LG VX4500 Manual LG verizon USER GUIDE VX4500 Rev. 16 ************************************************ Transcriber’s notes. This version is not authorized by Verizon or LG Electronics. This (LGVX 4500 Manual)is being made available for informational purposes only . . . it is not endorsed, approved, or developed by VZW or LG. r is the symbol for the ring around the (OK) button. (OK) is the button in center of (r) key. () are used to surround key names. [] are used to surround transcriber’s inputs (Explanations) or sometimes what the LCD screen says visually. l is the symbol for the up-down long key on the left side of phone. v is the symbol for the small voice command key on bottom left side of phone. Normally when selecting something either the (l) key ends or (r) ring top or bottom can be used. When “Select” is used in this manual it means to arrow up or down using the top or bottom of (l) key or top or bottom of (r) ring. All page numbers refer to print pages. Hint: I’ve tried to put the print page numbers [which are at bottom of pages] in as Page x to enable searching by screen readers. This version of the manual is made from the ASCII version of the PDF file. Please advise me of any mistakes you notice. Lynn Roberts n8lxk@earthlink.net Phone Overview Earpiece [Top inside of lid] LCD Screen [Displays messages and indicator icons][Below earpiece on inside of flip lid]. Microphone [Bottom of phone under (0) key]. Headset Jack [near hinge on left side] Left Side Key (l) [This is one long key on left side of case, which can be pushed at bottom and top ends to adjust the ringer volume in standby mode and the earpiece volume during a call]. [Pushing the top part normally increases and pushing the bottom part decreases] [Pushing bottom part also acts as a “Manner mode” toggle. When the lid is closed] [It also can be used in navigating through choices in a menu] Voice Command Key (v) [Small key on bottom left side of phone] Use for quick access to Voice Commands and Driving Mode. [Also used to start voice memos when used during a call]. (Left Soft Key) [above (send)][Puts phone into menu] Navigation Key (r) [ring around (OK) button] Use (r) for quick access to messages, Mobile Web, Get It Now. [Also Speaker mode access][It also used to move up or down in selections of menus]. (OK) button is in center of (r) ring. (Speaker Key) [Top of (r) ring] Used to toggle Speaker mode On/Off. (Right Soft Key) Used to select an action within a Menu. [To the right of (r) ring][Also brings up Contacts List when pressed in standby mode] Message Key Press bottom of (r) ring to retrieve or send voice and text messages. SEND Key [above (1)] Press (SEND) to place or answer calls. Clear Key (CLR) [above (2) between (SEND) and (END) keys] Press to delete a single space or character. Press and hold to delete entire words. Press this key once in a menu to go back one level. END/POWER Key [above (3)] Press (END) to turn the power on/off and to end a call. Also acts as a clear key to return the phone to the main standby display screen. [Standby mode] Note: When ending a call press (END) key twice to insure you end the call and are back to standby mode. Alphanumeric Keypad (1) through (0) [(5) has two bumps on it][Also used to input letters when creating contacts]. Manner Mode Key (*) Used to set the Manner mode (from standby mode press and hold (*) for about 3 seconds). [Also is shift key when inputting text][To left of (0)] [This is the (star) key used in responding to requests for you to press “Star”.] Lock Mode Key (# or pound) Used in standby mode to set the lock function by pressing and holding the key for about 3 seconds. [Also is space when inputting text][To right of (0)][This is the pound key is used in response to requests to press “Pound”.] ************************************************* Contents [Topic followed by print page number] Welcome 7 Check Accessories 7 Important Information 7 FCC RF Exposure Infomation 10 Phone Overview 12 Menus Overview 14 Getting Your Phone Started 16 The Battery 16 Turning the Phone On and Off 17 Screen Icons 18 Making Calls 19 Receiving Calls 19 Quick Access to Convenient Features 20 Manner Mode 20 Silence All Mode 20 Lock Mode 21 Mute Function 21 Volume Quick Adjustment 21 Call Waiting 22 Caller ID 22 Speed Dialing 23 Voice Command 23 Entering and Editing Information 24 Text Input 24 Text Input Examples 26 Contacts in Your Phone’s Memory 28 The Basics of Storing Contacts Entries 28 Options to Customize Your [Contacts] 30 Adding or Changing the Group 30 Changing the Call Ringer 31 Changing the Message Ringer 31 Adding or Changing the Memo 32 Adding or Changing the Picture ID 32 Changing the Secret Setting 33 Adding or Changing the URL 33 Page 1 Adding Speed Dial 34 Editing Contacts Entries 35 Adding Another Phone Number 35 Default Numbers 36 Editing Stored Phone Numbers 36 Editing Stored Names 37 Editing Customized [Options] 37 Deleting 38 Deleting a Phone Number from a Contact 38 Deleting a Contact Entry 38 Additional Ways to Delete a Contact 38 Deleting a Speed Dial 39 Phone Numbers With Pauses 40 Storing a Number With Pauses 40 Adding a Pause to an Existing Number 41 Searching Your Phone’s Memory 42 Scrolling Through Your [Contacts] 42 Searching by Letter 42 Searching [Options] 43 Making a Call From Your Phone’s Memory 44 From [Contacts] 44 From Recent Calls 44 Voice Command 45 Prepending a Stored Number 45 Using Phone Menus 46 Menu Access 46 Contacts (Menu 1) 47 List [Contacts] 48 New Number 48 New E-mail 49 Groups 49 Speed Dials 50 My VCard 50 Recent Calls (Menu 2) 51 Dialed Calls 52 Received Calls 52 Page 2 Missed Calls 53 Erase Calls 53 Call Timer 54 1x Packet Counter 54 Messages (Menu 3) 55 New Message Alert 55 Access and [Options] 56 Voice Mail 57 New Message 57 The Basics of Sending a Message 57 Customizing the Message Using [Options] 58 Using Contacts to Send a Message 59 Text [Options] 60 Message Icon Reference 61 Inbox 61 Out of Memory Warning 62 Viewing Your Inbox 62 Outbox 63 Saved 63 Msg Settings 64 Auto Save 65 Auto Delete 65 Callback number 65 Msg Alerts 65 Signature 65 Direct View 65 Entry Mode 65 Edit Voice Mailbox number 65 Quick-Text 66 Auto Play 66 Font Size 66 Erase All 66 Get It Now (Menu 4) 67 Get Apps 68 Get Info 69 Mobile Web (Menu 5) 71 Page 3 Start Browser 72 Ending a MiniBrowser Session 72 Navigating Through the Browser 72 Initiating a Phone Call From Minibrowser 74 Web Messages 75 Alert Beep 75 My Media (Menu 6) 76 Graphics 76 Music 77 Message Objects 77 Voice (Menu 7) 78 Start Commands 79 Voice Memos 80 Voice Settings 81 Help 83 Tools (Menu 8) 84 Alarm Clock 84 Scheduler 85 Notepad 86 Ez Tip Calc 87 Calculator 87 World Clock 87 Settings (Menu 9) 88 Sounds 88 Ringers 88 Key Tone 89 Volume 89 Alerts 90 Service Change 90 Minute Beep 90 Call Connect 90 Back To Top 90 ERI Sounds 90 Power On/Off Tone 91 Display 91 Banner 91 Page 4 Backlight 92 Main LCD 92 Key Light Timer 93 Screens 93 Menu Style 93 Clocks 94 Theme Colors 94 Status LED Colors 95 Contrast 95 Fonts 96 Calling Digits 96 Text Editor 96 Language 96 System 97 Select System 97 Set NAM 97 Auto NAM 98 Serving System 98 Security 99 Lock Phone 99 Restrict 100 Emergency #s 100 Change Code 101 Erase [Contacts] 101 Reset Default 102 Call Setup 102 Auto Retry 102 Answer Call 103 Auto-Answer 103 One-Touch Dial 104 Voice Privacy 104 Auto Volume 105 TTY Mode 105 1x Data 106 Data/Fax 106 Select Port 107 Page 5 Port Speed 107 Location 108 Phone Info 108 My Phone Number 108 S/W Version 109 Icon Glossary 109 Shortcut Help 109 Safety 110 TIA Safety Information 110 Exposure to Radio Frequency Signal 110 Antenna Care 110 Phone Operation 111 Tips on Efficient Operation 111 Driving 111 Electronic Devices 111 Pacemakers 111 Hearing Aids 112 Other Medical Devices 112 Health Care Facilities 112 Vehicles 112 Posted Facilities 113 Aircraft 113 Blasting Areas 113 Potentially Explosive Atmosphere 113 For Vehicles Equipped with an Air Bag 113 Charger and Adapter Safety 114 Battery Information and Care 114 Safety Information 115 FDA Consumer Update 118 Consumer Information on SAR 126 10 Driver Safety Tips 128 Accessories 131 Warranty Information 133 Index 136 Page 6 Welcome Congratulations for choosing the advanced and compact VX4500 cellular phone, designed to operate with the latest digital mobile communication technology, Code Division Multiple Access (CDMA). Along with the many advanced features of the CDMA system, such as greatly enhanced voice clarity, this phone offers: . Large, easy-to-read, 8-line backlight LCD with status icons. . Paging, messaging, voice mail, and caller ID. . 18-key keypad. . Voice Commands. . Menu, List and Keypad Readout. . Announce Mode/Driving Mode. . Long battery standby and talk time. . Menu-driven interface with prompts for easy operation and configuration. . Any key answer, auto answer, auto retry, one-touch and speed dialing with 99 memory locations. . Bilingual (English and Spanish) capabilities. Check Accessories Your mobile phone comes with a rechargeable battery and a one-slot desktop charger. Please verify that these accessories are included. Important Information This user’s guide provides important information on the use and operation of your phone. Please read all the information carefully prior to using the phone for the best performance and to prevent any damage to or misuse of the phone. Any unapproved changes or modifications will void your warranty. Page 7 FCC Part 15 Class B Compliance This device and its accessories comply with part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device and its accessories may not cause harmful interference, and (2) this device and its accessories must accept any interference received, including interference that causes undesired operation. Technical Details The VX4500 is a dual-band phone that operates on both Code Division Multiple Access (CDMA) frequencies: cellular services at 800 MHz and Personal Communication Services (PCS) at 1.9 Ghz. CDMA technology uses a feature called DSSS (Direct Sequence Spread Spectrum) that enables the phone to keep communication from being crossed and to use one frequency channel by multiple users in the same specific area. This results in a 10-fold capacity increase when compared with analog mode. In addition, features such as soft/ softer handoff, hard Handoff, and dynamic RF power control technologies combine to reduce call interruptions. The Cellular and PCS CDMA networks consist of MSO (Mobile Switching Office), BSC (Base Station Controller), BTS (Base station Transmission System), and MS (Mobile Station). The following table lists some major CDMA standards. Page 8 [Table here] CDMA Standard Designator Description Basic Air Interface TIA/EIA-95A TSB-74 CDMA Dual-Mode Air Interface 14.4 kbps radio link protocol and inter-band operations ANSI J-STD-008 TIA/EIA-IS2000 ANSI TIA/EIA 553A IS-95 adapted for PCS frequency band cdma2000 1xRTT AirInterface Advanced Mobile Phone Service Network TIA/EIA/IS-634 MAS-BS TIA/EIA/IS/651 PCSC-RS TIA/EIA/IS-41-C Intersystem operations TIA/EIA/IS-124 Nom-signaling data comm. Service TIA/EIA/IS-96-B Speech CODEC TIA/EIA/IS-99 Async Data and Fax TIA/EIA/IS-637 Short message service TIA/EIA/IS-657 Packet Data IS-801 Position Determination Service (gpsOne) TIA/EIA/IS-707-A High Speed Packet Data Performance TIA/EIA/IS-97 Cellular base station TIA/EIA/IS-98 Cellular mobile station ANSI J-STD-018 PCS personal station ANSI J-STD-019 PCS base station TIA/EIA/IS-125 Speech CODEC * TSB-74: Protocol between an IS-95A system and ANSI J-STD-008 1xRTT system receives twice as many subscribers in the wireless section as IS-95. Its battery life is twice as long as IS-95. High-speed data transmission is also possible. Page 9 FCC RF Exposure Information WARNINGl Read this information before operating the phone. In August 1996, the Federal Communications Commission (FCC) of the United States, with its action in Report and Order FCC 96-326, adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U. S. and international standards bodies. The design of this phone complies with the FCC guidelines and these international standards. Bodily Contact During Operation This device was tested for typical use with the back of the phone kept 3/4 inches (2 cm) from the body. To comply with FCC RF exposure requirements, a minimum separation distance of 3/4 inches (2 cm) must be maintained between the user’s body and the back of the phone, including the antenna, whether extended or retracted. Third-party belt-clips, holsters, and similar accessories containing metallic components should not be used. Avoid the use of accessories that cannot maintain 3/4 inches (2 cm) distance between the user’s body and the back of the phone and have not been tested for compliance with FCC RF exposure limits. Page 10 Vehicle-Mounted External Antenna (Optional, if available.) A minimum distance of 8 inches (20 cm) must be maintained between the user/ bystander and the vehicle-mounted external antenna to satisfy FCC RF exposure requirements. For more information about RF exposure, visit the FCC website at www.fcc.gov. Caution Use only the supplied and approved antenna. Use of unauthorized antennas or modifications could impair call quality, damage the phone, void your warranty and/or result in violation of FCC regulations. Do not use the phone with a damaged antenna. If a damaged antenna comes into contact with the skin a minor burn may result. Contact your local dealer for a replacement of antenna. Page 11 Phone Overview [Picture of phone here] [Pages 12 and 13 combined] 1. Earpiece [top inside of lid] 2. Flip [open lid] 3. LCD Screen [LCD Screen Displays messages and indicator icons]. 4. Headset Jack [near hinge on left side] 5. (Left Soft Key) [above (send)] 6. Side Keys Use (l) [This is one long key on left side of case, which can be pushed at bottom and top ends] to adjust the ringer volume in standby mode and the earpiece volume during a call. [Pushing the top part normally increases and pushing the bottom part decreases] [Pushing bottom part also acts as a “Manner mode” toggle. When lid is closed] 7. SEND Key [above (1)] Use (SEND) to place or answer calls. 8. Voice Command Key (v) [Small key on bottom left side of phone] Use for quick access to Voice Commands and Driving Mode. 9. Manner Mode Key (*) Use to set the [Manner mode] mode (from standby mode press and hold (*) for about 3 seconds). [Also is shift key when inputting text] 10. (Speaker Key) [Top of (r) ring] Use to [Toggle] Speaker On/Off. 11. (Right Soft Key) Use to select an action within a Menu. [To the right of (r) ring][Also brings up Contacts List when pressed in standby mode] 12. Navigation Key (r) [ring around (OK) button] Use (r) for quick access to messages, Mobile Web, Get It Now. [Also Speaker mode access] 13. Message Key Use [on bottom of (r) ring] to retrieve or send voice and text messages. [(OK) button is in center of (r) ring] 14. Clear Key (CLR) [above (2) between (SEND) and (END) keys] Press to delete a single space or character. Press and hold to delete entire words. Press this key once in a menu to go back one level. 15. END/POWER Key [above (3)] Use (END) to turn the power on/off and to end a call. Also return to the main menu display screen. [Standby mode] 16. Alphanumeric Keypad (1) through (0) 17. Lock Mode Key (#) Use in standby mode to set the lock function by pressing and holding the key for about 3 seconds. [Also is space when inputting text] 18. Microphone [Bottom of phone under (0) key]. Page 12 and Page 13 Menus Overview view Press (Left Soft Key)[Brings up][Menu]. Press (r) [Up or down] to Scroll [Within menus] [Icon of phone book] 1 Contacts 1. List Contacts 2. New Number 3. New E-mail 4. Groups 5. Speed Dials 6. My VCard [Icon of phone receiver] 2 Recent Calls 1. Dialed Calls 2. Received Calls 3. Missed Calls 4. Erase Calls 1. Dialed Calls 2. Received Calls 3. Missed Calls 4. All Calls 5. Call Timer 1. Last Call 2. Home Calls 3. Roam Calls 4. All Calls 6. 1x Packet Counter 1. Received 2. Transmitted 3. Total [Icon of envelope] 3 Messages 1. Voice Mail 2. New Message 3. Inbox 4. Outbox 5. Saved 6. Msg Settings 1. Auto Save 2. Auto Delete 3. Callback number 4. Msg Alerts 5. Signature 6. Direct View 7. Entry Mode 8. Edit Voice Mailbox number 9. Quick-Text 0. Auto Play *. Font Size 7. Erase All 1. Inbox 2. Outbox 3. Saved 4. All [Icon of arrow] 4 Get It Now 1. Get Apps 2. Get Info [Icon of globe] 5 Mobile Web 1. Start Browser 2. Web Messages 3. Alert Beep [Icon of camera] 6 My Media 1. Graphics 2. Music 3. Message Objects 1. Small Pictures 2. Large Pictures 3. My Pictures Page 14 4. Sounds 5. My Melodies 6. Animations 7. My Animations [Icon of microphone] 7 Voice 1. Start Commands 2. Voice Memos 3. Voice Settings 1. Voice Commands 2. Sound Modes 3. Announce Alerts 4. Best Match 5. Train Words 4. Help [Icon of shapes] 8 Tools 1. Alarm Clock 2. Scheduler 3. Notepad 4. Ez Tip Calc 5. Calculator 6. World Clock [Icon of gears] 9 Settings 1. Sounds 1. Ringers 2. Key Tone 3. Volume 4. Alerts 5. Power On/Off Tone 2. Display 1. Banner 2. Backlight 3. Screens 4. Menu Style 5. Clocks 6. Theme Colors 7. Status LED Colors 8. Contrast 9. Fonts 0. Language 3. System 1. Select System 2. Set NAM 3. Auto NAM 4. Serving System 4. Security 1. Lock Phone 2. Restrict 3. Emergency #s 4. Change Code 5. Erase Contacts 6. Reset Default 5. Call Setup 1. Auto Retry 2. Answer Call 3. Auto-Answer 4. One-Touch Dial 5. Voice Privacy 6. Auto Volume 7. TTY Mode 6. 