas MP1 Portable Antenna System;
> D,*,There is at least one antenna system out there, notably the Blue Star antenna System,/
>
> which, 1, I understand is somewhat similar,
>
> 2, unfortunately, I've never had my hands on,
> 3, I understand is more expensive,
>
> *I have no experience with
>
> other manual screwdriver antennae:
>
> These however, are my observations regarding Vern's
> "Super Antennas MP1, System, as of December 2, 2010.
> Sincerely, Danny Dyer, Wb4idu, Toccoa, GA. email
> ddyer1@gmail.com
Disclaimer: The information on this site is provided as
a public service to the blind and visually handicapped community. While we have
done our best to ensure the information provided is accurate, please realize
the use of any information on this site is solely at your discretion and we
take no responsibility for use or attempted use of this information. |