1x Data 1. Data/Fax 2. Select Port 3. Port Speed 7. Location 8. Phone Info 1. My Phone Number 2. S/W Version 3. Icon Glossary 4. Shortcut Help Page 15 The Battery NOTE: It is important to fully charge the battery before initial use of the phone. The phone comes with a rechargeable battery. Keep the battery charged while not in use in order to maximize talk and standby time. The battery charge level is shown at the top of the LCD screen. [Can also be accessed by voice by stating “Phone Status” in voice command mode] Installing the Battery To install the battery, insert the bottom of the battery into the opening on the back of the phone. Push the battery down until the latch clicks. Removing the Battery Turn the power off. Lift the release latch to detach the battery. Charging the Battery The desktop charger has a charging slot that accommodates the phone with the battery attached or the battery by itself. Warningl Use only the desktop charger provided with the phone. Using any (desktop) charger other than the one included with the VX4500 may damage your phone or battery. 1. Plug the charger into a wall outlet. The phone must be charged from a 120V AC power source. 2. Insert the phone with an installed battery, or the battery by itself, into the charging slot. The red light indicates the battery is charging and the green light indicates the battery is fully charged. The charge time varies depending upon the battery level. The maximum charge time for a fully discharged battery is 3 hours. Page 16 Battery Charge Level The battery charge level is shown at the top right of the LCD screen. When the battery charge level becomes low, the low battery sensor alerts you in three ways: sounding an audible tone, blinking the battery icon, and displaying LOW. [Can also be accessed by voice by stating “Phone Status” in voice command mode] BATTERY WARNINGl If the battery charge level becomes exceedingly low, the phone automatically switches off and any function in progress is not saved. [Graphic showing 4 bars is fully charged and no bars is fully discharged] Turning the Phone On and Off Turning the Phone On 1. Install a charged battery or connect the phone to an external power source such as a cigarette lighter charger or handsfree car kit. 2. Press (END) a few seconds until the LCD screen lights up. [Music plays] NOTE: Like any other radio device, avoid any unnecessary contact with the antenna while your phone is on. Turning the Phone Off 1. Press (END) and hold until the display turns off. [Music plays] Signal Strength Call quality depends on the signal strength in your area. The signal strength is indicated on the screen as the number of bars [Also available by audio utilizing “Phone status”] next to the signal strength icon: The more bars, the better the signal strength. If the signal quality is poor, move to an open area. If you are in a building, the reception may be better near a window. Page 17 Getting Your Phone Started Screen Icons When the phone is powered on, the top line of the LCD screen displays icons indicating the status of the phone. Icon Description [Icon of antenna symbol and 6 bars] Signal strength indicator. The strength of the signal received by the phone is indicated by the number of bars displayed. [Icon of D] Digital indicator. Digital service is available. [Icon of a triangle] Roaming indicator. The phone is outside of the home service area. [Icon of box surrounding 2 tape reels] New voice mail indicator. [Icon of circle with + in center with 3 lines after it] Location on. [Icon of circle with + in center] E911 only. [Icon of box surrounding 2 tape reels and a box behind it] New text and voice message indicator. [Icon of battery showing 4 bars] Battery indicator. Indicates battery charge level. [Icon of envelope] New text message indicator or Browser message. [Icon of phone handset] In use indicator. A call is in progress. * No icon indicates the phone is in standby mode. [Icon of phone handset with line through it] No service indicator. The phone is not receiving a system signal. [Icon 1x] IS-2000 [Icon of 2 bold arrows pointing left and right] 1X Data Active. [Icon of 2 faint arrows pointing left and right] 1X Data Dormant. [Icon of circular arrow] QNC Data Active. [Icon of phone vibrating] In vibrate [mode]. [Icon of musical note with line through it] Silence all [mode]. [Icon of handset over keys] TTY [mode]. [Icon of lock] SSL. [Icon of head talking] Announce Alerts [on]. [Icon of car] Driving Mode. [Icon of head with l beside it] Announce Mode. Page 18 Making Calls 1. Make sure the phone is turned on. If not, press (END). 2. Enter the phone number (include the area code if needed). 3. Press (SEND). [If connect beep is on it will be heard before call goes through] If the phone is locked, enter the lock code. Call Failed [Visual]- indicates the call did not go through. Restricted [Visual]- indicates outgoing calls are in restricted mode. 4. Press (END) or the side keys twice to end the call. Correcting Dialing Mistakes If you make a mistake while dialing a number, press (CLR) once to erase the last digit entered or hold (CLR) down for at least 2 seconds to delete all digits. Redialing Calls Press (SEND) twice to redial the last number you dialed. The last 30 numbers are stored in the call history list and you can also select one of these to redial. Receiving Calls 1. When the phone rings or vibrates press (SEND) to answer. [Or open lid] 2. Press (END) or the side keys (l) twice to end the call. NOTE: If you press (END) or the side keys (l) while the phone is ringing, the ringing or vibration is muted for that call. NOTE: If the phone is restricted, you can only dial phone numbers saved in the Emergency Numbers or your [Contacts]. To turn off this function: Menu -) Settings -) Security -) Enter Lock Code -) Restrict -) Off -) OK Page 19 Quick Access to Convenient Features Manner Mode Use Manner Mode in public places. When Manner Mode is set, [Vibrating phone] is displayed on the screen, the key tones are silent, and the phone is set to vibrate. [Caller-id will not talk] Manner Mode Quick Activation 1. From standby mode press (*) for 3 seconds. NOTE: The phone remains in Manner Mode even if you turn it off and back on. Manner Mode Quick Cancellation 1. Press (*) to switch to Silence All Mode or Normal Mode. NOTE: When folder [lid] is closed, you can press (l) (lower end of long left side key) for three seconds to set Manner mode. Silence All Mode Use Silence All Mode in public places. When Silence All Mode is set, [Musical note with line through it] is displayed on the screen, the key tones are silent, and the lamp blinks instead of the phone ringing or vibrating. Silence All Mode Quick Activation 1. Set the ringer to Silent by pressing (l) (lower end of side key). Silence All Mode Quick [De]Activation 1. Press (l) (upper end of side key) to switch [back] to Normal Mode. Page 20 Lock Mode Use Lock Mode to prevent others from using your phone. When Lock Mode is set, and your 4-digit password is required to use the phone. NOTE: The lock code/password is the last 4 digits of your phone number. Lock Mode Quick Activation 1. From standby mode, press (#) for 3 seconds. Lock Mode Quick Cancellation 1. Press (Right Soft Key) [Unlock] then enter your 4-digit password. Mute Function The Mute function prevents the other party from hearing your voice, but allows you to hear the other party. Mute Quick Activation 1. Press (Left Soft Key) [Mute] during a call. Mute Quick Cancellation 1. Press (Left Soft Key) again. Volume Quick Adjustment Use [Ends of] the side keys (l) to adjust the earpiece and ringer volumes. The upper [End of (l)] key increases the volume and the lower [End of] (l) key decreases the volume. . Earpiece volume can be adjusted during a call. . Ringer volume can be adjusted while the phone is ringing. NOTE: Key beep volume is adjusted through the Menu. Page 21 Call Waiting Your cellular service may offer call waiting. While a call is in progress, two beeps indicate another incoming call. When call waiting is enabled, you may put the active call on hold while you answer the other incoming call. Check with your cellular service provider for information about this function. 1. Press (SEND) to receive a waiting call. 2. Press (SEND) again to switch between calls. Caller ID Caller ID displays [Or speaks] the number of the person calling when your phone rings. If the caller’s identity is stored in Contacts, the name [Speaks the name in/lieu/of number] appears with the number. Check with your service provider to ensure they offer this feature. Page 22 Speed Dialing Speed dialing is a convenient feature that allows you to make phone calls quickly and easily with a few keystrokes. Your phone recalls the number from your Contacts, displays it briefly, and then dials it. Speed Dial number 1 is always for Voice mail. Dialing Speed Dials from 2 to 9 1. Press and hold the Speed Dial number. OR Enter the speed dial number and press (SEND). Dialing Speed Dials from 10 to 99 1. Press the first digit and then press and hold the key of the last digit. OR Enter the first and second digits and press (SEND). Voice Command Voice Command is a convenient feature that allows you to activate certain feature quickly and easily by verbal command[s]. Using this Voice Commands, you can make phone calls, confirm voice mails and missed calls, set driving/announce mode, edit the contact entries and so on. 1. Press the Voice Command key (v). 2. When prompted, say “Call Someone”. 3. When prompted, say the name entered in your Contacts. The phone will ask you to confirm the name, then [After you answer “YES”] it will dial the number associated with the Contact name. NOTE: Another way to activate Voice Command is to set Announce Mode to on. When the flip is opened you will be asked to say a command. Page 23 Entering and Editing Information Text Input You can input and edit your Banner, Schedule, Contacts, Notepad and messages. Key Functions (Right Soft Key)((Left Soft Key)): Press to scroll through the following text input modes: T9Word -) Abc -) 123 -) Symbols -) Smiley. (*) Shift: Press to change case. T9 text: T9Word -) T9WORD -) T9word Abc text: Abc -) ABC -) abc (0) Next: In T9 mode, press to display other matching words. (#) Space: Press to complete a word and insert a space. (CLR) Clear: Press to delete a single space or character. Hold to delete words. (1) Punctuation: In T9 mode, press (1) to insert punctuation in a word and complete a sentence. Page 24 Text Input Modes There are five modes for entering text, numbers, special characters, and punctuation. In a text entry field, pressing (Right Soft Key) (or (Left Soft Key)) displays a pop-up list of text modes. NOTE: It reads out the letter or the number, when the Announce Mode is On. T9Word (T9) Mode Use to type text using one keystroke per letter. The phone translates keystrokes into common words by using the letters on each key and a compressed database. Abc (Multi-tap) Mode Use to add words to the T9 database. 123 (Numbers) Mode Use to type numbers using one keystroke per number. Symbols Mode Use to insert special characters or punctuation. There are 39 special characters including “SP” which inserts a space and “LF” which forces the text to the next line. Smiley Mode Use to insert smiley graphics. There are 40 smiley characters. Changing Letter Case Using T9 and Abc text input modes you can set the capitalization. Press (*) to cycle through the following: Initial Cap (T9Word/ Abc) Only the first letter is capitalized. All subsequent letters are lower case. Page 25 Entering and Editing Information Caps Lock (T9WORD/ ABC) All letters are capitalized. Lower case (T9word/ abc) All letters are in lower case. Text Input Examples Display the text modes and select a text mode: 1. In a text entry field, press (Right Soft Key) (or (Left Soft Key)) to display text modes. 2. Press (l) to highlight the text input mode you want to use. 3. Press (OK) to select the highlighted text input mode. Using Abc (Multi-tap) Text Input 1. Press (Right Soft Key) (or (Left Soft Key)) to change to Abc mode. 2. Press (*) to change to ABC Caps Lock. 3. Press(5)(5)(5)(4). LG is displayed. Using T9 Mode Text Input To type the message “Call the office” follow these steps: 1. Press (Right Soft Key) (or (Left Soft Key)) to change to T9Word mode. 2. Press (2)(2)(5)(5). 3. Press (#) to complete the word and add a space. 4. Press (8)(4)(3)(#)(6)(3)(3)(4)(2)(3). Call the office is displayed. Page 26 Using the NEXT Key After you have finished entering a word, if the word displayed is not the one you want, press (0) to display additional choices of words from the database. 1. Press (4)(6)(6)(3). Good is displayed. 2. Press (0). The display gives you additional choices such as: Home, Gone, Hood, etc. Adding Words to the T9 Database If a word is not in the T9 database, add it using Abc (Multi-tap) mode text entry. The word is automatically added to the T9 database. 1. Press (Right Soft Key) (or (Left Soft Key)) to change to Abc (multi-tap) mode. 2. Press (2)(2)(6)(6)(6)(7). Bop is displayed. 3. Press (Right Soft Key) (or (Left Soft Key)) to change to T9 mode to add the word Bop to the T9 database. 4. Press (CLR) to erase the existing word. 5. Press (2)(6)(7). cop is displayed. 6. Press (0)(0). bop is displayed. Page 27 Contacts in Your Phone’s Memory Contacts Entries This allows you to have easy access to your most frequently dialed phone numbers. You may store up to 499 entries with up to 5 phone numbers each. Each entry may be up to 22 characters. Each phone number may be up to 48 digits. The Basics of Storing Contacts Entries [Five Visuals of screens here] 1. From standby mode enter the phone number you want to save (up to 48 digits). 2. Press (Left Soft Key) [Save]. 3. Use (r) to select a Label and press (OK). Home/ Home2/ Office/ Office2/ Mobile/ Mobile2/ Pager/ Fax/ Fax2/ None 4. Use (r) to select New Name or Existing and press (OK). NOTE: Use Existing to add another phone number to a contact already stored in memory 5. Enter a name for the phone number (up to 22 characters) and press (OK). A confirmation message is displayed briefly. Page 28 NOTE: To skip name entry, press (OK) to go to the next step. NOTE: If the information is complete, press (END) to return to the Main Menu screen. NOTE: To further customize the Contact entry, press (Left Soft Key) [Done]. 6. Continue saving the entry as a Speed Dial, press (OK) to select Speed Dial. 7. Enter a Speed Dial digit (e.g., 2) Use the keypad and press (OK) or Use to (r) highlight the Speed Dial location and press (OK). Page 29 Contacts in Your Phone’s Memory Options to Customize Your Contacts Once basic phone number and name information is stored in your Contacts, you can edit and/or customize the entries. 1. Enter the phone number and name as described on the previous page. 2. Press (Left Soft Key) [Done] to access the Edit Entry screen. 3. Use (r) to highlight the information you want to customize and press (OK). Adding or Changing the Group Allows you to manage your Contacts entries by organizing them into groups. 1. Access your Contacts and use (r) to highlight an entry, then press (OK). 2. Press (Left Soft Key) [Edit]. 3. Use (r) to highlight No Group and press (OK). 4. Use (r) to select the Group and press (OK). No Group/ Family/ Friends/ Colleagues/ Business/ School 5. Press (Left Soft Key) [Done] to continue editing the Contact entry. NOTE: You can change the name of the group, add groups, and delete groups. Page 30 Changing the Call Ringer [Note: When announce or announce alerts are on the phone will talk, it will not ring] Allows you to identify who is calling by setting different ringers for different phone numbers in your [Contacts]. It is automatically set to the default ringer when the Contact is saved. 1. Access your Contacts and use (r) to highlight an entry, then press (OK). 2. Press (Left Soft Key) [Edit]. 3. Use (r) to highlight Default Ringer and press (OK). 4. Use (r) to select the Ringer Type and press (OK). 5. Press (Left Soft Key) [Done] to continue editing the Contact entry. Changing the Message Ringer Allows you to identify who is sending you a message by setting different ringers for different phone numbers in your [Contacts]. It is automatically set to the default ringer when the Contact is saved. 1. Access your Contacts and use (r) to highlight an entry, then press (OK). 2. Press (Left Soft Key) [Edit]. 3. Use (r) to highlight Default Text Msg Ringer and press (OK). 4. Use (r) to select the Ringer Type and press (OK). 5. Press (Left Soft Key) [Done] to continue editing the Contact entry. Page 31 Contacts in Your Phone’s Memory Adding or Changing the Memo Allows you to enter up to 64 characters as a memo to the Contact entry. 1. Access your Contacts and use (r) to highlight an entry, then press (OK). 2. Press (Left Soft Key) [Edit]. 3. Use (r) to highlight Memo and press (OK). 4. Enter text and press (OK). 5. Press (Left Soft Key) [Done] to continue editing the Contact entry. Adding or Changing the Picture ID Allows the phone to display a picture to identify the caller. 1. Access your Contacts and use (r) to highlight an entry, then press (OK). 2. Press (Left Soft Key) [Edit]. 3. Use (r) to highlight Default and press (OK). 4. Use (r) to select a graphic and press (Left Soft Key) [Select]. 5. Press (Left Soft Key) [Done] to continue editing the Contact entry. Page 32 Changing the Secret Setting Allows you to hide certain entries from being displayed when the Contacts are searched. 1. Access your Contacts and use (r) to highlight an entry, then press (OK). 2. Press (Left Soft Key) [Edit]. 3. Use (r) to highlight Not Secret and press (OK). 4. Use (r) to select the Secret setting and press (OK). 5. Press (Left Soft Key) [Done] to continue editing the Contact entry. Adding or Changing the URL Allows you to enter a Web address associated with the Contact entry. 1. Access your Contacts and use (r) to highlight an entry, then press (OK). 2. Press (Left Soft Key) [Edit]. 3. Use (r) to highlight URL and press (OK). 4. Enter a Web address and press (OK). 5. Press (Left Soft Key) [Done] to continue editing the Contact entry. Page 33 Contacts in Your Phone’s Memory Adding Speed Dial 1. Access your Contacts and Use (r) to highlight an entry, then press (OK). 2. Press (Left Soft Key) [Edit]. 3. Use (r) to highlight the phone number you want to set with a Speed Dial and press (OK). 4. Press (r) to select Speed Dial. 5. Enter a Speed Dial digit. Use the Keypad and press (OK), or Use (r) to highlight the Speed Dial digit and press (OK). 6. Press (Left Soft Key) [Done] to continue editing the Contact entry, or Press (END) to return to the Main [Menu]. Page 34 Editing Contacts Entries Adding Another Phone Number From the Main Menu Screen 1. From standby mode, enter the phone number you want to save (up to 48 digits). 2. Press (Left Soft Key) [Save]. 3. Use (r) to highlight a Label and press (OK). Home/ Home2/ Office/ Office2/ Mobile/ Mobile2/ Pager/ Fax/ Fax2/ None 4. Use (r) to highlight Existing and press (OK). 5. Use (r) to highlight the existing Contact entry and press (OK). A confirmation message is displayed. Through Contacts 1. From standby mode, press (Right Soft Key) [Contacts]. Your Contacts display alphabetically. 2. Use (r) to highlight the Contact entry you want to edit, then press (OK). 3. Press (Left Soft Key) [Edit]. 4. Use (r) to highlight Add Number, then press (OK). 5. Enter the number and press (OK). 6. Use (r) to highlight a Label, then press (OK). A confirmation message is displayed. Page 35 Contacts in Your Phone’s Memory Default Numbers The phone number saved when a Contact is created is the Default Number. If more than one number is saved in a Contact entry, another number can be saved as the Default Number. NOTE: The Default Number cannot be deleted by itself. The entire Contact entry can be deleted or another number can be set as the Default Number allowing you to delete the original saved number and keep the Contact entry. Changing the Default Number 1. From standby mode, press (Right Soft Key) [Contacts]. Your Contacts display alphabetically. 2. Use (r) to highlight the Contact entry you want to edit, then press (OK). 3. Press (Left Soft Key) [Edit]. 4. Use (r) to highlight the phone number you want to set as the Default Number and press (Right Soft Key) [Options]. 5. Press (3) [Set] as Default#. A confirmation message is displayed. Editing Stored Phone Numbers 1. From standby mode, press (Right Soft Key) [Contacts]. Your Contacts display alphabetically. 2. Use (r) to highlight the Contact entry you want to edit, then press (OK). 3. Press (Left Soft Key) [Edit]. 4. Use (r) to highlight the phone number and press (OK). Page 36 5. Edit the phone number as necessary and press (OK). Editing Stored Names 1. From standby mode, press (Right Soft Key) [Contacts]. Your Contacts display alphabetically. 2. Use (r) to highlight the Contact entry you want to edit, then press (OK). 3. Press (Left Soft Key) [Edit]. 4. Use (r) to highlight the name and press (OK). 5. Edit the name as necessary and press (OK). Editing Customized Options Edit any of the Contacts options in the same manner as when the Contact is created. 1. From standby mode, press (Right Soft Key) [Contacts]. Your Contacts display alphabetically. 2. Use (r) to highlight the Contact entry you want to edit, then press (OK). 3. Press (Left Soft Key) [Edit]. 4. Use (r) to highlight the information you want to customize and press (OK). 5. Edit the information as necessary and press (OK). Page 37 Contacts in Your Phone’s Memory Deleting Deleting a Phone Number from a Contact 1. Press (Right Soft Key) [Contacts]. 2. Use (r) to highlight the Contact entry, then press (OK). 3. Press (Left Soft Key) [Edit]. 4. Use (r) to highlight the phone number to be deleted. 5. Press (Right Soft Key) [Options]. 6. Press (2) Erase Number. 7. Press (1) Erase number. A confirmation message is displayed. Deleting a Contact Entry 1. Press (Right Soft Key) [Contacts]. 2. Use (r) to highlight the Contact entry to be deleted, then press (OK). 3. Press (Right Soft Key) [Options]. 4. Press (1) [Erase Entry]. 5. Press (1) [Erase]. A confirmation message is displayed [If announce is on “Contact erased” will be spoken]. Additional Ways to Delete a Contact Once you have accessed your Contacts, pressing (Right Soft Key) [Options] at any point provides the option to erase the entry. Page 38 Deleting a Speed Dial 1. Press (Right Soft Key) [Contacts]. 2. Use (r) to highlight the Contact entry, then press (OK). 3. Use (r) to highlight the Speed Dial number. 4. Press (Left Soft Key) [Edit]. 5. Use (r) to highlight the Speed Dial number and press (OK). 6. Use (r) to highlight the Speed Dial entry and press (OK). 7. Use (r) to highlight the Speed Dial location. 8. Press (Right Soft Key) [Options]. 9. Press (2) [Remove]. 10. Press (1) [Remove]. A confirmation message is displayed. Page 39 Contacts in Your Phone’s Memory Phone Numbers With Pauses When you call automated systems such as voice mail or credit billing numbers, you often have to enter a series of numbers. Instead of entering these numbers by hand, you can store the numbers in your Contacts separated by special pause characters (P, T). There are two different types of pauses you can use when storing a number: Hard pause (P) The phone stops dialing until you press (Left Soft Key) [Release] to advance to the next number. 2-sec pause (T) The phone waits 2 seconds before sending the next string of digits. Storing a Number With Pauses 1. Press (Left Soft Key) [Menu]. 2. Press (1) [Contacts]. 3. Press (2) New Number. 4. Enter the number. 5. Press (Right Soft Key) [Pause]. 6. Use (r) to select pause type and press (OK). Hard pause/ 2-sec pause 7. Enter additional number(s) (e.g., pin number or credit card number) and press (OK). 8. Use (r) to select a Label and press (OK). 9. Enter a name (up to 22 characters). A confirmation message is displayed. Page 40 Adding a Pause to an Existing Number 1. Press (Right Soft Key) [Contacts]. 2. Use (r) to highlight the Contact entry to edit, then press (OK). 3. Press (Left Soft Key) [Edit]. 4. Use (r) to highlight the number then press (OK). 5. Press (Right Soft Key) [Pause]. 6. Press (1) [Hard pause] or (2) [2-sec pause]. 7. Enter additional number(s) and press (OK). 8. Use (l) to select the label type and press (OK). A confirmation message is displayed. Page 41 Contacts in Your Phone’s Memory Searching Your Phone’s Memory The VX4500 phone is able to perform a dynamic search of the contents in your phone’s memory. A dynamic search compares entered letters or numbers against the entries in your [Contacts]. A matching list is displayed in descending order. You can then select a number from the list to call or edit. There are several ways to search: . Scrolling Alphabetically . Searching by Letter . Searching by Options – Find Name – Find Group – Find Number – Find E-mail – Find Speed Dial – Send Message – Erase Scrolling Through Your Contacts 1. Press (Right Soft Key) [Contacts]. Contacts list is displayed alphabetically. 2. Use (r) to scroll through the list. Searching by Letter 1. Press (Right Soft Key) [Contacts]. Contacts list is displayed alphabetically. 2. Press (or press repeatedly) the key on the keypad that corresponds with the search letter. Page 42 Searching Options 1. Press (Right Soft Key) [Contacts]. 2. Press (Right Soft Key) [Options]. 3. Select the search criteria using (r) (or press the corresponding number on the keypad): (1) Find Name – Enter the character(s) to search for (such as the first letters of the name). (2) Find Number – Enter the number(s) to search. (3) Find Speed Dial – Enter the speed dial number(s) to search. (4) Find Group – Use (r) to highlight the group to search for and press (OK). (5) Find E-mail – Enter the email address to search. (6) Send Message – Enter the text and press (OK). (7) Erase – Press Erase to erase the entry. 4. A list of matches is displayed. Use (r) to highlight a matched entry. 5. Press (OK) to see more information or press (SEND) to place a call. Page 43 Contacts in Your Phone’s Memory Making a Call From Your Phone’s Memory Once you have stored phone numbers into your Contacts, you can place calls to those numbers quickly and easily. . Pressing (SEND) after you’ve searched for a phone number in Contacts or Recent Calls. . Using Speed Dialing. From Contacts 1. Press (Right Soft Key) [Contacts]. 2. Use (r) to select the Contact entry and press (OK). 3. Use (r) to select the phone number. 4. Press (SEND) to place the call. From Recent Calls 1. Press (Left Soft Key) [Menu]. 2. Press (2) Recent Calls. 3. Use (r) to select the type of recent call and press (OK). Dialed Calls/ Received Calls/ Missed Calls 4. Use (r) to highlight the phone number. 5. Press (SEND) to place the call Page 44 Voice Command Call Someone is a convenient feature that allows you to phone calls quickly and easily by saying a voice command that have recorded in your [Contacts]. To make a Voice Command: 1. From standby mode, press the Voice Command key (v). 2. When prompted, say “Call someone.” 3. When prompted, say the name of the Contact you want to call. The phone confirms and dials the phone number associated with the Contact. Prepending a Stored Number Prepend can be used if you are out of your home system area and need to add the area code to an existing number. When a Contacts entry or message callback number shows up on the display, you can add to the beginning of the original number. However, you cannot edit the original number. 1. Recall a number in your Recent Calls. 2. Press (Right Soft Key) [Options]. 3. Press (3) [Prepend]. 4. Enter the prepend digits to the phone number. 5. Press (SEND) to place the call. Page 45 Using Phone Menus Menu Access Press (Left Soft Key) [Menu] to have access to nine phone menus. There are two methods to access menus and submenus: . Use the navigation key to highlight and select, or . Press the number key that corresponds to the menu or sub[Menu]. For example: 1. Press (Left Soft Key) [Menu]. Nine menu items are displayed. Use (r) to scroll through the list of menus. 2. Press the appropriate number key corresponding to the menu item you want to select. The sub-menu list will be displayed. 3. Press the appropriate number key corresponding to the sub-menu you want to access. 4. Use (r) to highlight your preferred setting and press (OK) to select it. NOTE: Press (CLR) to go back one step while accessing the menu or selecting a setting. NOTE: Press (END) to cancel without saving. Page 46 Contacts (Menu (1)) The Contacts Menu allows you to store names, phone numbers and other information in your phone’s memory. When you access your Contacts, the number in parenthesis represents the number of entries you have stored (up to 499). Access and Options [Graphics of Contacts displays] 1. Press (Left Soft Key) [Menu]. 2. Press (1) [Contacts]. 3. Select a sub-menu. . (1) List Contacts . (2) New Number . (3) New E-mail . (4) Groups . (5) Speed Dials . (6) My VCard Page 47 Using Phone Menus List Contacts (Menu (1)(1)) Allows you to view your Contacts list. 1. Press (Left Soft Key) [Menu]. 2. Press (1) [Contacts]. 3. Press (1) List [Contacts]. 4. Options from here: . Press to scroll through your Contacts alphabetically. . Press (Right Soft Key) [Options] to select one of the following: Find Name/ Find Number/ Find Speed Dial/ Find Group/ Find E-mail/ Send Message/ Erase . Press (Left Soft Key) [New] to store a new phone number or new e-mail. New Number (Menu (1)(2)) Allows you to add a new number. NOTE: Using this sub-menu, the number is saved as a new Contact. To save the number into an existing Contact, edit the Contact entry. 1. Press (Left Soft Key) [Menu]. 2. Press (1) [Contacts]. 3. Press (2) [New Number]. 4. Enter the number and press (OK). 5. Select the label you want and press (OK). 6. Enter the name and press (OK). 7. Continue saving the entry as necessary. Page 48 New E-mail (Menu (1)(3)) Allows you to save a new e-mail address. NOTE: Using this sub-menu, the e-mail is saved as a new Contact. To save the number into an existing Contact, edit the Contact entry. 1. Press (Left Soft Key) [Menu]. 2. Press (1) [Contacts]. 3. Press (3) [New E-mail]. 4. Enter the e-mail address and press (OK). 5. Enter the name and press (OK). 6. Continue saving the entry as necessary. Groups (Menu (1)(4)) Allows you to view your grouped Contacts, add a new group, change the name of a group, or delete a whole group. 1. Press (Left Soft Key) [Menu]. 2. Press (1) [Contacts]. 3. Press (4) [Groups]. 4. Options from here: . Use (r) to highlight a group to view and press (OK). . Press (Left Soft Key) [Add] to add a new group to the list. . Use (r) to highlight a group and press (Right Soft Key) Options to change the name of the group or delete the group. Page 49 Using Phone Menus Speed Dials (Menu (1)(5)) Allows you to view your list of Speed Dials or designate Speed Dial for numbers entered in your [Contacts]. 1. Press (Left Soft Key) [Menu]. 2. Press (1) [Contacts]. 3. Press (5) [Speed Dials]. 4. Use (r) to highlight the Speed Dial position, or enter the Speed Dial digit and press (OK). 5. Use (r) to highlight the Contact and press (OK). 6. Use (r) to highlight the number and press (OK). A confirmation message is displayed. My VCard (Menu (1)(6)) Allows you to enter your own virtual business card to be used in e-mails or SMS messages. 1. Press (Left Soft Key) [Menu]. 2. Press (1) [Contacts]. 3. Press (6) [My Vcard]. 4. Select the feature you want to edit by highlighting it and pressing (OK). Page 50 Recent Calls (Menu (2)) The Recent Calls Menu is a list of the last phone numbers or Contact entries for calls you placed, accepted, or missed. It is continually updated as new numbers are added to the beginning of the list and the oldest entries are removed from the bottom of the list. NOTE: To view a quick list of all your recent calls, press (SEND) from the Main [Menu]. . [Icon of dial with right arrow] indicates a dialed call. . [Icon of dial with left arrow] indicates a received call. . [Icon of dial with right and left arrows] indicates a missed call. Access and Options [Recent calls menus graphics] 1. Press (Left Soft Key) [Menu]. 2. Press (2) [Recent Calls]. 3. Select a sub-menu. . (1) Dialed Calls . (2) Received Calls . (3) Missed Calls . (4) Erase Calls . (5) Call Timer . (6) 1x Packet Counter Page 51 Using Phone Menus Dialed Calls (Menu (2)(1)) Allows you to view the list of outgoing calls; up to 30 entries. 1. Press (Left Soft Key) [Menu]. 2. Press (2) [Recent Calls]. 3. Press (1) [Dialed Calls]. 4. Use (r) to highlight an entry, then . Press (OK) to view the entry. . Press (SEND) to place a call to the number. . Press (Right Soft Key) [Options] to select: Contact Info/ Send Msg./ Prepend/ Erase/ Erase all Received Calls (Menu (2)(2)) Allows you to view the list of incoming calls; up to 30 entries. 1. Press (Left Soft Key) [Menu]. 2. Press (2) [Recent Calls]. 3. Press (2) [Received Calls]. 4. Use (r) to highlight an entry, then . Press (OK) to view the entry. . Press (SEND) to place a call to the number. . Press (Right Soft Key) [Options] to select: Contact Info/ Send Msg./ Prepend/ Erase/ Erase all Page 52 Missed Calls (Menu (2)(3)) Allows you to view the list of missed calls; up to 30 entries. 1. Press (Left Soft Key) [Menu]. 2. Press (2) [Recent Calls]. 3. Press (3) [Missed Calls]. 4. Use (r) to highlight an entry, then . Press (OK) to view the entry. . Press (SEND) to place a call to the number. . Press (Right Soft Key) [Options] to select: Contact Info/ Send Msg./ Prepend/ Erase/ Erase all Erase Calls (Menu (2)(4)) Allows you to erase selected call list(s). 1. Press (Left Soft Key) [Menu]. 2. Press (2) [Recent Calls]. 3. Press (4) [Erase Calls]. 4. Use (r) to highlight the list of calls to erase and press (OK). Dialed Calls/ Received Calls/ Missed Calls/ All Calls 5. Press (1) [Erase] or (2) Cancel. Page 53 Using Phone Menus Using Phone Menus Call Timer (Menu (2)(5)) Allows you to view the duration of selected calls. 1. Press (Left Soft Key) [Menu]. 2. Press (2) [Recent Calls]. 3. Press (5) [Call Timer]. 4. Use (r) to highlight a call list and press (OK). Last Call/ Home Calls/ Roam Calls/ All Calls 1x Packet Counter (Menu (2)(6)) Allows you to view the list of received and transmitted data calls. 1. Press (Left Soft Key) [Menu]. 2. Press (2) [Recent Calls]. 3. Press (6) [1x Packet Counter]. 4. Use (r) to highlight a data call list and press (OK). Received/ Transmitted/ Total Page 54 Messages (Menu (3)) Text messages, pages, and the voice mail box become available as soon as the phone is powered on. . Check types of messages by pressing the message [Bottom of (r)] key. . Make a call to the callback number by pressing during a message check. . Read and edit messages saved in the outbox during transmission and send them. The phone can store up to 116 messages (for example, 1 voice message, 50 inbox text messages, 50 outbox text messages, 15 saved text messages). The VX4500 supports up to 160 characters per message including header information. The information stored in the message is determined by phone mode and service capability. Other limits to available characters per message may exist. Please check with your service provider for system features and capabilities. New Message Alert There are three ways your phone alerts you to new messages. 1. The phone displays the message on the screen. 2. One of five ring types is heard, if selected. 3. The message icon [Envelope] is displayed on the display screen. In the case of an urgent message, the icon will flash and Urgent is displayed. NOTE: If you receive the same message twice, your phone deletes the older one and the new one is stored as a DUPLICATE. Page 55 Using Phone Menus Access and Options 1. Press (Left Soft Key) [Menu]. 2. Press (3) [Messages]. 3. Select [Using (l)] a sub-menu. . (1) Voice Mail: Shows the number of messages in voice mail box. . (2) New Message: Sends a message. . (3) Inbox: Shows the list of received messages. . (4) Outbox: Shows the list of sent messages. . (5) Saved: Shows the list of saved and draft messages. . (6) Msg Settings: Selects alert type for new messages. . (7) Erase All: Deletes all stored messages. Page 56 Voice Mail (Menu (3)(1)) Allows you to view new voice messages recorded in the voice mail box. Once you exceed the storage limit, old messages are overwritten. When you have a new voice message, your phone alerts you. Checking Your Voice Mail Box 1. Press (Left Soft Key) [Menu]. 2. Press (3) [Messages]. 3. Select (1) [Voice Mail]. 4. Options from here: . Press (Left Soft Key) [Clear] to delete information, and then select Clear. . Press (SEND) to listen to the message(s). New Message (Menu (3)(2)) Allows you to send text messages, pages, and e-mail transmissions. Each message has a destination (Address 1) and information (Message). These are dependent upon the type of message you want to send. The Basics of Sending a Message 1. Press (Left Soft Key) [Menu]. 2. Press (3) [Messages]. 3. Press (2) [New Message]. 4. Enter the message destination in Address 1. Page 57 Using Phone Menus . SMS phone number for a text message. . SMS phone number for a page. . E-mail address for an e-mail message. 5. Press (OK). NOTE: To send a page, press (Left Soft Key) [Send] now. 6. Press (OK) to access the message screen. 7. Type your message (text or e-mail) then press (OK). 8. Press (Left Soft Key) [Send]. A confirmation message is displayed. NOTE: If you send an SMS message to a phone without SMS, you will still be notified that the message was sent, however the message will not be received. Customizing the Message Using Options 1. Create a new message. 2. Press (Right Soft Key) [Options]. 3. Select the option(s) to customize. Send Sends the message. Priority Gives priority to the message. Callbacknumber Inserts a pre-programmed callback number with your message. On/ Off/ Edit Deferred Delays sending the message until the programmed time frame. Immediate/ After 3 days/ After 2 days / After 1 day/ After 12 hours/ After 2 hours/ After 1 hour/ After 30 minutes Page 58 Validity Validates delivery to the Short Message Center (SMC) without being transmitted to the destination address for certain periods of time. Those messages will be deleted within the programmed time frame. Default/ 3 days/ 2 days/ 1 day/ 12 hours/ 2 hours/ 1 hour/ 30 minutes Delivery Notice Enhanced/ On Save Saves the message into the saved folder. Erase Field Deletes address or contents of message field. 4. Complete and send the message. Using Contacts to Send a Message You can designate an entry saved in your Contacts as Address 1 instead of manually entering the destination. 1. Press (Left Soft Key) [Menu]. 2. Press (3) [Messages]. 3. Select (2) [New Message]. 4. Press (Left Soft Key) [Contacts]. 5. Use (r) to highlight the Contact entry containing the destination and press (OK). 6. Use (r) to highlight the SMS phone number or e-mail address and press (OK). NOTE: The Address 1 feature allows multi-sending of up to 10 total addresses. 7. Complete the message as necessary. Page 59 Using Phone Menus Text Options While you are composing the text of a message you can insert customized text. 1. Create a new message. 2. Use (r) to highlight Message then press (OK). 3. Press (Right Soft Key) [Options]. 4. Select the option(s) to customize. Insert Quick-Text Inserts predefined phrases. Yes/ No/ Call Me/ Need Directions/ Where Are You?/ Will Call Later/ Busy/ On My Way/ Will Arrive 15 Minutes/ Thank You/ Love You Insert Object Inserts objects into the message. Small Pictures/ Large Pictures/ My Pictures/ Sounds/ My Melodies/ Animations/ My Animations Format Text Allows you to change the look of the text. Alignment/ Font Size/ Font Style/ Text Color/ Background Save Quick-Text Allows you to define phrases to insert as Insert Quick Text. Insert Signature Inserts a predefined signature. Custom/ My VCard 5. Complete and send or save the message. Page 60 Message Icon Reference [Visuals]= Icons/ Descriptions [Icon of Envelope with special character indicating sent]= Sent/ Messages saved in Short Message Center (SMC) have been transmitted. [Icon of envelope with X on top of it]= Fail/ Indicates a failed message transmission. [Icon of envelope with arrow on top]= Delivery/ Message has been delivered. [Icon of faint envelope]= Cancel/ After transmission to message center has occurred, messages that have not been delivered may be canceled by transmitting cancel message. [Icon of envelope with lock on top]= Lock/ Indicates that messages are locked. [Icon of two houses]= Multisending/ Indicates more than one designated recipient. [Icon of envelope with clock on top]= Pending/ Transmission is unavailable in a no service area. Messages are pending transmission. Pending messages are transmitted automatically when digital mode becomes available. Inbox (Menu (3)(3)) The phone alerts you in 3 ways when you receive a new message: . By displaying a message notification on the screen. . By sounding a beep or vibrating, if set. . By blinking [Envelope icon]. (Only when you get a urgent message) Received text messages, page messages, and e-mail lists may be searched and the contents viewed. Received messages are displayed from newest to oldest. Page 61 Using Phone Menus Out of Memory Warning If the memory is full, no more messages can be received until enough memory space becomes available. The message NOT ENOUGH MEMORY is displayed [Visually] and new messages are not accepted. Viewing Your Inbox 1. Press (Left Soft Key) [Menu]. 2. Press (3) [Messages]. 3. Press (3) [Inbox]. 4. Options from here: . (Left Soft Key) [Reply]. . (Right Soft Key) [Options]. Reply w Copy Replies to the SMS with the original message attached. Forward Forwards a received message to others destination address(es). Erase Deletes the selected message from the Inbox. Save Address Stores the callback number, e-mail address, and numbers in user data included in the received message into your [Contacts]. Save Object Saves pictures, animations, sounds, melodies and vcard objects in Message Objects and Contacts allowing you to use Wallpaper and Ringtone. Save Quick-Text Saves the message into the Canned message list. Page 62 Save Message Saves Inbox message into the Saved Folder. Lock/Unlock Locks or unlocks the selected message. Locked messages can not be deleted by the Erase Inbox and Erase All functions. Outbox (Menu (3)(4)) Up to 50 sent messages can be stored in the Outbox. View lists and contents of sent messages and verify whether the transmission was successful or not. 1. Press (Left Soft Key) [Menu]. 2. Press (3) [Messages]. 3. Press (4) [Outbox]. 4. Press (Left Soft Key) [Resend]. Press (Right Soft Key) [Options]. Erase Deletes the selected message from the Outbox. Lock/Unlock Locks a message so that it is not erased if the Erase Outbox or Erase All feature is used. Saved (Menu (3)(5)) Displays saved messages and draft messages. 1. Press (Left Soft Key) [Menu]. 2. Press (3) [Messages]. 3. Press (5) [Saved]. 4. Press (Left Soft Key) [Resume]. Press (Right Soft Key) [Options]. Page 63 Using Phone Menus Erase Deletes the selected message. Lock/Unlock Locks a message so that it is not erased if the Erase Saved or Erase All feature is used. Msg Settings (Menu (3)(6)) Allows you to configure ten settings for received messages. 1. Press (Left Soft Key) [Menu]. 2. Press (3) [Messages]. 3. Press (6) [Msg Settings]. 4. Use (r) to highlight one of the settings and press (OK) to select it. Auto Save Auto Save/ Prompt/ Do not Save Auto Delete On/ Off Callbacknumber On/ Off Msg Alerts Voice Mail Alert/ Text Msg Alert/ Email Alert/ Page Alert/ 2 MIN Alert Signature None/ Custom/ My VCard Direct View On/ Off Entry Mode T9 Word/ Abc/ 123 Edit Voice Mailboxnumber Quick-Text Auto Play On/ Off Font Size Small/ Normal Page 64 Message Settings Sub-Menu Descriptions Auto Save (Menu (3)(6)(1)) With this feature on, messages are automatically saved in the Outbox when transmitted. Auto Delete (Menu (3)(6(2)) With this feature on, read messages are automatically deleted when you exceed the storage limit. Callbacknumber (Menu (3)(6)(3)) Allows you to automatically send a designated callback number when you send a message. Msg Alerts (Menu (3)(6)(4)) Allows you to select the alert type for a new message. Alert types are Voice Mail Alert, Text Msg Alert, Email Alert, Page Alert, and 2 MIN Alert. Signature(Menu (3)(6)(5)) Allows you make/edit a signature to automatically send with your messages. Direct View (Menu (3)(6)(6)) Allows you to directly display the content when receiving a message. Entry Mode (Menu (3)(6)(7)) Allows you to select the default input method including T9 Word, Abc, 123. Edit Voice Mailboxnumber (Menu (3)(6)(8)) Allows you to manually enter the access number for Voice Mail Service. This number should only be used when VMS access number is not provided from the network. Page 65 Using Phone Menus Quick-Text (Menu (3)(6)(9)) Display, edit, and add Canned Messages. Auto Play (Menu (3)(6)(0)) Display automatically scrolls down while viewing messages. Font Size (Menu (3)(6)(*)) Allows you to determine the font to use when entering message content or reading text Inbox, Outbox, and Saved Msgs Folders. Erase All (Menu (3)(7)) Allows you to erase all text messages stored in your Inbox, Outbox, or Saved Msgs Folders. You can also erase all messages at the same time. 1. Press (Left Soft Key) [Menu]. 2. Press (3) [Messages]. 3. Press (7) [Erase All]. . Press (1) [Inbox] to erase all messages stored in the Inbox. . Press (2) [Outbox] to erase all messages stored in the Outbox. . Press (3) [Saved] to erase all messages stored in the Saved Msgs Folders. . Press (4) [All] to erase all messages stored in the Inbox, Outbox, and Saved Msgs Folders. 4. Press (1) [Erase all]. Confirmation message is displayed. Page 66 Get It Now (Menu (4)) Get It Now allows you to do more than just talk on your phone. Get It Now is a technology and service that allows you to download and use applications on your phone. With Get It Now, it is quick and easy to personalize your phone to your lifestyle and tastes. Just download the applications that appeal to you. With a wide range of software available, from Ring Tones to games to productivity tools, you can be assured that you can find something useful, practical, or down right entertaining. There are constantly new applications being created for your use. Downloading Applications You can download applications and use Get It Now anywhere on the Verizon Wireless network, as long as your handset has a digital signal available. Most applications do not use a network connection while in use. Incoming Calls While downloading an application, incoming calls will automatically be sent to your voice mail, if available. If you do not have voice mail, downloading will not be interrupted by an incoming call, however the caller will receive a busy signal. When using applications, an incoming call will automatically pause the application and allow you to answer the call. When you complete your call, you can resume using the application. Page 67 Using Phone Menus Access and Options [Visual of two screens] 1. Press (Left Soft Key) [Menu]. 2. Press (4) [Get It Now]. 3. Options from here: . (1) Get Apps: To add, delete, or disable Get It Now applications. . (2) Get Info: To view information about Get It Now applications. Get Apps (Menu (4)(1)) Allows you to download selected applications while displaying the Get It Now application list relayed from the Get It Now server connection. 1. Press (Left Soft Key) [Menu]. 2. Press (4) [Get It Now]. 3. Select (1) [Get Apps]. 4. Press (OK). 5. Select [Get It Now] Icon and press (OK). NOTE: Pressing the right arrow key [right side of (r) ring] will start Get It Now. Page 68 NOTE: When the file memory is full, the message “File Memory Full. To make enough storage space to install this app, the following app(s) will be temporarily disabled: vs. You can restore disabled apps by simply starting them, at no additional purchase cost. Proceed?” will be displayed. If you select Yes, the app(s) will be disabled. Get Info (Menu (4)(2)) Gives you information about the Get It Now selection key. 1. Press (Left Soft Key) [Menu]. 2. Press (4) [Get It Now]. 3. Select (2) [Get Info]. 4. Press (OK). Managing Your Get It Now Applications Add new applications and remove old ones at any time. Disabling Applications If you need more memory, but still want to be able to access the application later, try using Disable. Disabling keeps the application usage and purchase information, but removes it from memory. Restore an application when needed. 1. Access Get It Now. 2. Select Settings. 3. Use (r) to highlight Manage Apps, then press (OK). Page 69 Using Phone Menus 4. Use (r) to highlight the application to be disabled, then press (OK). 5. Select Disable. Removing Applications Only removing an application deletes it completely from the memory of the phone. To restore an application once it has been removed will require that you pay and download it again. 1. Access Get It Now. 2. Select Settings. 3. Use (r) to highlight Manage Apps, then press (OK). 4. Use (r) to highlight the application to be deleted, then press (OK). 5. Select Remove. Page 70 Mobile Web (Menu (5)) The MiniBrowser feature allows you to view internet content, via VZW with MSN, especially designed for your mobile phone. Access and selections within this feature are dependent upon your service provider. For specific information on MiniBrowser access through your phone, contact your service provider. [Visual of two screens] Access and Options 1. Press (Left Soft Key) [Menu]. 2. Press (5) [Mobile Web]. . (1) Start Browser . (2) Web Messages . (3) Alert Beep Page 71 Using Phone Menus Start Browser (Menu (5)(1)) Allows you to initiate a MiniBrowser session. 1. Press (Left Soft Key) [Menu]. 2. Press (5) [Mobile Web]. 3. Press (1) [Start Browser]. 4. A reminder of the charge will appear; press (OK) Yes to launch MiniBrowser, if required. After a few seconds, you see the Home Page. Ending a MiniBrowser Session End a MiniBrowser session by pressing (END). Navigating Through the Browser On-screen items may be presented in one of the following ways: . Numbered options You can use your numeric keypad or you can select the items by moving the cursor and pressing the appropriate Soft Keys. . Links embedded in content You can act on the options or the links by using the Soft Keys just below the display screen. . Text or numbers You can select the items by moving the cursor and pressing the appropriate Soft Keys. Scrolling Use (r) to scroll through the content if the current page does not fit on one screen. The currently selected item is indicated by a cursor on the screen. Page 72 Fast Scrolling Press and hold (r) to quickly move the cursor up and down on the current screen. Scrolling by Page Press the Side Keys (l) to move up and down a page at a time. Home Page To go to the Home Page, press and hold (SEND). View Browser Menu Press Voice Command ((v)) Key to use the Browser [Menu]. View Browser Alert Inbox Press and hold (0) key to use the Browser Alert Inbox. Soft Keys To navigate to different screens or select special functions, use the Soft Keys. The function associated with the Soft Keys can change for each page and depends on each highlighted item. (Left Soft Key) (Left Soft Key) is used primarily for first options or selecting an item but its function may change, depending on the content displayed. (Right Soft Key) (Right Soft Key) is used primarily for secondary options or a menu of secondary options. Page 73 Using Phone Menus Entering Text, Numbers, or Symbols When prompted to enter text, the current text entry method appears above the (Right Soft Key) as Alpha, Symbol, Number, Word. To change the input mode, press the (Right Soft Key). To create an upper case character, use (*). The current text method appears above the (Right Soft Key) as ALPHA and allows you to shift input case sensitivity. Clearing Out Text/Number Entered When entering text or numbers, press (CLR) to clear the last number, letter or symbol. Press and hold (CLR) to clear the input field completely. Initiating a Phone Call From Minibrowser You can make a phone call from Minibrowser if the site you are using supports the feature (the phone number may be highlighted and (Left Soft Key) appears as Call). The browser connection is terminated when you initiate the call. After you end the call, your phone returns to the screen from which you initiated the call. Page 74 Web Messages (Menu (5)(2)) Allows you to view Web messages. If there are any browser messages, the list is displayed from newest to oldest. 1. Press (Left Soft Key) [Menu]. 2. Press (5) [Mobile Web]. 3. Press (2) [Web Messages]. A message Charges will apply. Start MiniBrowser? is displayed. 4. Press (1) [Yes]. Your list of Web messages is displayed. Alert Beep (Menu (5)(3)) Allows you to select a browser alert sound. 1. Press (Left Soft Key) [Menu]. 2. Press (5) [Mobile Web]. 3. Press (3) [Alert Beep]. 4. Select an alert option. Mute/ 2 Beeps/ 4 Beeps Page 75 Using Phone Menus My Media (Menu (6)) This menu allows you to download and use a wide variety of graphics, sounds, and more. Access and Options 1. Press (Left Soft Key) [Menu]. 2. Press (6) [My Media]. 3. Select a sub-menu. . (1) Graphics . (2) Music . (3) Message Objects Graphics (Menu (6)(1)) Allows you to choose the background displayed on the phone. 1. Press (Left Soft Key) [Menu]. 2. Press (6) [My Media]. 3. Press (1) [Graphics]. 4. Use (r) to highlight your selection then press (OK) to select. Page 76 Music (Menu (6)(2)) Allows you to choose the ring tones heard for incoming calls. 1. Press (Left Soft Key) [Menu]. 2. Press (6) [My Media]. 3. Press (2) [Music]. 4. Use (r) to highlight your selection then press (OK) to select. Message Objects (Menu (6)(3)) Allows you to set objects to correspond with your messages. 1. Press (Left Soft Key) [Menu]. 2. Press (6) [My Media]. 3. Press (3) [Message Objects]. 4. Press the corresponding number key to select one of the following: [1] Small Pictures/ [2] Large Pictures/ [3] My Pictures/ [4] Sounds/ [5] My Melodies/ [6] Animations/ [7] My Animations 5. Use (r) to highlight your selection then press (OK). Page 77 Voice (Menu (7)) Voice Menu allows you to use your voice to activate certain features of your phone such as the Memo and Driving Mode. (And make the phone speak more] Access and Options [Visual of two screens] 1. Press (Left Soft Key) [Menu]. 2. Press (7) [Voice]. 3. Select a sub-menu. . (1) Start Commands . (2) Voice Memos . (3) Voice Settings . (4) Help NOTE: For voice recognition, keep surrounding area quiet and speak clearly. NOTE: When entering names in your Contacts list, avoid symbols other than letters (such as digits and punctuation marks). NOTE: Pronounce phone numbers digit by digit. Do not say “1-800” as “one eight hundred. ” Instead, say “One, eight, zero, zero. ” Page 78 Start Commands (Menu (7)(1)) Allows you to use your voice or the keypad to activate certain features of your phone. [By voice] 1. Press (Left Soft Key) [Menu]. 2. Press (7) [Voice]. 3. Press (1) [Start Commands]. 1. Call Someone: Phone call is made by saying the name, saved in the Contacts, based on List Contacts search. 2. Voicemail: Connects to *86 and Voice Mail. 3. Digit Dial: Phone call is made by saying the telephone number of 4, 7, 10 and 11 digits. 4. Service Alerts: Reads out the number of missed calls, new Voice Mails, and new messages. 5. Missed Calls: Reads out the number of new missed calls and the list of all missed calls. 6. Contact: Reads, creates, or erases the Contacts. 7. Driving: Switches the hands-free driving mode on and off. 8. Announce: Sets the Announce Mode On/Off. [Which makes phone talk much more] 9. Time and Date: Announces the time and date and displays it on the phone. 10. Phone Status: Reads out the phone status. NOTE: Voice function is recognized only in English, Spanish is not supported. For instance, “San Jose” is not recognized as [San Hose], Spanish pronunciation, but as [San Jose] as in English. Page 79 Using Phone Menus To voice-dial a name from your Contacts list: 1. Flip open the phone, and press the Voice Command Key ((v)). 2. When prompted, say “Call Someone”. 3. When prompted again, say a name from your Contacts list. 4. When asked to confirm, say “Yes”. The phone dials the person’s number. NOTE: You should select [Speak] the phone label, if the phone numbers [Choices] stored are more then two. To voice-dial a number: 1. Flip open the phone, and press the Voice Command Key. 2. When prompted, say “Digit Dial”. 3. When prompted again, say a phone number. 4. When asked to confirm, say “Yes”. The phone dials the number. Voice Memos (Menu (7)(2)) Allows you to listen to, add, and erase short verbal reminders. 1. Press (Left Soft Key) [Menu]. 2. Press (7) [Voice]. 3. Press (2) [Voice Memos]. 4. Press (Left Soft Key) [New] to record a new voice memo. 5. Use (r) to highlight your desired Voice Memo and press (Right Soft Key) [Options]. Edit title/ Memory info/ Erase/ Erase all 6. Follow the Voice Memo prompts. A confirmation message is displayed. [The following instructions are not in manual] To record a voice memo. 1. Press (Left Soft Key). 2. Press (7). 3. Press (2). 4. Press (Left Soft Key). You will hear “Please start recording at the tone.” At completion of your memo press (Left Soft key) 5. To exit this mode press (END) or close the lid. NOTE: You can also begin recording by pressing and holding the (v) key for about 3 seconds while the phone is in Standby mode. To hear the last recorded memo. 1. Press (Left Soft Key). 2. Press (7). 3. Press (2). 4. Press (OK). 5. Press (Left Soft Key). The memo will play via the earpiece, or via the speaker if Speaker Phone is turned on. 6. Pressing (Right Soft Key) will pause playing the memo. 7. Pressing (Right Soft Key) again will resume playing the memo. 8. Pressing (Left Soft Key) will stop the memo and go back to the start. 9. At the end of the memo press (END) to exit without deleting the memo, or press (Right Soft Key), (2), (1) to erase the memo. 10. To exit this mode press (END) or close the lid. To hear a previous voice memo. 1. Press (Left Soft Key). 2. Press (7). 3. Press (2). 4. Press (OK). 5. Use (l) to highlight your desired Voice Memo. [Pressing down end moves to previous memo. Pressing up end moves up in the list. If you are moving down and get low-pitched boop you have returned to latest memo.] 6. Press (Left Soft Key) to hear the memo. At the end of the memo press end to exit without deleting the memo, or press (Right Soft Key), (2), (1) to erase the memo. 10. To exit this mode press (END) or close the lid. [End of added instructions.] Page 80 Using Phone Menus Voice Settings (Menu (7)(3)) Allows you to select options for voice activation, announce alerts and recognition results; and enables you to adapt the phone to recognize your way of saying numbers. Voice Commands (Menu (7)(3)(1)) Allows you to set how you activate voice recognition. 1. Press (Left Soft Key) [Menu]. 2. Press (7) [Voice]. 3. Press (3) [Voice Settings]. 4. Press (1) [Voice Commands]. 5. Select either of the following then press (OK). . Flip open: Activates voice recognition whenever you flip open the phone. (When the phone is already open, you activate voice recognition by pressing the voice command key (v).) . Side key only: Activates voice recognition when you flip open the phone and press the voice command key (v). ([It] operates [in] Flip open Mode, when set to Announce or Driving Mode.) Sound Modes (Menu (7)(3)(2)) Allows you to set Driving/Announce/Normal Mode. 1. Press (Left Soft Key) [Menu]. 2. Press (7) [Voice]. 3. Press (3) [Voice Settings]. 4. Press (2) [Sound Modes]. 5. Select Driving Mode/ Announce Mode/ Normal Mode and press (OK). [By using (l) or top or bottom of (r) ring] Page 81 Using Phone Menus When the Announce Mode is on, the highlighted menu will be announced. For example, 1) Press (Left Soft Key) [Menu]. 2) Main menu screen appears, phone announces “Main menu”. 3) Then, phone announces the first menu item that is highlighted. 4) When the cursor is moved, the highlighted menu item is announced. 5) Menu readout only to the first sub-level. Announce Alerts (Menu (7)(3)(3)) Allows you to notify [Hear] caller ID and sender of message by voice. 1. Press (Left Soft Key) [Menu]. 2. Press (7) [Voice]. 3. Press (3) [Voice Settings]. 4. Press (3) [Announce Alerts]. 5. Select On/ Off [By using (l) or (r)] and press (OK). NOTE: When Announce Alerts is set, [Icon of head speaking] is displayed on the screen. [Visual] Best Match (Menu (7)(3)(4)) After you say a name or a number, your phone displays the recognition results-the name or number that best matches the one you said-and asks you to confirm. Select the number of results that you want your phone to display. 1. Press (Left Soft Key) [Menu]. 2. Press (7) [Voice]. 3. Press (3) [Voice Settings]. 4. Press (4) [Best Match]. Page 82 5. Select an option [Using (l) or (r)] and press (OK). . 1 Result: Displays [Or speaks] the name or number that best matches the one you said. . 4 Results: Displays [Or speaks] the four names or numbers that best match the one you said and asks you if the first one is correct. If you say “Yes,” the phone makes the call. If you say “No,” the phone suggests the second one in the list, and so on, up to the fourth result. Train Words (Menu (7)(3)(5)) Command Train is an optional personalization feature that helps your phone recognize the way you pronounce commands. If you do not get consistently good results with the commands, perform this brief, one-time session. 1. Press (Left Soft Key) [Menu]. 2. Press (7) [Voice]. 3. Press (3) [Voice Settings]. 4. Press (5) [Train Words]. 5. Select an option [Using (l) or (r)] then press (OK). [The options are] . Commands/ Digits/ Yes, No/ Contact/ Phone Label 6. Select [Using (l) or (r)] Training On/ Training Off [Default is off] and press (OK). [Speak clearly here] Help (Menu (7)(4)) Helps you to use the Voice [Menu]. 1. Press (Left Soft Key) [Menu]. 2. Press (7) [Voice]. 3. Press (4) [Help]. Page 83 Using Phone Menus Tools (Menu (8)) Your phone tools include a Alarm Clock, Scheduler, Notepad, Ez Tip Calc, Calculator, and World Clock. Access and Options [Visual of 2 screens] 1. Press (Left Soft Key) [Menu]. 2. Press (8) [Tools]. 3. Select a sub-menu. . (1) Alarm Clock . (2) Scheduler . (3) Notepad . (4) Ez Tip Calc . (5) Calculator . (6) World Clock Alarm Clock (Menu (8)(1)) Allows you to set one of four alarms. The current time is displayed at the top of the screen when you select an alarm to set. At the alarm time, Alarm 1 (or 2 or 3, as applicable) will be displayed on the LCD screen and the alarm will sound. 1. Press (Left Soft Key) [Menu]. 2. Press (8) [Tools]. 3. Press (1) [Alarm Clock]. Page 84 4. Select [Using (l) or (r)] the alarm you want to edit. . Alarm 1/ Alarm 2/ Alarm 3/ Quick Alarm 5. Use (r) to highlight the alarm time then press (OK). 6. Set the time for alarm. 7. Use (r) to highlight Once (recurring setting) and press (OK). 8. Press (r) to select one of the following: . Once/ Daily/ Mon-Fri/ Weekends 9. Use (r) to highlight Ring (ring type setting) and press (OK). 10. Use (l) or (r) to select one of the available alarm ring types and press (OK). 11. Press (Left Soft Key) [Save]. Scheduler (Menu (8)(2)) Allows you to conveniently keep and access your agenda(s). Simply store your appointments and your phone will alert you with a reminder of your appointment. 1. Press (Left Soft Key) [Menu]. 2. Press (8) [Tools]. 3. Press (2) [Scheduler]. 4. Use (r) to highlight the scheduled day. Page 85 Using Phone Menus [Left side of (r) ring] Moves cursor to the left. [Right side of (r) ring] Moves cursor to the right. [Top of (r) ring] Moves to the previous week. [Bottom of (r) ring] Moves to the next week. 5. Press (Left Soft Key) [Add]. 6. Enter your schedule information including: . Date . Time . Content . Voice . Repeating event . When to ring the alarm reminder . Which ring alarm to sound 7. Press (Left Soft Key) [Saves]. NOTE: Scheduler will not alert you during a call or during SMS transmitting. It will sound the reminder after you exit a call. Notepad (Menu (8)(3)) Allows you to read, add, edit, and erase notes to yourself. 1. Press (Left Soft Key) [Menu]. 2. Press (8) [Tools]. 3. Press (3) [Notepad]. 4. Press (Left Soft Key) [Add] to write a new note. Page 86 Ez Tip Calc (Menu (8)(4)) Allows you to quickly and easily calculate the amounts for a bill with the amount of the bill, the amount of the tip and the number of people as variables. 1. Press (Left Soft Key) [Menu]. 2. Press (8) [Tools]. 3. Press (4) [Ez Tip Calc]. Calculator (Menu (8)(5)) Allows you to calculate simple mathematical computations. You can enter numbers up to the second decimal place. 1. Press (Left Soft Key) [Menu]. 2. Press (8) [Tools]. 3. Press (5) [Calculator]. NOTE: Calculations can be made with up to 35 characters at one time (e.g., 63+78-21 would be 8 characters). World Clock (Menu (8)(6)) Allows you to determine the current time in another time zone or country. 1. Press (Left Soft Key) [Menu]. 2. Press (8) [Tools]. 3. Press (6) [World Clock]. NOTE: Press (Left Soft Key) to set to Daylight Savings Time. Page 87 Using Phone Menus Settings (Menu (9)) The Setup menu has options to customize your phone. Access and Options [Graphic of two screens] 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Select a sub-menu. . (1) Sounds . (2) Display . (3) System . (4) Security . (5) Call Setup . (6) 1x Data . (7) Location . (8) Phone Info Sounds(Menu (9)(1)) Options to customize the phone’s sounds. Ringers(Menu (9)(1)(1)) Sets ring tones for types of incoming calls. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (1) [Sounds] then press (1) [Ringers]. 4. Select Caller ID/ No Caller ID/ Restrict. 5. Use (l) or (r) to select a ringer then press (OK) to save the sound. Page 88 Key Tone (Menu (9)(1)(2)) Allows you to set the Key Tone length and touch tone playback speed. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (1) [Sounds] then press (2) [Key Tone]. 4. Select using (r) or (l) either of the following then press (OK). Normal Sends out a tone for a fixed period of time even if you keep the key pressed. Long Sends out a continuous tone for as long as you keep the key pressed. NOTE: Dual-Tone Multi Frequency (DTMF) Signaling by the simultaneous transmission of two tones, one from a group of low frequencies and another from a group of high frequencies. Each group of frequencies consists of four frequencies. Setting the Key Beep length to Long will extend the DTMF tone. Volume(Menu (9)(1)(3)) Allows you to set various volume settings. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (1) [Sounds] then press (3) [Volume]. 4. Select Ringer/ Earpiece/ Key Beep/ Speaker. 5. Adjust the volume of the ringer with (l) or (r) then press (OK) to save the setting. Page 89 Using Phone Menus Alerts (Menu (9)(1)(4)) Allows you to set any of the four Alert options to either On or Off. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (1) [Sounds] then press (4) Alerts. 4. Select an alert option. Service Change (Menu (9)(1)(4)(1)) Alerts you when service changes. When you enter a service area, the phone displays Entering Service Area message. When you leave a service area, the phone displays Leaving Service Area message. Minute Beep (Menu (9)(1)(4)2)) Alerts you 10 seconds before the end of every minute during a call. Call Connect (Menu (9)(1)(4)(3)) Alerts you when the call is connected. Back To Top (Menu (9)(1)(4)(4))[Helpful feature for visually impaired users] Alerts you when you scroll through the end of a menu list. [If Back To Top is set to on, it will give an audible boop when you cycle through choices, which can be very helpful in making your way in a menu that doesn’t talk][If you are going up, using (l) or (r) it will boop when it goes to bottom choice, if you are going down using (l) or (r) it will boop when it goes to top choice][On a 4 choice screen, phone will do high beeps in 3 of choices and boop for the fourth choice, depending on which end of (l) key or top or bottom of (r) ring] ERI Sounds (Menu (9)(1)(4)(5)) Alerts you the status of cellular service. 5. Select an option and press (OK). 6. Set On/ Off with (l) then press (OK). Page 90 Power On/Off Tone (Menu (9)(1)(5)) Allows you to set the phone to sound a tone when the phone is powered on, powered off, or both. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (1) [Sounds]. 4. Press (5) [Power On/ Off Tone]. 5. Set [choose] your selection with (r) or (l). 6. Press (OK) to save the setting. [Changing power on music is done (9)(2)(3)(2) and choices followed by (Left Soft key)][Changing power off music can’t be done.] Display (Menu (9)(2)) Options to customize the phone’s display screen. Banner(Menu (9)(2)(1)) Allows you to enter a string of up to 16 characters which display on the LCD screen. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (2) [Display]. 4. Press (1) [Banner]. 5. Enter you banner text then press (OK). Page 91 Using Phone Menus Backlight (Menu (9)(2)(2)) Allows you to set the duration for illuminating the backlight. Main LCD, Key Light Timer are set separately. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (2) [Display]. 4. Press (2) [Backlight]. 5. Choose a Backlight sub-menu and press (OK). Main LCD/ Key Light Timer 6. Choose a setting and press (OK). Timer/ Brightness If an amount of time is set for the timer option, the time starts after the last key was pressed. Main LCD (Menu (9)(2)(2)(1)) Timer Options . 7 seconds . 15 seconds . 30 seconds . Always on means that the backlight is always on while flip (cell case) is open. . Always off means that the backlight is never on. Brightness Sets the brightness level of the backlight. Page 92 Key Light Timer (Menu (9)(2)(2)(2)) . 7 seconds . 15 seconds . Always on means that the backlight is always on while flip (cellcase) is open. . Always off means that the backlight is never on. Screens (Menu (9)(2)(3)) Allows you to choose the kind of [Visual] background to be displayed on the phone. [Allows you to change power on music.] 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (2) [Display]. 4. Press (3) [Screens]. 5. Select (1) [Wallpaper]/ (2) [Power On]/ (3) [Power Off]. 6. Press (OK). 7. Select from different screens then press (OK) and (Left Soft Key) [Save]. [Changing screens for power on changes the music during powering on of phone]. [Changing screens for power off does not change music during power off sequencing]. Menu Style (Menu (9)(2)(4)) Allows you to choose whether you want the menu to show as a list or as icons. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (2) [Display]. 4. Press (4) [Menu Style]. 5. Select Icon or List and press (OK). Page 93 Using Phone Menus Clocks (Menu (9)(2)(5)) Allows you to choose the kind of clock to be displayed on the LCD screen. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (2) [Display]. 4. Press (5) [Clocks]. 5. Select (1) [Normal]/ (2) [Analog]/ (3) [Digital] then press (Left Soft Key) [Save]. Theme Colors (Menu (9)(2)(6)) Allows you to choose the color of the background screen. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (2) [Display]. 4. Press (6) [Theme Colors]. 5. Select [using (r)] Default/ Green/ Violet/ Orange then press (OK). Page 94 Status LED Colors (Menu (9(2)(7)) Allows you to choose the color of the LED Status [Visual]. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (2) [Display]. 4. Press (7) [Status LED Colors]. 5. Choose a sub-menu and press (OK). (1) Incoming Calls (2) New SMS Alerts (3) Reminders (4) Roaming Calls (5) Battery Low 6. Select the color which you want to assign. . Dynamic/ Red/ Green/ Blue/ Yellow/ Magenta/ Cyan/ Off Contrast (Menu (9)(2)(8)) Allows you to set the level of contrast for your LCD screen [Visual]. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (2) [Display]. 4. Press (8) [Contrast]. 5. Choose a Contrast sub-menu and press (OK). Main LCD/ Front LCD. 6. Use (r) [right and left sides of ring] to adjust the contrast level. Page 95 Using Phone Menus Fonts (Menu (9)(2)(9)) Allows you to set the size and color of the font. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (2) [Display]. 4. Press (9) [Fonts]. Calling Digits (Menu (9)(2)(9)(1)) 1. Select Size/ Color. 2. Press [Top or bottom of] (r) until you find the size or color you desire then press (OK) to save. Text Editor (Menu (9)(2)(9)(2)) 1. Select Size/ Color. 2. Press [Top or bottom of] (r) until you find the size or color you desire then press to save. Language (Menu (9)(2)(0)) Allows you to set the bilingual feature according to your reference. Choose between English and Spanish. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (2) [Display]. 4. Press (0) [Language]. 5. Set English/ Spanish with [Top or bottom of] (r) then press (OK). Page 96 System (Menu (9)(3)) The System menu allows you to designate specific system network settings. Select System (Menu (9)(3)(1)) Allows you to set up the phone producer’s management environment. Leave this setting as the default unless you want to alter system selection as instructed by your service provider. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (3) [System]. 4. Press (1) [Select System]. 5. Select Home Only/ Automatic then press (OK). Set NAM (Menu (9)(3)(2)) Allows you to select the phone’s NAM (Number Assignment Module) if the phone is registered with multiple service providers. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (3) [System]. 4. Press (2) [Set NAM]. 5. Select NAM1/ NAM2 then press (OK). Page 97 Using Phone Menus Auto NAM (Menu (9)(3)(3)) Allows the phone to automatically switch between programmed telephone numbers corresponding to the service provider area. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (3) [System]. 4. Press (3) [Auto NAM]. 5. Select On/ Off then press (OK). Serving System (Menu (9)(3)(4)) Identifies the channel number of a system that is served and a SID Number. This information is only for technical support. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (3) [System]. 4. Press (4) [Serving System]. Page 98 Security(Menu (9)(4)) The Security menu allows you to secure the phone electronically. Lock Phone (Menu (9)(4)(1)) Keeps your phone from unauthorized use. Once the phone is locked, it is in restricted mode until the lock code is entered. You can receive phone calls and still make emergency calls. You can modify the lock code using the New Lock code within the Security [Menu]. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (4) [Security]. 4. Enter the four-digit lock code. The lock code is commonly the last 4 digits of your phone number. 5. Press (1) Lock Phone. 6. Select an option then press (OK). Unlock The phone is never locked (Lock mode can be used). Lock The phone is always locked. When locked, you can receive incoming calls or make only emergency calls. On Power Up The phone is locked when it is turned on. Page 99 Using Phone Menus Restrict (Menu (9)(4)(2)) Allows you to restrict outgoing calls. If you set this feature to “On” you can only place calls to emergency numbers and phone numbers stored in your [Contacts]. You can still receive calls in the restrict mode. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (4) [Security]. 4. Enter the four-digit lock code. 5. Press (2) [Restrict]. 6. Select On/ Off then press (OK). Emergency #s (Menu (9)(4)(3)) Allows you to enter 3 emergency numbers You can call these emergency numbers and 911, even when the phone is locked or restricted. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (4) [Security]. 4. Enter the four-digit lock code. 5. Press (3) [Emergency #s]. 6. Select an emergency number using (r). 7. Enter an emergency phone number then press (OK). Page 100 Change Code (Menu (9)(4)(4)) Allows you to enter a new four-digit lock code. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (4) [Security]. 4. Enter the four-digit lock code. 5. Press (4) [Change Code]. 6. For confirmation, it will ask you to enter the new lock code again. Erase Contacts (Menu (9)(4)(5() Allows you to erase all of your Contacts at once. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (4) [Security]. 4. Enter the four-digit lock code. 5. Press (5) [Erase Contacts]. 6. Select Erase all #s then press (OK). Page 101 Using Phone Menus Reset Default (Menu (9)(4)(6)) Allows you to reset your phone to the factory default settings. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (4) [Security]. 4. Enter the four-digit lock code. 5. Press (6) [Reset Default]. 6. Press (OK), select Revert [using (l)] then press (OK). Call Setup (Menu (9)(5)) The Call Setup menu allows you to designate how the phone handles both incoming and outgoing calls. Auto Retry (Menu (9)(5)(1)) Allows you to set the length of time the phone waits before automatically redialing a number when the attempted call fails. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (5) [Call Setup]. 4. Press (1) [Auto Retry]. 5. Select Off/ Every 10 seconds/ Every 30 seconds/ Every 60 seconds [using (l)] then press (OK). Page 102 Answer Call (Menu (9)(5)(2)) Allows you to determine how to initiate an answered call. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (5) [Call Setup]. 4. Press (2) [Answer Call]. 5. Select [using (l)] Flip Open/ Any Key/ SEND Only then press (OK). Auto-Answer(Menu (9)(5)(3)) Allows you to select the number of rings before the phone automatically answers a call. This feature is intended for use with hands free devices, but is an independent feature of the phone and must be manually turned on/off when connected or disconnected from the device. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (5) [Call Setup]. 4. Press (3) [Auto-Answer]. 5. Select [using (l)] an option then press (OK). . Off . After 1 ring When you have an incoming call, the phone automatically responds after 1 ring. . After 3 rings When you have an incoming call, the phone automatically responds after 3 rings. Page 103 Using Phone Menus One-Touch Dial (Menu (9)(5)(4)) Allows you to initiate a speed dial call by pressing and holding the speed dial digit. If set to Disable, Speed Dial numbers designated in your Contacts will not function. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (5) [Call Setup]. 4. Press (4) [One-Touch Dial]. 5. Select Enable/ Disable [using (l)] then press (OK). Voice Privacy (Menu (9)(5)(5)) Allows you to set the voice privacy feature for CDMA calls as Enhanced or Standard. CDMA offers inherent voice privacy. Check with your service provider for availability. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (5) [Call Setup]. 4. Press (5) [Voice Privacy]. 5. Select Enhanced/ Standard [using (l)] then press (OK). Page 104 Auto Volume (Menu (9)(5)(6)) Provides a better audio experience by enabling the Auto Volume feature to control the dynamic range and volume of the sending and receiving voice across different levels of speaker and environments. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (5) [Call Setup]. 4. Press (6) [Auto Volume]. 5. Select On/ Off [using (l)] then press (OK). TTY Mode (Menu (9)(5)(7)) Allows you to attach a TTY device enabling you to communicate with parties also using a TTY device. A phone with TTY support is able to translate typed characters to voice. Voice can also be translated into characters and then displayed on the TTY. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (5) [Call Setup]. 4. Press (7) [TTY Mode]. 5. Press (OK). 6. Select TTY Full/ TTY+TALK/ TTY+HEAR/ TTY Off [using (l)] then press (OK). Page 105 Using Phone Menus 1x Data (Menu (9)(6)) This menu allows you to use wireless data communication services. Wireless data communication services refers to the utilization of subscriber terminals for access to the internet with personal computers or laptops at 19.2 Kbps or at a maximum of 230.4 Kbps. The connection speed depends on your carrier’s network and other variables. Contact communication information specifications must match the network. Data/Fax (Menu (9)(6)(1)) Allows you to use your phone to transmit data and faxes. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (6) [1x Data]. 4. Press (1) [Data/ Fax]. 5. Select Off/ Fax In Once/ Fax In Always/ Data In Once / Data In Always [using (l)] then press (OK). NOTE: The Data Connection Kit allows you to connect your PC or PDA to your LG wireless phone, freeing you from having to locate a telephone outlet. You can send or receive an e-mail, a fax, or access the Internet anytime, anywhere. Page 106 Select Port (Menu (9)(6(2)) Allows you to select the data port. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (9) [1x Data]. 4. Press (2) [Select Port]. 5. Select RS-232C (COM Port)/ Closed [using (l)] then press (OK). Port Speed (Menu (9)(6)(3)) Allows you to set the port speed. Set the port speed based on your carrier’s network. Contact your carrier to determine the maximum available speed. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (6) [1x Data]. 4. Press (3) [Port Speed]. 5. Select 19200/ 115200/ 230400 [using (l)] then press (OK). NOTE: When using the 1X HSPD data service via an RS-232C data cable, the port speed is set to 115,200 (230,400 is not supported). When using the 1X HSPD data service via a USB data cable, you may get better port speed if the port speed is set to 230,400 rather than 115,200. Page 107 Using Phone Menus Location (Menu (9)(7)) Menu for GPS (Global Positioning System: Satellite assisted location information system) mode. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (7) [Location]. 4. Select Location On/ E911 Only [using (l)] then press (OK). NOTE: GPS satellite signals are not always transmitted, especially under bad atmospheric and environmental conditions, indoors or otherwise. Phone Info (Menu (9)(8)) The Phone Info menu provides you with specific information pertaining to your phone model. My Phone Number (Menu (9)(8)(1)) Allows you to view your phone number. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (8) [Phone Info]. 4. Press (1) [My Phone Number]. Page 108 S/W Version (Menu (9)(8)(2)) Allows you to view the software, PRL, ERI, and browser version. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (8) [Phone Info]. 4. Press (2) [S/W Version]. Icon Glossary (Menu (9)(8)(3)) Allows you to view [visually] all the icons and their meanings. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (9)[Phone Info]. 4. Press (3) [Icon Glossary]. Shortcut Help (Menu (9)(8)(4)) Allows you to view condensed information about using the phone. 1. Press (Left Soft Key) [Menu]. 2. Press (9) [Settings]. 3. Press (8) [Phone Info]. 4. Press (4) [Shortcut Help]. . From the Standby screen, press (CLR). Page 109 Safety TIA Safety Information The following is the complete TIA Safety Information for wireless handheld phones. Exposure to Radio Frequency Signal Your wireless handheld portable phone is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) signals. In August, 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for handheld wireless phones. Those guidelines are consistent with the safety standards previously set by both U. S. and international standards bodies: ANSI C95. 1 (1992) * NCRP Report 86 (1986) ICNIRP (1996) American National Standards Institute; National Council on Radiation Protection and Measurements; International Commission on Non-Ionizing Radiation Protection Those standards were based on comprehensive and periodic evaluations of the relevant scientific literature. For example, over 120 scientists, engineers, and physicians from universities, government health agencies, and industry reviewed the available body of research to develop the ANSI Standard (C95. 1). The design of your phone complies with the FCC guidelines (and those standards). Antenna Care Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could damage the phone and may violate FCC regulations. Page 110 Phone Operation NORMAL POSITION: Hold the phone as you would any other telephone with the antenna pointed up and over your shoulder. Tips on Efficient Operation For your phone to operate most efficiently: Do not touch the antenna unnecessarily when the phone is in use. Contact with the antenna affects call quality and may cause the phone to operate at a higher power level than otherwise needed. Driving Check the laws and regulations on the use of wireless phones in the areas where you drive and always obey them. Also, if using your phone while driving, please observe the following: . Give full attention to driving — driving safely is your first responsibility; . Use hands-free operation, if available; . Pull off the road and park before making or answering a call if driving conditions or the law so require. Electronic Devices Most modern electronic equipment is shielded from RF signals. However, certain electronic equipment may not be shielded against the RF signals from your wireless phone. Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of six (6) inches be maintained between a handheld wireless phone and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research. Page 111 Safety Persons with pacemakers: • Should ALWAYS keep the phone more than six (6) inches from their pacemaker when the phone is turned ON; • Should not carry the phone in a breast pocket; • Should use the ear opposite the pacemaker to minimize the potential for interference; • Should turn the phone OFF immediately if there is any reason to suspect that interference is taking place. Hearing Aids Some digital wireless phones may interfere with some hearing aids. In the event of such interference, you may want to consult your service provider (or call the customer service line to discuss alternatives.) Optional for each phone manufacturer. Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if it is adequately shielded from external RF energy. Your physician may be able to assist you in obtaining this information. Health Care Facilities Turn your phone OFF in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may use equipment that could be sensitive to external RF energy. Vehicles RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles. Check with the manufacturer or its representative regarding your vehicle. You should also consult the manufacturer of any equipment that has been added to your vehicle. Page 112 Posted Facilities Turn your phone OFF in any facility where posted notices so require. Aircraft FCC regulations prohibit using your phone while in the air. Switch OFF your phone before boarding an aircraft. Blasting Areas To avoid interfering with blasting operations, turn your phone OFF when in a “blasting area” or in areas posted: “Turn off two-way radio”. Obey all signs and instructions. Potentially Explosive Atmosphere Turn your phone OFF when in any area with a potentially explosive atmosphere and obey all signs and instructions. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Areas with a potentially explosive atmosphere are often, but not always marked clearly. Potential areas may include: fueling areas (such as gasoline stations); below deck on boats; fuel or chemical transfer or storage facilities; vehicles using liquefied petroleum gas (such as propane or butane); areas where the air contains chemicals or particles (such as grain, dust, or metal powders) and any other area where you would normally be advised to turn off your vehicle engine. For Vehicles Equipped with an Air Bag An air bag inflates with great force. DO NOT place objects, including either installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If in vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result. Page 113 Safety Charger and Adapter Safety . The charger and adapter are intended for indoor use only. . Do not expose the battery charger or adapter to direct sunlight or use it in places with high humidity, such as a bathroom. Battery Information and Care . Please dispose of your battery properly or take it to your local wireless carrier for recycling. . Do not dispose of your battery in fire or with hazardous or flammable materials. . Never store your phone in temperatures less than -4° F or greater than 122° F. . Never use an unapproved battery since this could damage the phone and/or battery and could cause the battery to explode. . The battery does not need to be fully discharged before recharging. . Use only LG-approved chargers specific to your phone model since they are designed to maximize battery life. . Do not disassemble or short-circuit the battery. . Keep the battery’s metal contacts clean. . Replace the battery when it no longer provides acceptable performance. The battery can be recharged several hundred times before replacement. . Recharge the battery after long periods of non-use to maximize battery life. . Battery life will vary due to usage patterns and environmental conditions. . Use of extended backlighting, MiniBrowser, and data connectivity kits affect battery life and talk/standby times. Page 114 Safety Information Please read and observe the following information for safe and proper use of your phone and to prevent damage. Also, keep the user’s guide in an accessible place at all the times after reading it. Explosion, Shock, and Fire Hazards . Make sure that no sharp-edged items such as animal’s teeth, nails, come into contact with the battery. There is a risk of this causing a fire. . Do not use harsh chemicals (such as alcohol, benzene, thinners, etc.) or detergents to clean your phone. There is a risk of this causing a fire. . When riding in a car, do not leave your phone or set up the hands-free kit near to the air bag. If wireless equipment is improperly installed and the air bag is activated, you may be seriously injured. . Do not handle the phone with wet hands while it is being charged. It may cause an electric shock or seriously damage your phone. . Do not drop, strike, or shake your phone severely. Such actions may harm the internal circuit boards of the phone. . Be careful that children do not swallow any parts such as rubber plugs (earphone, connection parts of the phone, etc.). This could cause asphyxiation or suffocation. . Do not use your phone in high explosive areas as the phone may generate sparks. . Do not put your phone in a place subject to excessive dust and keep the minimum required distance between the power cord and heat sources. . Unplug the power cord prior to cleaning your phone, and clean the power plug pin when it is dirty. Page 115 Safety . Do not damage the power cord by bending, twisting, pulling, or heating. Do not use the plug if it is loose as it may cause a fire or electric shock. . When using the power plug, ensure that it is firmly connected. If it is not, it may cause excessive heat or fire. . Do not place any heavy items on the power cord. Do not allow the power cord to be crimped as it may cause fire or electric shock. . Do not disassemble the phone. . Do not place or answer calls while charging the phone as it may short-circuit the phone and/or cause electric shock or fire. . If you put your phone in a pocket or bag without covering the receptacle of the phone (power plug pin), metallic articles (such as a coin, paperclip or pen) may short-circuit the phone. Always cover the receptacle when not in use. . Do not short-circuit the battery. Metallic articles such as a coin, paperclip or pen in your pocket or bag may short-circuit the + and – terminals of the battery (metal strips on the battery) upon moving. Short-circuit of the terminal may damage the battery and cause an explosion. . Never place your phone in a microwave oven as it will cause the battery to explode. General Warnings and Cautions . Only use the batteries, antennas, and chargers provided by LG. The warranty will not be applied to products provided by other suppliers. . Store the battery in a place out of reach of children. . Using a damaged battery or placing a battery in your mouth may cause serious injury. Page 116 . Do not place items containing magnetic components such as a credit card, phone card, bank book or subway ticket near your phone. The magnetism of the phone may damage the data stored in the magnetic strip. . Do not hold or let the antenna come in contact with your body during a call. . Talking on your phone for a long period of time may reduce call quality due to heat generated during use. . When the phone is not used for a long period time, store it in a safe place with the power cord unplugged. . Using the phone in proximity to receiving equipment (i.e., TV or radio) may cause interference to the phone. . Only authorized personnel should service the phone and its accessories. Faulty installation or service may result in accidents and consequently invalidate the warranty. . Do not use the phone if the antenna is damaged. If a damaged antenna contacts skin, it may cause a slight burn. Please contact an LG Authorized Service Center to replace the damaged antenna. . Do not use the phone in areas where its use is prohibited. (For example: aircraft). . Do not immerse your phone in water. If this happens, turn it off immediately and remove the battery. If the phone does not work, take it to an LG Authorized Service Center. . The power cord on this product will expose you to lead, a chemical known to the State of California to cause (cancer, and) birth defects or other reproductive harm. Wash hands after handling. Page 117 Safety FDA Consumer Update The U. S. Food and Drug Administration’s Center for Devices and Radiological Health Consumer Update on Mobile Phones: 1. Do wireless phones pose a health hazard? The available scientific evidence does not show that any health problems are associated with using wireless phones. There is no proof, however, that wireless phones are absolutely safe. Wireless phones emit low levels of radiofrequency energy (RF) in the microwave range while being used. They also emit very low levels of RF when in the standby mode. Whereas high levels of RF can produce health effects (by heating tissue), exposure to low level RF that does not produce heating effects causes no known adverse health effects. Many studies of low level RF exposures have not found any biological effects. Some studies have suggested that some biological effects may occur, but such findings have not been confirmed by additional research. In some cases, other researchers have had difficulty in reproducing those studies, or in determining the reasons for inconsistent results. 2. What is the FDA’s role concerning the safety of wireless phones? Under the law, the FDA does not review the safety of radiation-emitting consumer products such as wireless phones before they can be sold, as it does with new drugs or medical devices. However, the agency has authority to take action if wireless phones are shown to emit radiofrequency energy (RF) at a level that is hazardous to the user. In such a case, the FDA could require the manufacturers of wireless phones to notify users of the health hazard and to repair, replace, or recall the phones so that the hazard no longer exists. Although the existing scientific data do not justify FDA regulatory actions, the FDA has urged the wireless phone industry to take a number of steps, including the following: Page 118 . Support needed research into possible biological effects of RF of the type emitted by wireless phones; . Design wireless phones in a way that minimizes any RF exposure to the user that is not necessary for device function; and . Cooperate in providing users of wireless phones with the best possible information on possible effects of wireless phone use on human health. The FDA belongs to an interagency working group of the federal agencies that have responsibility for different aspects of RF safety to ensure coordinated efforts at the federal level. The following agencies belong to this working group: . National Institute for Occupational Safety and Health . Environmental Protection Agency . Occupational Safety and Health Administration . National Telecommunications and Information Administration The National Institutes of Health participates in some interagency working group activities, as well. The FDA shares regulatory responsibilities for wireless phones with the Federal Communications Commission (FCC). All phones that are sold in the United States must comply with FCC safety guidelines that limit RF exposure. The FCC relies on the FDA and other health agencies for safety questions about wireless phones. The FCC also regulates the base stations that the wireless phone networks rely upon. While these base stations operate at higher power than do the wireless phones themselves, the RF exposures that people get from these base stations are typically thousands of times lower than those they can get from wireless phones. Base stations are thus not the subject of the safety questions discussed in this document. Page 119 Safety 3. What kinds of phones are the subject of this update? The term “wireless phone” refers here to handheld wireless phones with built-in antennas, often called “cell”, “mobile”, or “PCS” phones. These types of wireless phones can expose the user to measurable radiofrequency energy (RF) because of the short distance between the phone and the user’s head. These RF exposures are limited by FCC safety guidelines that were developed with the advice of the FDA and other federal health and safety agencies. When the phone is located at greater distances from the user, the exposure to RF is drastically lower because a person’s RF exposure decreases rapidly with increasing distance from the source. The so-called “cordless phones,” which have a base unit connected to the telephone wiring in a house, typically operate at far lower power levels, and thus produce RF exposures far below the FCC safety limits. 4. What are the results of the research done already? The research done thus far has produced conflicting results, and many studies have suffered from flaws in their research methods. Animal experiments investigating the effects of radiofrequency energy (RF) exposures characteristic of wireless phones have yielded conflicting results that often cannot be repeated in other laboratories. A few animal studies, however, have suggested that low levels of RF could accelerate the development of cancer in laboratory animals. However, many of the studies that showed increased tumor development used animals that had been genetically engineered or treated with cancer-causing chemicals so as to be pre-disposed to develop cancer in the absence of RF exposure. Other studies exposed the animals to RF for up to 22 hours per day. These conditions are not similar to the conditions under which people use wireless phones, so we don’t know with certainty what the results of such studies mean for human health. Three large epidemiology studies have been published since December 2000. Between them, the studies investigated any Page 120 possible association between the use of wireless phones and primary brain cancer, glioma, meningioma, or acoustic neuroma, tumors of the brain or salivary gland, leukemia, or other cancers. None of the studies demonstrated the existence of any harmful health effects from wireless phone RF exposures. However, none of the studies can answer questions about long-term exposures, since the average period of phone use in these studies was around three years. 5. What research is needed to decide whether RF exposure from wireless phones poses a health risk? A combination of laboratory studies and epidemiological studies of people actually using wireless phones would provide some of the data that are needed. Lifetime animal exposure studies could be completed in a few years. However, very large numbers of animals would be needed to provide reliable proof of a cancer promoting effect if one exists. Epidemiological studies can provide data that is directly applicable to human populations, but 10 or more years follow-up may be needed to provide answers about some health effects, such as cancer. This is because the interval between the time of exposure to a cancer-causing agent and the time tumors develop – if they do – may be many, many years. The interpretation of epidemiological studies is hampered by difficulties in measuring actual RF exposure during day-to-day use of wireless phones. Many factors affect this measurement, such as the angle at which the phone is held, or which model of phone is used. 6. What is the FDA doing to find out more about the possible health effects of wireless phone RF? The FDA is working with the U. S. National Toxicology Program and with groups of investigators around the world to ensure that high priority animal studies are conducted to address important questions about the effects of exposure to radio frequency energy (RF). Page 121 Safety The FDA has been a leading participant in the World Health Organization International Electromagnetic Fields (EMF) Project since its inception in 1996. An influential result of this work has been the development of a detailed agenda of research needs that has driven the establishment of new research programs around the world. The project has also helpe develop a series of public information documents on EMF issues. The FDA and the Cellular Telecommunications & Internet Association (CTIA) have a formal Cooperative Research and Development Agreement (CRADA) to do research on wireless phone safety. The FDA provides the scientific oversight, obtaining input from experts in government, industry, and academic organizations. CTIA-funded research is conducted through contracts with independent investigators. The initial research will include both laboratory studies and studies of wireless phone users. The CRADA will also include a broad assessment of additional research needs in the context of the latest research developments around the world. 7. How can I find out how much radio frequency energy exposure I can get by using my wireless phone? All phones sold in the United States must comply with Federal Communications Commission (FCC) guidelines that limit radio frequency energy (RF) exposures. The FCC established these guidelines in consultation with the FDA and the other federal health and safety agencies. The FCC limit for RF exposure from wireless telephones is set at a Specific Absorption Rate (SAR) of 1.6 watts per kilogram (1.6 W/kg). The FCC limit is consistent with the safety standards developed by the Institute of Electrical and Electronic Engineering (IEEE) and the National Council on Radiation Protection and Measurement. The exposure limit takes into consideration the body’s ability to remove heat from the tissues that absorb energy from the wireless phone and is set well below levels known to have effects. Manufacturers of wireless phones must report the RF exposure level for each Page 122 model of phone to the FCC. The FCC website (http://www.fcc.gov/oet/rfsafety) gives directions for locating the FCC identification number on your phone so you can find your phone’s RF exposure level in the online listing. 8. What has the FDA done to measure the radio frequency energy coming from wireless phones? The Institute of Electrical and Electronic Engineers (IEEE) is developing a technical standard for measuring the radio frequency energy (RF) exposure from wireless phones and other wireless handsets with the participation and leadership of FDA scientists and engineers. The standard, “Recommended Practice for Determining the Spatial-Peak Specific Absorption Rate (SAR) in the Human Body Due to Wireless Communications Devices: Experimental Techniques,” sets forth the first consistent test methodology for measuring the rate at which RF is deposited in the heads of wireless phone users. The test method uses a tissue-simulating model of the human head. Standardized SAR test methodology is expected to greatly improve the consistency of measurements made at different laboratories on the same phone. SAR is the measurement of the amount of energy absorbed in tissue, either by the whole body or a small part of the body. It is measured in watts/kg (or milliwatts/g) of matter. This measurement is used to determine whether a wireless phone complies with safety guidelines. 9. What steps can I take to reduce my exposure to radio frequency energy from my wireless phone? If there is a risk from these products – and at this point we do not know that there is – it is probably very small. But if you are concerned about avoiding even potential risks, you can take a few simple steps to minimize your exposure to radio frequency energy (RF). Since time is a key factor in how much exposure a person receives, reducing the amount of time spent using a wireless phone will reduce RF exposure. Page 123 Safety If you must conduct extended conversations by wireless phone every day, you could place more distance between your body and the source of the RF, since the exposure level drops off dramatically with distance. For example, you could use a headset and carry the wireless phone away from your body or use a wireless phone connected to a remote antenna. Again, the scientific data do not demonstrate that wireless phones are harmful. But if you are concerned about the RF exposure from these products, you can use measures like those described above to reduce your RF exposure from wireless phone use. 10. What about children using wireless phones? The scientific evidence does not show a danger to users of wireless phones, including children and teenagers. If you want to take steps to lower exposure to radio frequency energy (RF), the measures described above would apply to children and teenagers using wireless phones. Reducing the time of wireless phone use and increasing the distance between the user and the RF source will reduce RF exposure. Some groups sponsored by other national governments have advised that children be discouraged from using wireless phones at all. For example, the government in the United Kingdom distributed leaflets containing such a recommendation in December 2000. They noted that no evidence exists that using a wireless phone causes brain tumors or other ill effects. Their recommendation to limit wireless phone use by children was strictly precautionary; it was not based on scientific evidence that any health hazard exists. 11. What about wireless phone interference with medical equipment? Radio frequency energy (RF) from wireless phones can interact with some electronic devices. For this reason, the FDA helped develop a detailed test method to measure electromagnetic interference (EMI) of implanted cardiac pacemakers and Page 124 defibrillators from wireless telephones. This test method is now part of a standard sponsored by the Association for the Advancement of Medical instrumentation (AAMI). The final draft, a joint effort by the FDA, medical device manufacturers, and many other groups, was completed in late 2000. This standard will allow manufacturers to ensure that cardiac pacemakers and defibrillators are safe from wireless phone EMI. The FDA has tested hearing aids for interference from handheld wireless phones and helped develop a voluntary standard sponsored by the Institute of Electrical and Electronic Engineers (IEEE). This standard specifies test methods and performance requirements for hearing aids and wireless phones so that no interference occurs when a person uses a “compatible” phone and a “compatible” hearing aid at the same time. This standard was approved by the IEEE in 2000. The FDA continues to monitor the use of wireless phones for possible interactions with other medical devices. Should harmful interference be found to occur, the FDA will conduct testing to assess the interference and work to resolve the problem. 12. Where can I find additional information? For additional information, please refer to the following resources: FDA web page on wireless phones (http://www.fda.gov/cdrh/phones/index.html) Federal Communications Commission (FCC) RF Safety Program (http://www.fcc.gov/oet/rfsafety) International Commission on Non-Ionizing Radiation Protection (http://www.icnirp.de) World Health Organization (WHO) International EMF Project (http://www.who.int/emf) National Radiological Protection Board (UK) (http://www.nrpb.org.uk/) Page 125 Safety Consumer Information on SAR (Specific Absorption Rate) This Model Phone Meets the Government’s Requirements for Exposure to Radio Waves. Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U. S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health. The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR are conducted using standard operating positions specified by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands. Although SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. Because the phone is designed to operate at multiple power levels to use only the power required to reach the network, in general, the closer you are to a wireless base station antenna, the lower the power output. Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model Page 128 phone when tested for use at the ear is 1.17 W/kg and when worn on the body, as described in this user guide, is 0.914 W/kg (body-worn measurements differ among phone models, depending upon available accessories and FCC requirements). While there may be differences between SAR levels of various phones and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF emission guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID BEJVX4500. Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications Industry Association (CTIA) website at http://www.wowcom.com. * In the United States and Canada, the SAR limit for mobile phones used by the public is 1.6 watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements. Page 127 Safety 10 Driver Safety Tips Your wireless phone gives you the powerful ability to communicate by voice almost anywhere, anytime. An important responsibility accompanies the benefits of wireless phones, one that every user must uphold. When operating a car, driving is your first responsibility. When using your wireless phone behind the wheel of a car, practice good common sense and remember the following tips: 1. Get to know your wireless phone and its features such as speed dial and redial. Carefully read your instruction manual and learn to take advantage of valuable features most phones offer, including automatic redial and memory. Also, work to memorize the phone keypad so you can use the speed dial function without taking your attention off the road. 2. When available, use a hands-free device. A number of hands-free wireless phone accessories are readily available today. Whether you choose an installed mounted device for your wireless phone or a speaker phone accessory, take advantage of these devices if available to you. 3. Position your wireless phone within easy reach. Make sure you place your wireless phone within easy reach and where you can reach it without removing your eyes from the road. If you get an incoming call at an inconvenient time, if possible, let your voicemail answer it for you. 4. Suspend conversations during hazardous driving conditions or situations. Let the person you are speaking with know you are driving; if necessary, suspend the call in heavy traffic or hazardous weather conditions. Rain, sleet, snow and ice can be hazardous, but so is heavy traffic. As a driver, your first responsibility is to pay attention to the road. Page 128 5. Do not take notes or look up phone numbers while driving. If you are reading an address book or business card, or writing a “to-do” list while driving a car, you are not watching where you are going. It is common sense. Don’t get caught in a dangerous situation because you are reading or writing and not paying attention to the road or nearby vehicles. 6. Dial sensibly and assess the traffic; if possible, place calls when you are not moving or before pulling into traffic. Try to plan your calls before you begin your trip or attempt to coincide your calls with times you may be stopped at a stop sign, red light or otherwise stationary. But if you need to dial while driving, follow this simple tip — dial only a few numbers, check the road and your mirrors, then continue. 7. Do not engage in stressful or emotional conversations that may be distracting. Stressful or emotional conversations and driving do not mix; they are distracting and even dangerous when you are behind the wheel of a car. Make people you are talking with aware you are driving and if necessary, suspend conversations which have the potential to divert your attention from the road. 8. Use your wireless phone to call for help. Your wireless phone is one of the greatest tools you can own to protect yourself and your family in dangerous situations — with your phone at your side, help is only three numbers away. Dial 911 or other local emergency number in the case of fire, traffic accident, road hazard or medical emergency. Remember, it is a free call on your wireless phonel 9. Use your wireless phone to help others in emergencies. Your wireless phone provides you a perfect opportunity to be a “Good Samaritan” in your community. If you see an auto accident, crime in progress or other serious emergency Page 129 Safety where lives are in danger, call 911 or other local emergency number, as you would want others to do for you. 10. Call roadside assistance or a special wireless nonemergency assistance number when necessary. Certain situations you encounter while driving may require attention, but are not urgent enough to merit a call for emergency services. But you can still use your wireless phone to lend a hand. If you see a broken-down vehicle posing no serious hazard, a broken traffic signal, a minor traffic accident where no one appears injured or a vehicle you know to be stolen, call roadside assistance or other special non-emergency wireless number. For more information, please call to 888-901-SAFE, or visit our website www.wow-com.com Page 130 Accessories There are a variety of accessories available for your mobile phone. Consult your local dealer for availability. Travel Charger The travel charger allows you to charge the battery while away from your home or office. It supports standard U. S. AC120 Volt 60 Hz outlets. It takes 5 hours to charge a completely discharged battery. Battery Two batteries are available. The standard battery, and the extended battery. Desktop Charger The desktop charger allows you to place the phone in a convenient stand for charging. It can charge a completely discharged battery in 3 hours. Cigarette Lighter Charger The cigarette lighter charger allows you to operate the phone and trickle charge the phone’s battery from your vehicle. It takes 5 hours to charge a completely discharged battery. Page 131 Accessories Hands-Free Car Kit (Portable) The hands-free car kit enables you to attach the phone to the power jack in your car, providing you with hands-free operation. It can charge a completely discharged battery in 5 hours. Headset The headset connects to your phone allowing hands-free operation. It includes earpiece, microphone, and integrated call answer/ termination button. NOTE: It operates in vibration/no sound mode on Manner Mode/Silence All Mode even when connected to headset. Holster Page 132 Warranty Information 1. WHAT THIS WARRANTY COVERS: LG offers you a limited warranty that the enclosed subscriber unit and its enclosed accessories will be free from defects in material and workmanship, according to the following terms and conditions: (1) The limited warranty for the unit and enclosed accessories shall be a period of one (1) year from the date of original purchase. The remaining warranty period for the unit being repaired or replaced shall be determined by presentation of the original sales receipt for the purchase of the unit. (2) The limited warranty extends only to the original purchaser of the product and is not assignable or transferable to any subsequent purchaser/ end user. (3) The limited warranty is good only to the original purchaser of the product during the warranty period as long as it is in the U.S., including Alaska, Hawaii, U.S. Territories, and all Canadian Provinces. (4) The external housing and cosmetic parts shall be free of major defects at the time of shipment and, therefore, shall not be covered under these limited warranty terms. (5) Upon request from LG, the consumer must provide information satisfactory to LG to prove the date of purchase or exchange. (6) The customer shall bear the cost of shipping the product to the Customer Service Department of LG. LG shall bear the cost of shipping the product back to the consumer after the completion of service under this limited warranty. 2. WHAT THIS WARRANTY DOES NOT COVER: (1) Defects or damage resulting from use of the product in other than its normal and customary manner. (2) Defect or damage from abnormal use, abnormal conditions, improper storage, exposure to moisture or dampness, unauthorized modifications, unauthorized connections, unauthorized repair, Page 133 Warranty Information misuse, neglect, abuse, accident, alteration, improper installation, or other acts which are not the fault of LG, including damage caused by shipping, blown fuses, or spills of food or liquid. (3) Breakage or damage to antennas unless caused directly by defects in material or workmanship. (4) Alleged defects or malfunctions of the product if the Customer Service Department at LG was not notified by the consumer during the applicable limited warranty period. (5) Products which have had the serial number removed or made illegible. (6) This limited warranty is in lieu of all other warranties, express or implied either in fact or by operations of law, statutory or otherwise, including but not limited to any implied warranty of marketability merchantability or fitness for a particular use. (7) Damage resulting from use of non-LG approved accessories. (8) All plastic surfaces and all other externally exposed parts that are scratched or damaged due to normal customer use. (9) Products operated outside published maximum ratings. (10) Products used or obtained in a rental program. (11) Consumables (such as fuses). 3. STATE LAW RIGHTS: No other express warranty is applicable to this product. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTY OF MARKETABILITY OR MERCHANTABILITY, IS LIMITED TO THE DURATION OF THE EXPRESS WARRANTY HEREIN. LG INFOCOMM U.S.A., NC. SHALL NOT BE LIABLE FOR THE LOSS OF THE USE OF THE PRODUCT, INCONVENIENCE, LOSS OR ANY OTHER DAMAGES, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OF, OR INABILITY TO USE, THIS PRODUCT OR FOR ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTY OF MARKETABILITY OR MERCHANTABILITY APPLICABLE TO THIS PRODUCT. Page 134 Some states do not allow the exclusive of limitation of incidental or consequential damages or limitations on how long an implied warranty lasts; so these limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state. 4. HOW TO GET WARRANTY SERVICE: To obtain warranty service, please call the following telephone number from anywhere in the continental United States: Tel. 1-800-793-8896 or visit www.lgeservice.com. Please call or write for the location of the LGE authorized service center nearest you and the procedures for obtaining warranty claims. Page 135 Index 10 Driver Safety Tips 128 1x Data 106 1x Packet Counter 54 A Accessories 131 Aircraft 113 Alarm Clock 84 Alert Beep 75 Alerts 90 Announce Alerts 82 Answer Call 103 Antenna Care 110 Auto Delete 65 Auto NAM 98 Auto Play 66 Auto Retry 102 Auto Save 65 Auto Volume 105 Auto-Answer 103 B Backlight 92 Banner 91 Battery 16 Battery Information and Care 114 Best Match 82 Blasting Areas 113 C Calculator 87 Call Setup 102 Call Timer 54 Call Waiting 22 Callbacknumber 65 Caller ID 22 Caution 11 Change Code 101 Changing Letter Case 25 Charger and Adapter Safety 114 Check Accessories 7 Clocks 94 Consumer Information on SAR 126 Contacts 47 Contacts Entries 28 Contrast 95 D Data/Fax 106 Default Numbers 36 Deleting 38 Dialed Calls 52 Direct View 65 Display 91 Driving 111 E Editing Contacts Entries 35 Edit Voice Mailboxnumber 65 Electronic Devices 111 Emergency #s 100 Entry Mode 65 Erase All 66 Erase Calls 53 Erase Contacts 101 Ez Tip Calc 87 F FCC RF Exposure Information 10 FDA Consumer Update 118 Page 136 Font Size 66 Fonts 96 G Get Apps 68 Get It Now 67 Get Info 69 Getting Your Phone Started 16 Graphics 76 Groups 49 H Health Care Facilities 112 Hearing Aids 112 Help 83 I Icon Glossary 109 Important Information 7 Inbox 61 K Key Light Timer 93 Key Tone 89 L Language 96 List Contacts 48 Location 108 Lock Mode 21 Lock Phone 99 M Main LCD 92 Making a Call From Your Phone’s Memory 44 Making Calls 19 Manner Mode 20 Menus Overview 14 Menu Style 93 Message Icon Reference 61 Message Objects 77 Messages 55 Missed Call 53 Mobile Web 71 Msg Alerts 65 Msg Settings 64 Music 77 Mute Function 21 My Media 76 My Phone Number 108 My VCard 50 N New E-mail 49 New Message 57 New Number 48 Notepad 86 O One-Touch Dial 104 Other Medical Devices 112 Outbox 63 P Pacemakers 111 Phone Info 108 Phone Numbers With Pauses 40 Phone Operation 111 Phone Overview 12 Port Speed 107 Posted Facilities 113 Power On/Off Tone 91 Page 137 Q Quick-Text 66 R Received Calls 52 Receiving Calls 19 Recent Calls 51 Redialing Calls 19 Reset Default 102 Restrict 100 Ringers 88 S S/W Version 109 Safety 110 Safety Information 115 Saved 63 Searching Your Phone’s Memory 42 Screen Icons 18 Screens 93 Security 99 Select Port 107 Select System 97 Serving System 98 Set NAM 97 Settings 88 Shortcut Help 109 Signal Strength 17 Signature 65 Silence All Mode 20 Soft Keys 73 Sounds 88 Speed Dials 50 Speed Dialing 23 Start Browser 72 System 97 T Text Input 24 Text Input Examples 26 Text Input Modes 25 Theme Colors 94 TIA Safety Information 110 Tips on Efficient Operation 111 Tools 84 TTY Mode 105 V Vehicles 112 Voice 78 Voice Command 23 Voice Commands 81 Voice Mail 57 Voice Memos 80 Voice Privacy 104 Voice Settings 81 Volume 89 Volume Quick Adjustment 21 W Web Messages 75 World Clock 87 P/N: MMBB0091801(1.3) Date: 2004.9.1 Page 138 [END OF MANUAL] ================================================================================ **Disclaimer:** This guide is volunteer-submitted and provided "as is" without warranty. Use caution and verify all information before proceeding. "I Can Work This Thing" assumes no responsibility for accuracy, safety, or any damage/injury resulting from use. For complex or dangerous procedures, consult qualified professionals. Report issues or suggestions to https://icanworkthisthing.com ================================================================================